ML Accessories EMPDL Bedienungsanleitung

INSTALLATION & MAINTENANCE MANUAL

EMPDL

These instructions should be read carefully and retained after installation by the end user for

future reference and maintenance.

These instructions should be used to aid installation of the following product:

EMPDL

GENERAL INSTRUCTIONS

• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations (BS7671)

and current Building Regulations. If in any doubt, consult a qualiﬁed electrician

• Please isolate mains prior to installation or maintenance

• Check the total load on the circuit (including when this luminaire is ﬁtted) does not exceed the rating of the

circuit cable, fuse or circuit breaker

• Please note the IP (Ingress Protection) rating of this product when deciding the location for installation

• Allow 50mm above and around the ﬁtting for air dissipation (do not cover the ﬁtting with insulation)

• This product is for indoor use only

• This product is Class II double insulated

• This product is IP20 rated

SAFETY

INSTALLATION

• Provide power to the required point of installation

• Cut a suitable hole in the mounting surface as per the cut-out details (see Fig. 1) ensuring not to infringe

with any joists, gas / water pipes or electrical cables

INSTALLATION & MAINTENANCE MANUAL

These instructions should be read carefully and retained after installation by the end user for future reference

and maintenance.

These instructions should be used to aid installation of the following product:

EMPDL

SAFETY

•This product must be installed in accordance with the latest edition of the IEE Wiring Regulations

(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician

•Please isolate mains prior to installation or maintenance

•Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of

the circuit cable, fuse or circuit breaker

•Please note the IP (Ingress Protection) rating of this product when deciding the location for installation

•Allow 50mm above and around the fitting for air dissipation (do not cover the fitting with insulation)

•This product is for indoor use only

•This product is Class II double insulated

•This product is IP20 rated

INSTALLATION

•Provide power to the required point of installation

•Cut a suitable hole in the mounting surface as per the cut-out details (see Fig. 1) ensuring not to

infringe with any joists, gas / water pipes or electrical cables

Fig. 1

•This fitting will suit 70mm – 130mm cut-outs when using the adaptor ring (see Fig. 2)

Fig. 2

Fig. 1

• This ﬁtting will suit 70mm – 130mm cut-outs when using the adaptor ring (see Fig. 2)

INSTALLATION & MAINTENANCE MANUAL

These instructions should be read carefully and retained after installation by the end user for future reference

and maintenance.

These instructions should be used to aid installation of the following product:

EMPDL

SAFETY

•This product must be installed in accordance with the latest edition of the IEE Wiring Regulations

(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician

•Please isolate mains prior to installation or maintenance

•Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of

the circuit cable, fuse or circuit breaker

•Please note the IP (Ingress Protection) rating of this product when deciding the location for installation

•Allow 50mm above and around the fitting for air dissipation (do not cover the fitting with insulation)

•This product is for indoor use only

•This product is Class II double insulated

•This product is IP20 rated

INSTALLATION

•Provide power to the required point of installation

•Cut a suitable hole in the mounting surface as per the cut-out details (see Fig. 1) ensuring not to

infringe with any joists, gas / water pipes or electrical cables

Fig. 1

•This fitting will suit 70mm – 130mm cut-outs when using the adaptor ring (see Fig. 2)

Fig. 2

• Connect the luminaire to the mains supply via a suitable junction box (not supplied) ensuring the correct

polarity is observed: L - Live (brown), N - Neutral (blue) (see Fig. 3)

GENERAL

WARNING

This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance

testing. Irreparable damage will occur if this instruction is not followed.

The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole

luminaire should be replaced.

Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the

product.

•Connect the luminaire to the mains supply via a suitable junction box (not supplied) ensuring the

correct polarity is observed: L - Live (brown), N - Neutral (blue) (see Fig. 3)

Fig. 3

•Connect the battery via the plug and socket to the inverter

•Place the battery and inverter into the ceiling void ensuring that there is at least 50mm of clearance

above and around them

•Lift both of the spring clips on the sides of the luminaire and push into the ceiling

•Switch on and check for correct operation, ensuring the green indicator LED is illuminated

•We recommend, on commissioning the installation, a minimum charge period of 24-36 hours before

carrying out an emergency duration test

•If the batteries have been left in a discharged state for an extended period, we recommend that one or

more charge and discharge cycles are completed which should help to restore the battery capacity

WARNING

This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance

testing. Irreparable damage will occur if this instruction is not followed.

GENERAL

The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole

luminaire should be replaced.

Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the

product.

Installing in areas where the temperature consistently drops below 0°C may shorten the battery life.

This product is non-dimmable.

This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities

for where facilities exist.

The batteries in this luminaire are Nickel Cadmium and must be disposed of correctly. Please contact the local

authorities for the disposal of this toxic waste.

WARRANTY

This product has a warranty of 3 years (excluding battery) from date of purchase. Failure to install this product

in accordance with the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the

batch code will invalidate the warranty. If this product should fail within its warranty period, it should be returned

to the place of purchase for a free of charge replacement. ML Accessories does not accept responsibility for

any installation costs associated with the replacement product. Your statutory rights are not affected. ML

Accessories reserve the right to alter product specification without prior notice.

TESTING FOR EMERGENCY LUMINAIRES

Recommended routine test procedure in accordance with BS5266

•Daily check – check LED charge indicator is illuminated

•Monthly functional test - simulate a mains supply failure for approx. 30 seconds by operation of key switch

or switching off circuit breaker. Ensure normal supply is restored after test and ensure charge indicator is

illuminated

•Annual three hour duration test - simulate a mains supply failure for three hour continuous test by operation

of key switch or switching off circuit breaker. Ensure normal supply is restored after test and ensure charge

indicator is illuminated

•If the luminaire fails any of the above tests, please contact a qualified electrician. See below for test record

sheet

Fig. 3

• Connect the battery via the plug and socket to the inverter

• Place the battery and inverter into the ceiling void ensuring that there is at least 50mm of clearance above

and around them

• Lift both of the spring clips on the sides of the luminaire and push into the ceiling

• Switch on and check for correct operation, ensuring the green indicator LED is illuminated

• We recommend, on commissioning the installation, a minimum charge period of 24-36 hours before

carrying out an emergency duration test

• If the batteries have been left in a discharged state for an extended period, we recommend that one or more

charge and discharge cycles are completed which should help to restore the battery capacity

WARRANTY

This product has a warranty of 3 years (excluding battery) from date of purchase. Failure to install this product

in accordance with the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal

of the batch code will invalidate the warranty. If this product should fail within its warranty period, it should

be returned to the place of purchase for a free of charge replacement. ML Accessories does not accept

responsibility for any installation costs associated with the replacement product. Your statutory rights are not

affected. ML Accessories reserve the right to alter product speciﬁcation without prior notice.

Installing in areas where the temperature consistently drops below 0°C may shorten the battery life.

This product is non-dimmable.

This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities

for where facilities exist.

The batteries in this luminaire are Nickel Cadmium and must be disposed of correctly. Please contact the local

authorities for the disposal of this toxic waste.

Recommended routine test procedure in accordance with BS5266

• Daily check – check LED charge indicator is illuminated

• Monthly functional test - simulate a mains supply failure for approx. 30 seconds by operation of key switch

or switching off circuit breaker. Ensure normal supply is restored after test and ensure charge indicator is

illuminated

• Annual three hour duration test - simulate a mains supply failure for three hour continuous test by operation

of key switch or switching off circuit breaker. Ensure normal supply is restored after test and ensure charge

indicator is illuminated

• If the luminaire fails any of the above tests, please contact a qualiﬁed electrician. See below for test record

sheet

TESTING FOR EMERGENCY LUMINAIRES

230V 50Hz, IP20, Class 2, Non-Dim, Non-IC, house, Ta 0~45

DCxxx21_V2

DCSEP21_V2

ML Accessories Limited LU5 4LT

www.mlaccessories.co.uk

INTERNATIONAL

CONTACT DETAILS

INTERNATIONAL

CONTACT DETAILS

INTERNATIONAL

CONTACT DETAILS

45°C

Inhaltsverzeichnis

Andere ML Accessories Beleuchtungsausrüstung Handbücher

ML Accessories

ML Accessories FL8ABK Bedienungsanleitung

ML Accessories

ML Accessories OWALL1 Series Bedienungsanleitung

ML Accessories

ML Accessories TPOV60B Bedienungsanleitung

ML Accessories

ML Accessories AX CCT Bedienungsanleitung

ML Accessories

ML Accessories SPIKEW Bedienungsanleitung

ML Accessories

ML Accessories RW6WW Bedienungsanleitung

ML Accessories

ML Accessories NCLB12 Bedienungsanleitung

ML Accessories

ML Accessories OWALL1 P Series Bedienungsanleitung

ML Accessories

ML Accessories Knightsbridge LEDF24RGB Handbuch

ML Accessories

ML Accessories TRLED14EM Bedienungsanleitung

ML Accessories

ML Accessories WP15CTP Bedienungsanleitung

ML Accessories

ML Accessories NH027 Bedienungsanleitung

ML Accessories

ML Accessories LSPIKEA Bedienungsanleitung

ML Accessories

ML Accessories NH016W Bedienungsanleitung

ML Accessories

ML Accessories WALL1 Bedienungsanleitung

ML Accessories

ML Accessories SUR5LED Bedienungsanleitung

ML Accessories

ML Accessories OSPCKIT Bedienungsanleitung

ML Accessories

ML Accessories BL5BK Bedienungsanleitung

ML Accessories

ML Accessories RD1 Series Bedienungsanleitung

ML Accessories

ML Accessories GUSPBK Bedienungsanleitung

ML Accessories

ML Accessories FLN10 Bedienungsanleitung

ML Accessories

ML Accessories LEDFRA1 Bedienungsanleitung

ML Accessories

ML Accessories MLBA6045 Series Bedienungsanleitung

ML Accessories

ML Accessories T8BLED15EM1 Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung