MobileVision MV2458 Bedienungsanleitung

For Technical Assistance, please call (800) 638-3600,

or visit www.magnadyne.com

User Manual

MV2458 Router

Contents

Pair MV2400 ...................................5

Set SSID

........................................6

Set Login Password .........................7

Restore Factory Settings ...................8

Establish a WiFi Connection...............3

Upgrade Firmware ..........................

Connection History .........................

Reboot ........................................12

Set Date & Time .............................13

Press power button on the MV2458 to

power up the Router and wait until all

lights are blue and flashing

(approximately 2 min).

Step 1

Go to the WiFi setting on your device

(phone, tablet, laptop, etc., make sure

your WiFi is turned on) and click on the

MV2458-2.4G Network. If avaliable, you

can also choose to connect to the

MV2458-5.4G Network.

Step 2

In the Password field type in the

password MV2458WiFi and click the

Join button.

Step 3

The Login screen will open. In the

Password field type in the password

admin and click the Login button.

Step 6

Wait until your device is connected to the

MV2458-2.4G Network.

Step 4

Go to your web browser and in the

address field type in 192.168.10.1 and

click Go or hit Enter.

Step 5

Establish a WiFi Connection

Address: 192.168.10.1

To access the internet using the MV2458 a WiFi connection must be established with the host WiFi.

Password: MV2458WiFi

*Case Sensitive

Password: admin

*Case Sensitive

Wait until the scanning countdown has completed.

The Available WiFi List screen will appear. Click on the

WiFi Network that you would like the Router to connect

to. (If the scroll bar isn’t showing and you are using a

Mac Computer, move the cursor up and down over the

SSID names and the scroll bar should appear.)

If scanning does not happen automatically you may need

to complete the “Reboot” instructions on Page 12.

Step 7

The password pop-up window will appear.

Type in the password for the chosen WiFi

host and click on the Connect button.

Please acquire password from WiFi Host

at your location.

If previously connected, the password will

refresh automatically from your

connection history.

Step 8

Wait until the connecting countdown

has completed.

Step 9

Establish a WiFi Connection

If the password was not typed correctly

a pop-up window will appear stating that

the connection to the Network failed.

Click the OK button. The unit will return

to Step 7 and scan again.

Double check that you are typing the

correct Network password in.

Step 11

The Status Screen will appear showing

the connected Network under the title

MV2400 (Outside) Information.

Congratulations, Setup Complete.

Step 12

The Login screen will open. In the

Password field type in the password admin

and click the Login button. If login is

successful, unit will proceed to Step 12.

Step 10

If the unit will not connect at this

step, it may not have finished it’s 2

minute boot cycle. Start again from

Step 1 and wait 2 minutes for boot

cycle to complete.

Password: admin

*Case Sensitive

Return to Page 3, Step 6 of

“Establish a WiFi Connection”.

Step 6

Select Settings from the drop-down

menu.

Step 1

In Settings select Pair MV2400.

Step 2

In the field Enter Mac Address enter the

MAC address listed in the user’s manual or

the address listed on the device.

The MAC address will have the format of

XX:XX:XX:XX:XX:XX

(Example 40:a5:ef:e1:e2:e9).

It is important to enter this number exactly

as displayed on the device or in the user’s

manual. The MAC address you enter MUST

match the device you are connecting to.

Step 3

Pair MV2400

The MV2458 and MV2400 have been designed to operate cabled by Ethernet or wirelessly. If the WiFi

system is used wirelessly the MV2400 must be paired to the MV2458 for proper operation.

After entering the MAC address click the

Apply button.

Step 4

Wait until the Pair MV2400 countdown

has completed.

Step 5

Select Settings from the drop-down

menu.

Step 1

In Settings select Set SSID.

Step 2

In the field under 5.8G WiFi SSID

replace the default name MV2458-5.8G

with a name of your choice.

Step 3

Set SSID

Personalize your WiFi experience and increase the security of your MV2458 wireless network by

changing the SSID and Password.

If you would like to change the required

password to connect to the 5.8G WiFi

SSID, enter a new password in the field

5.8G WiFi Password to replace the

default MV2458WiFi.

Step 4

Repeat this process for the 2.4G WiFi

SSID and 2.4G WiFi Password to

personalize your connection names and

passwords.

Step 5

Click Apply. Wait until the Set SSID

countdown has completed.

Return to Page 3, Step 2 of

“Establish a WiFi Connection” and use

new SSID & Passwords.

Please note - if you forget your login

password, just use Option 1 of the

“Restore Factory Settings” instructions.

Step 5

Select Settings from the drop-down

menu.

Step 1

In Settings select Set Login Password.

Step 2

In the field Enter Current Password type

in the current password used to login to

the application.

Step 3

In the field Enter New Password type in

the new password to be used to log in

to the application.

Step 4

Click Apply.

Wait until the Set Login Password countdown has

completed.

Return to Page 3, Step 2 of

“Establish a WiFi Connection” and use new password.

Please note - if you forget your login password, just use

Option 1 of the “Restore Factory Settings” instructions.

Step 5

Set Login Password

After initial setup, it’s recommended that the default login password be changed.

admin is the default password.

Make sure the MV2458 is powered on

and wait approximately 2 minutes for it

to completely start up.

Step 1

Using a paper clip, press and hold the

reset button located on the bottom of the

MV2458 for approximately 8 seconds

and then let go.

The WiFi symbol light

will go out and the MV2458 will restore

to factory settings.

Step 2

Wait approximately 2 minutes then

return to Page 3, Step 2 of

“Establish a WiFi Connection”

Step 3

Restore Factory Settings - Option 1

The RV WiFi system can be restored to factory default settings if it is not functioning correctly. Option 1

resets the system by depressing the reset button on the bottom of the MV2458. (This option may be

necessary if you forget your admin password. Default passwords will apply after reset.)

Hold for 8 Sec

When complete, you will be taken to the

Return to Page 3, Step 6 of

“Establish a WiFi Connection” and use

the appropiate password. If the

password has not been changed then

use admin to login.

Step 5

Restore Factory Settings - Option 2

Option 2 uses the in-software restore option. This option can be used to reset both MV2458 (inside unit)

and MV2400 (outside unit) back to factory defaults.

Select Settings from the drop-down

menu.

Step 1

In Settings select Restore Factory

Settings.

Step 2

To clear and restore the MV2458 to

factory settings click the Apply button

below MV2458 Restore.

Wait until the MV2458 Restore status

bar has completed. All settings will be

restored to default.

Return to Page 3, Step 2 of

“Establish a WiFi Connection”.

Step 6

To clear and restore the MV2400 to

factory settings click the Apply button

below MV2400 Restore.

Wait until the MV2400 Restore status

bar has completed.

Step 4

If you want to restore both units to

factory settings, first restore the

MV2400 and then restore the

MV2458.

Step 3

Select Settings from the drop-down

menu.

Step 1

In Settings select Upgrade Firmware.

Step 2

For either the MV2400 or the MV2458

click the Choose File button to select

the firmware update file that you will be

using. This file must be accessible by

the device you are using to perform the

update.

Step 3

After the update is complete, navigate

to the Upgrade Firmware Screen in Step

3and check the file name (located

above the Choose File button) to make

sure the update installed correctly.

Step 6

Once the file is selected the file name

will be displayed in the field next to the

Choose File button.

Step 4

Click the Upload button located below the

file name. The device will begin the update

process. Follow on screen prompts.

Do NOT turn off the power.

Step 5

Upgrade Firmware

As improvements become available, it may be necessary to upgrade the Firmware of the MV2400 and MV2458.

Check for upgrades at www.Magnadyne.com. A PC may be needed to download & perform upgrade.

Andere Handbücher für MV2458

Inhaltsverzeichnis

Andere MobileVision Netzwerk-Router Handbücher

MobileVision

MobileVision MV2458 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise