EN
Quick Install MX-232-IO-Box
www.mobotix.com
Innovations - Made in Germany
The German company MOBOTIX AG is known as the leading pioneer in network camera technology and its
decentralized concept has made high-resolution video systems cost-ecient.
MOBOTIX
AG
•
D-67722
Langmeil
•
Phone:
+49
6302
9816-0
•
Fax:
+49
6302
9816-190
•
[email protected] Security-Vision-Systems
2012 • Declaration of Conformity: www.mobotix.com> Support> Media Library> Certificates
Copyright © MOBOTIX AG 2012 • Made in Germany • Technical information subject to change without notice.
Resetting the MX-232-IO-Box
If the MX-232-IO-Box had been connected to a dierent camera before and not deactivated or reset before
detaching, the left LED (MxBus status) may blink red after establishing the MxBus connection. In this case, you
need to reset the connected and activated MX-232-IO-Box to
factory defaults
:
• Remove the box cover (three screws).
• Bridge the contact surfaces below the Factory Reset label (red circle in figure)
using a screw driver, for example (both LEDs are flashing red/blue with increasing
frequency).
• Only remove the bridge if both LEDs of the MX-232-IO-Box are flashing green
on/o 3 times to indicate that the process has finished successfully.
• Mount the cover back onto the box (torque 0.4Nm).
• Set up the MX-232-IO-Box in the camera (see
«Initializing the MX-232-IO-Box»
).
LED Signaling
Operation I/O Status Connection to Camera
LED USB MxBus
Operation
(left)
Not connected
Regular operation
—Unencrypted
communication
Communication error
I/O Status*
(right)
1x: Input1 closed
2x: Input2 closed
1x: Output1 closed
2x: Output2 closed
1x: RS232 communication
*Displays status of inputs/outputs and RS232 alternately
(pauses, if there is no RS232 communication)
LED o
LED permanently on
LED flashes at regular intervals
Notes
• The MOBOTIX MX-232-IO-Box is to be used only for providing signal inputs/outputs and an RS232 interface
(only when connecting to a camera using USB) for MOBOTIX cameras in IP65 environments.
• For MOBOTIX cameras with MxBus connector and software version MX-V4.1.4.11 or higher.
• Make sure that you adhere to all relevant laws, regulations and that you fulfill all certification requirements
for the intended use.
• Torque for all screws: 0.4Nm.
• Press the white cable plug (eight-wire plug or cable plug 3to 5mm or 5to 7mm) into the casing in such a
way that the rims stick out equally on both sides.
•
The max. baud rate of the RS232 cable depends on the cable length and on the cross-sectional area of the wires.
• The length of the entire MxBus wiring must not exceed 100 m/110yd.
• Cross-sectional area of the MxBus wires: 0.6to 0.8mm (0.8mm recommended to reduce line losses).
• Do not use jumperJ2; it will be used for future extensions of the MX-232-IO-Box.
Initializing the MX-232-IO-Box
1. Open the MOBOTIX camera's user interface in the browser
•
Enter the IP address of the camera that is connected to the MX-232-IO-Box in the browser (admin access rights required):
http://<camera IP address>
2. Make sure that the camera uses PoE class3
• Open the Admin Menu> Ethernet Interface dialog.
• If Power Supply has not been set to Power over Ethernet (Class 3), click on the Change link,
follow the steps of the wizard and activate Power over Ethernet (Class 3).
3. Activate MX-232-IO-Box
• Open the Admin Menu> Manage Hardware Expansions dialog.
•
Option1–
USB: In the line MX-232-IO-Box USB, click on Connect.
•
Option2–
MxBus:
– If the LED icon in the line MxBus Interface is not green, click on Connect.
– In the Admin Menu> Manage MxBus Modules dialog, Devices section, MX-232-IO-Box line, click on
the Activate button.
– If the Update SW button appears in this line, click on it to update the software of the module.
4. Configure events (when using the signal inputs/outputs)
• Open the Setup Menu> Event Overview dialog.
• In the Signal Events section, click on Edit and set the parameters as required (open the help page for this
dialog by clicking on ).
• You can now use the new events in the Setup Menu> Action Group Overview dialog (see the help page
for this dialog by clicking on ).
5. Configure RS232 interface (only when using Option2 – USB)
• Open Admin Menu> Serial Interface> Setup and configure the parameters in the Serial Interface and
Modem as required (see the help page for this dialog by clicking on ).
6. Store the camera configuration
• In the Live screen of the camera, click on Admin Menu> Configuration> Store, permanently store the camera
configuration and reboot the camera.
• Save the camera configuration to the local computer (Admin Menu> Configuration> Save).
Drilling templates for other MOBOTIX wall mounts:
www.mobotix.com> Support> Manuals
Drilling Template for M15/M25 Wall Mount with MX-232-IO-Box
80mm/3.15in
80mm/3.15in
75mm/2.95in
15mm/
0.59in
MX-232-IO-Box
M15/M25 Wall Mount
Installation Instructions
1. Attach the box
Attach the MX-232-IO-Box at the mounting position with the cable ports
pointing downwards (torque 0.4Nm). Next, remove the box cover (three
screws).
2. Establish connection to the camera
You need to follow dierent procedures depending on the connection option:
•
Option1 –
USB
– Remove the slim sealing ring of the straight plug of the USB cable*.
–
Pull the delivered blue sealing ring over the plug, so that the smaller
opening points into the same direction as the plug's contacts.
– Remove blue bayonet catch of the MX-232-IO-Box and pull out
the blue plug.
–
Plug the USB cable with attached sealing ring into the MX-232-IO-Box
and secure the cable using the blue bayonet catch.
– Connect the USB cable to the camera (➔
Camera Manual
).
•
Option2 –
MxBus
–
Before proceeding, make sure there is no voltage on the MxBus
wires!
–
Cut the supplied or existing MxBus wires to size (2-wire, 0.6 to 0.8mm
diameter). When using
wires without jacket
, strip the insulation of
the wires for 5mm and push the wires through the eight-wire plug
(see figure at right).
When using a
cable with jacket
, remove the pre-installed eight-wire
plug and insert the appropriate cable plug (3to 5mm or 5to 7mm).
Press the rubber plug into the casing in such a way that the rims
stick out equally on both sides. Push the cable through the plug,
remove the jacket on a length of 15mm and strip the insulation of
the wires for about 5mm.
– Connect the MxBus wires to the terminals of the MX-232-IO-Box
using the screwdriver. Make sure to maintain the polarity (see sticker
in front of the terminal).
–
Connect the MxBus wires as described in the corresponding manual
to the MOBOTIX camera or to another MxBus module connected to
a camera (e.g. KeypadRFID, DoorMaster). Make sure not to exceed
the overall length of the MxBus wiring of 100 m/110yd.
3. Connect the peripheral devices
Connect the other wires/cables as required and by using the corresponding
cable plugs (inputs, outputs, RS232, MxBus).
4. Lock the cable in place
Insert one or two cable ties depending on the attached cables as shown.
Pull the cable ties tightly around the cables in order to provide strain relief.
5. Mount the cover
Mount the cover back onto the MX-232-IO-Box and ax it using the cover
screws (torque 0.4Nm).
MxBus plug
of MOBOTIX
D15Di
