Monarch 6037 Bedienungsanleitung

MONARCH®PATHFINDER®ULTRA®

GOLD

6037™PRINTER QUICK REFERENCE

Getting Started

1. Charge the main battery. Use either the Monarch® 9462™ or 9464™

battery charger. See the documentation for those chargers.

Important: You must charge the main battery before using it. For optimal

battery life, charge the battery

within three months of receipt

See the

Equipment Manual

for important battery safety

information.

2. Insert the main battery and the backup battery (if needed) in the printer.

A backup battery is already installed in the printer and ready to use.

3. Attach the safety strap found in the documentation package.

4. Load supplies in the printer.

5. Turn on the printer. Your System Administrator must have already

loaded an application in the printer before you can use it.

Attaching the Safety Strap

1. Turn the printer upside down, resting its top on the table.

2. Take the thin end of the safety strap, and push it

through the loop at the bottom of the printer handle

(near the battery compartment).

3. Push the thick end of the safety

strap through the thin end’s

loop.

4. Pull the strap. It may be

necessary to help the thin

end’s loop fit over the

plastic piece in the middle of the strap.

5. Pull the strap tight.

2 Quick Reference

Replacing Batteries

Important: Take the main battery out of the

printer when storing the printer.

1. Turn the printer over and press the button on

the battery compartment door (at the bottom

of the printer’s handle) and slide it open (the

door stays attached).

2. Turn the printer upright, holding your palm

beneath the open battery compartment. Hit

the printer on your hand and catch the

battery as it slides out.

3. Remove the backup battery, if one is already

installed, by turning it slightly

counterclockwise, and pulling it out.

4. At the same angle, place the new battery

(positive side facing away from the main

battery) at the edge of the track under the

spring contact. As you push it in, it will

straighten itself. Make sure the battery lays

flat.

5. Insert a new main battery (non-ribbed end

first).

6. Immediately replace a fully charged main

battery.

7. Slide the compartment door shut. You will have to press the main

battery in slightly so the door fits over it. When the door shuts, you

hear it click into place.

8. Turn on the printer and wait for it to completely initialize.

9. Turn off the printer again.

Important: The last two steps will help avoid reducing the coin cell life.

Main

Battery

Compartment

Door

Button

Backup

Battery

Quick Reference 3

Adjusting the Display Contrast

You can lighten or darken the display using the LCD contrast buttons at the

bottom of the keypad.

♦ Press the (left arrow) to lighten the display.

♦ Press the (right arrow) to darken the display.

Loading Supplies

1. Turn on the printer. The application starts running.

2. Maneuver to the point in the application where you are prompted to load

the supplies.

3. Press the latch buttons and open the

supply cover.

4. Open the spring-loaded supply holder.

5. Place the supply roll in the supply holder

so that the supply feeds from the bottom.

6. Load the supplies for the printing mode

you want: Peel or Non-Peel mode.

Supply

Holder

Latch

Buttons

Supply

Cover

4 Quick Reference

Loading for Non-Peel Mode

A. Feed the supply under the applicator roller

and over the label deflector.

B. Close the supply cover completely.

C. Press ESC to exit.

Loading for Peel Mode

A. Peel and discard the first four inches of labels from the backing paper.

B. Hold the printer upright and gently press

down on the label deflector. (It may be

stiff.)

C. Feed all four inches of the backing paper

over the peel bar and under the

applicator roller and the label deflector.

D. Push the label deflector up until it snaps

into place.

E. Partially close the cover to the first

position.

F. Pull the backing paper over the guide

roller, down to the pinch and feed rollers.

G. Hold the backing paper edge between the

feed and pinch rollers, and press the

trigger.

H. Close the cover and press ESC to exit.

Label

Deflector

Applicator

Roller

Label

Deflector

Peel Bar

Applicator

Roller

Label

Deflector

Feed Roller

(Behind Pinch

Roller

)

Guide Roller

(behind

)

Pinch Roller

Quick Reference 5

Removing Supplies

1. Peel mode only. Tear the backing paper just above the pinch roller.

2. Open the supply cover completely.

3. Spread the supply holder tabs apart and remove the supply roll.

4. Peel mode only. Carefully pull out the supply backing paper still in

place between the pinch and feed rollers.

Cleaning the Printer

Do Not use sharp objects to clean the printer. Use isopropyl alcohol on the

interior areas only (except where specified), never on the exterior.

Cleaning the Printhead

1. Turn off the printer.

2. Open the supply cover and remove the

supplies.

3. Check the supply holder for adhesive

buildup, and clean it, if necessary.

4. Ground yourself by touching metal on

something other than the printer.

Grounding prevents electrostatic

discharge, which may cause damage.

5. Clean the printhead area of all adhesive and label particles using a

Monarch Cleaning Pen (#114226) or a soft cloth moistened with

isopropyl alcohol.

6. Reload the supply and close the cover.

Cleaning the Pinch and Feed Rollers

1. Turn off the printer and open the supply cover.

2. Remove the supplies.

3. Turn the platen roller with your fingers and run a dry, lint-free cloth

across the pinch and feed rollers as they turn. Make sure the rollers are

clean all the way around. If that does not work, use a cloth dampened

slightly with distilled water.

4. Clean any adhesive buildup you see as the rollers turn.

5. Reload the supplies after the printer dries.

Cleaning the Scanner Window

1. Moisten a soft cloth with water.

2. Wipe the window until it is clean.

6 Quick Reference

Cleaning the Black Mark Sensor

1. Turn off the printer and open the supply

cover.

2. Remove the supplies.

3. Clean the black mark sensor with a dry

cotton swab.

4. Reload the supplies and close the supply

cover.

Cleaning the On-Demand Sensor

1. Turn off the printer and open the supply

cover.

2. Remove the supplies.

3. Open the label deflector.

4. Clean the on-demand sensor with a soft

cloth moistened with water.

5. Reload the supplies and close the label

deflector and supply cover.

Clearing Supply Jams

1. Turn off the printer.

2. Open the supply cover completely.

3. Open the label deflector.

4. Remove the supplies.

5. Carefully remove any jammed supply and close the deflector. Do Not

pull the jammed supply out through the front of the label deflector. Do

Not use sharp objects to remove jammed supplies.

6. Remove the extra supply between the pinch and feed rollers.

7. Reload the supplies and close the label deflector.

Cleaning the Platen Roller

Clean the platen roller when you see significant adhesive build-up or a label

is wrapped around the platen roller.

1. Turn off the printer and open the supply cover.

2. Remove the supplies.

3. Hold the printer upright and gently press down on the label deflector. It

may be stiff.

Black Mark

Sensor

On-Demand

Sensor

Quick Reference 7

4. Use a dry, soft-bristle brush, such as a

toothbrush, to clean either the standard

(black) or linerless (red/orange textured)

platen roller.

5. Turn the platen roller with your finger, and

then continue cleaning.

6. Reload the supplies and close the label

deflector and supply cover.

NOTE: DO NOT use alcohol or solvents on linerless (red/orange textured)

platen rollers.

If the brush does not remove all the adhesive:

♦ use isopropyl alcohol ONLY on the standard (black) platen roller.

Moisten a cotton swab with isopropyl alcohol and run the cotton swab

across the platen roller. Turn the platen roller with your finger to make

sure the platen roller is clean all the way around. After cleaning, feed

several inches of supply through without printing to remove any

remaining isopropyl alcohol.

♦ Call Service to clean the linerless (red/orange textured) platen roller.

Scanner Flex Cable

1. Turn off the printer and open the supply

cover.

2. Inspect the scanner flex cable. At any

place that adhesive buildup appears,

clean the cable with 99% isopropyl

alcohol.

3. Close the supply cover.

Troubleshooting

Problem Solution

Printer will not print. Switch to a fully-charged battery.

Load the supply correctly.

Clean the printhead.

Printer will not feed. Switch to a fully-charged battery.

Close the supply cover completely.

Load the supply correctly.

Check the platen roller for jammed labels.

Platen

Roller

Adhesive

Buildup

Scanner

Flex Cable

8 Quick Reference

Problem Solution

Display does not turn on. Switch batteries/Make sure power is on.

CMOS Error Replace the backup battery.

Print has voids or is too

light.

Load the supply correctly / Check for damage.

Close the supply cover completely.

Switch to a fully-charged battery.

Clean the printhead.

Printer partially prints

and fails to respond to

the keypad or trigger.

Re-load the supply or load new supplies.

Clear any supply jams. Clean the printhead.

Switch to a fully-charged battery.

Scanner will not scan a

bar code.

Alter the scan angle and distance. Clean the

scanner window or move to a more dimly lit

area. Scan a bar code you have previously

scanned correctly. Check bar code for voids.

Run a scan test.

Error Codes

Following are some common error codes you may receive. See your System

Administrator if you receive any codes not listed here.

Code(s) Description

004 – 005 Supply size is incorrect. Reload the correct supplies.

267 – 271

410 – 413

Communication error. See your System Administrator.

703 – 704 Load supplies or make sure they are loaded correctly.

750 Printhead is overheated. Turn off the printer to let it cool.

751 – 753 Check the supplies to see if they are loaded correctly.

756 The printer is out of supplies. Load supplies.

757 Load supplies. The calibrated supply length differs by plus

or minus .25 inches from the format.

758 Check supply. Either the supply is not seen, or the on-

demand sensor is broken (purchase optional). Check for a

label jam. Clear the supply path or reload supplies. The

printer does not recalibrate after this error.

762 Low battery. Recharge the battery.

763 Waiting to dispense label. Press Enter.

768 Printhead error. See your System Administrator.

790 – 791 Turn off the printer. Wait two seconds and turn it back on.

904 – 911 System error. See your System Administrator.

SYSTEM

ERROR

VECTOR ##

System error. See your System Administrator.

Note: Information in this document supercedes information in previous versions.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Monarch Drucker Handbücher

Monarch

Monarch Paxar Sierra Sport 3R 9430 Bedienungsanleitung

Monarch

Monarch 9855 Bedienungsanleitung

Monarch

Monarch PATHFINDER Ultra 6030TM Service-Handbuch

Monarch

Monarch 9460 Bedienungs- und Wartungshandbuch

Monarch

Monarch 9855 Bedienungsanleitung

Monarch

Monarch TC9414MQR Bedienungsanleitung

Monarch

Monarch 9400 Series Bedienungsanleitung

Monarch

Monarch 9855 Beilage

Monarch

Monarch Pathfinder Ultra Silver 6032 Bedienungsanleitung

Monarch

Monarch RASCAL 9450 Bedienungsanleitung

Monarch

Monarch 9860 Bedienungsanleitung

Monarch

Monarch 9460 SNP Service-Handbuch

Monarch

Monarch 9430RX Service-Handbuch

Monarch

Monarch 9401 Technisches Dokument

Monarch

Monarch MPCL II Bedienungsanleitung

Monarch

Monarch Pathfinder Ultra Platinum 6039 Bedienungsanleitung

Monarch

Monarch 9445 Technisches Dokument

Monarch

Monarch 9906 Bedienungsanleitung

Monarch

Monarch 9860 Bedienungsanleitung

Monarch

Monarch 6030 Bedienungsanleitung

Monarch

Monarch 9800 Service-Handbuch

Monarch

Monarch 9406 Service-Handbuch

Monarch

Monarch 94 Series Bedienerhandbuch

Monarch

Monarch Paxar 9450 RASCAL Service-Handbuch

Beliebte Drucker Handbücher anderer Marken

Lexmark

Lexmark 1400 Series Handbuch

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Epson

Epson ET-7750 Betriebsanleitung

Canon

Canon CLBR 460ps Bedienungsanleitung

Eltron

Eltron P210 Guide Bedienungsanleitung

Ricoh

Ricoh MD-P1 Bedienungsanleitung

Epson

Epson SC-F7100 series Bedienungsanleitung

Epson

Epson Stylus C40UX Bedienungsanleitung

Canon

Canon imagePASS-A2 Bedienungsanleitung

Canon

Canon S820D Bedienungsanleitung