Monitor Audio STUDIO Bedienungsanleitung

Owners Manual

English 1

Français 8

Italiano 16

Deutsch 24

Español 32

Português 40

Nederlands 48

中文 56

РУССКИЙ 64

日本語 72

80 

Polski 87

Contents

Introduction 2

Featured Technology 2

MPD High Frequency Transducer 2

C-CAM (Ceramic Coated Aluminium/

Magnesium) 2

RDT II (Rigid Diaphragm Technology 2nd

Generation) 2

HiVe II (High Velocity, Low Noise Reﬂex

Port) 3

Single Bolt Though Driver 3

Unpacking 4

2-Channel Positioning 4

Connecting Speaker Cables 5

Bare Wire Connection 5

Banana Plugs 5

Spade Connectors 5

Running-In Your Loudspeakers 5

Upkeep of Cabinets 5

Retention Bolt Adjustment 6

Stands 6

Guarantee 6

Owner Information 6

Speciﬁcations 7

monitoraudio.com 1

ENGLISH

Introduction

Studio is a high-performance loudspeaker system for music enthusiasts looking for absolute performance

in a compact, affordable package. The uncompromising design ethos primarily embraces trickle down

driver technology from the ﬂagship Platinum II series.

Every detail of the signal chain has been considered to achieve neutrality, which required our design team

to think in a very uncompromising fashion. The grille-less design, for example, ensures the speaker always

performs at its optimum level and without concession. Bespoke ﬂoor stands have been created for the

best possible foundation, matching design and performance impeccably.

Featured Technology

MPD High Frequency Transducer

An MPD (Micro Pleated Diaphragm) high frequency transducer has been designed in to provide incredible

articulation due to the low mass diaphragm. The MPD transducer works by rapidly squeezing the pleats

to produce a smooth, wide, naturally fast response way into the ultra-sonic band. As a result, the sound is

more lifelike, releasing the high harmonic spectrum of every note without the distortion that blurs deﬁnition.

C-CAM (Ceramic Coated Aluminium/Magnesium)

C-CAM is an innovative alloy material originally developed by the aerospace industry. It exhibits ideal

qualities for use as loudspeaker cones, being extremely rigid, yet light enough to yield high overall efﬁciency.

C-CAM is formed from an alloy of aluminium and magnesium, which undergoes stress-relieving processes

in manufacturing to avoid surface deformation and molecular weakness. A layer of pure ceramic (alumina)

is deposited onto the surfaces to produce a completely rigid exterior. C-CAM cones are designed to have

high resistance to bending stress. When formed into a cone, C-CAM material provides increased clarity and

reduced distortion compared to conventional cone materials.

RDT II (Rigid Diaphragm Technology 2nd Generation)

RDT II is a composite ‘sandwich’ structure made from ultra-thin low-mass skins, bonded to a honeycomb

NomexR core material. The overall thickness of the RDT II diaphragm is only 2mm, yet it exhibits 150 times

the strength of a conventional loudspeaker cone. RDT II is a unique, innovative development conceived

by Monitor Audio engineers for the new Platinum II series. It uses two skin materials with dissimilar

mechanical properties. C-CAM is used for the front skin, while the rear skin is made from a woven carbon

ﬁbre. This combination is able to reduce distortion by over 8dB above 300Hz, which equates to a 60%

reduction in the energy of harmonic components, making RDT II the lowest distortion cone technology in

Monitor Audio’s history.

The dual 4” RDT II drivers used in Studio are developed from the PL500 II, modiﬁed in this case to produce

bass, as well as mid-range. The DCF ‘Dynamic Coupling Filter’ technology is also incorporated to optimise

and reduce high-frequency cone break-up and increase the critical voice coil circumferential rigidity. As

with Platinum II, Studio drivers are designed to be incredibly low in distortion and use the same magnetic

design principles.

Studio2

HiVe II (High Velocity, Low Noise Reﬂex Port)

Monitor Audio’s port technology uses a straight riﬂed design to accelerate air ﬂow and reduce turbulence.

HiVe II technology has the ability to move air in and out much quicker than a conventional port, the result is

fast powerful bass coupled with superior transient response.

The super slim Studio cabinet is tuned using two rear mounted HiVe II ports mounted at the top and

bottom of the cabinet, this is to ensure the pressure inside the cabinet is balanced symmetrically. The large

port surface area also ensures there is no turbulence and resulting air noise, which can be a problem in

small cabinets.

Single Bolt Though Driver

Studio features our unique single bolt-through driver system, coupled from the rear of the cabinet.

Tightened to a speciﬁc torque setting, it serves to provide the driver with an equal clamping force around

the periphery, whilst ensuring the motor system is braced. Since this is effectively an additional form of

bracing, the cabinet system with drivers installed becomes even more rigid.

monitoraudio.com 3

ENGLISH

Unpacking

Please ensure to allow sufﬁcient clear ﬂoor area, and follow all pictorial guides on the product carton. Cut

the tape sealing the carton, taking care not to cut deeper than the tape, fold back the top folds of the

cardboard to expose the polystyrene and remove any accessories, but leaving the polystyrene in place.

With the carton the right way up and opened, turn it over so the polystyrene end cap is now in contact with

the ﬂoor. Lift carton up to reveal speaker/s, then lift speaker clear of packaging and remove protective bag.

Setting Up

2-Channel Positioning

When arranging a 2-channel system, the listening position and the loudspeakers should form an equilateral

triangle. The speakers should be positioned approximately 6 - 10 feet (1.8 - 3m) apart. The ideal distance

from the rear wall varies depending on tastes and room acoustics, however, the speakers need to be a

minimum of 3 feet (91cm) from the side walls. They should be sited 8 - 18” from the rear wall depending

on how the bass reacts to the room and your personal tastes.

When setting up the speakers, experimentation is strongly advised, as environmental acoustics and

personal preference differ with every installation. If there is insufﬁcient bass present for example, try moving

your speakers closer to a wall. The opposite approach is recommended if there is excessive bass. If

stereo imaging is being lost, try ‘toeing-in’ the speakers slightly. The sound should appear to originate from

the centre point between the speakers, not the speakers themselves.

Studio4

Connecting Speaker Cables

Bare Wire Connection

Unscrew each binding post, and pass the bare wire through the exposed hole, and re-tighten.

Banana Plugs

Remove the red and black plastic plugs from the terminals, using pliers as necessary, and insert the

banana plugs into the standard 4mm holes exposed.

Spade Connectors

Unscrew each binding post, and place the spade connector around the exposed thread, and re-tighten.

Running-In Your Loudspeakers

Run your speakers in by playing normal music or a running-in CD at low-mid listening levels for

approximately 50-70 hours play time. Sound quality may improve further still after 70 hours. This can be

done naturally over time: like a ﬁne wine the performance will improve with age.

Alternatively if you wish to run the speakers continuously on loop you can decrease the audible volume/

presence by placing the speakers face-to-face so that the drivers/tweeters are directly aligned and as

close as possible. Then connect the ampliﬁer to your speakers so that one is as normal (in phase): positive

to positive and negative to negative (red to red and black to black), and the other speaker out of phase:

positive to negative and negative to positive inputs on the speaker.

Upkeep of Cabinets

The ﬁnish of the cabinet can be maintained by regular dusting using a soft micro ﬁbre cloth. The drive units

should only be cleaned with a damp cloth if more than normal dusting is required.

Never use solvents or aggressive cleaning/polishing agents on your Studio Loudspeakers. When in doubt,

test the cleaning product on an inconspicuous area on the cabinet and let it sit for several days before

committing to its use on visible portions of the cabinet.

monitoraudio.com 5

ENGLISH

Studio6

Retention Bolt Adjustment

The Studio loudspeaker has a bolt-through driver ﬁxing to reduce

cabinet colouration. Each bolt acts as a rigid brace, but also removes

the need for conventional driver ﬁxings as well, effectively decoupling

the driver and front bafﬂe to eliminate a further source of resonance.

NOTE: Should this bolt become loose over time, or has

worked loose during transit, then please use the supplied

hex key to tighten the bolt back up. This only needs to be

a quarter turn after the strain has been taken by the bolt.

Stands

New dedicated stands are available, to perfectly compliment both

aesthetically and acoustically with the Studio loudspeakers. They

feature sturdy ‘no ring’ construction to add safe support and isolate the

speakers from resonant frequencies. The new stands’ height has again

been optimised for listening, aligning the speakers tweeters at ideal ear

height within a seated listening position. For more information please

visit our website: www.monitoraudio.com

Guarantee

Both the craftsmanship and the performance of this product is

guaranteed against manufacturing defects for the period of ﬁve years

from the date of purchase (see conditions in the Important Safety

Instructions booklet), provided that the product was supplied by an

authorised Monitor Audio retailer under the consumer sale agreement.

To help us ﬁnd your warranty details within our customer database,

should the need arise, please take a few minutes to register your product(s) online at: monitoraudio.com.

Owner Information

Product Details

Product Serial No:

Date of Purchase:

Dealer Details

Dealer Name:

Address:

Post code:

E-mail address:

monitoraudio.com 7

Speciﬁcations

Studio

System

Configuration 2 Way – 3 driver

Frequency

Response. 48Hz - 60KHz

Sensitivity (1W@1M). 86dB

Nominal Impedance 4 Ohm

(2.9 Ohm Min @ 3.5kHz)

Maximum SPL

(per pair, in room) 110dBA

Power Handling

(RMS) 120W

Recommended

amplifier power into

4 Ohms (RMS)

40-120W

System Alignments Dual slot bass reflex -

HiVe II port system

Mid - H.F Crossover

Frequency 2.7kHz

Drive Unit

Complement

2 x 4” RDT II bass/mid-

range driver

1 x MPD high frequency

transducer

External Dimensions

(Including Terminals)

(H x W x D)

340 x 156.2 x 361mm

13 3/8 x 6 1/8 x 141 3/16 inch

Product Weight 7.58Kg (16lb 9oz)

Finishes Available Satin lacquer finish in black,

white and grey

Monitor Audio reserves the right to alter speciﬁcations without notice.

ENGLISH

Manuel utilisateur

Andere Handbücher für STUDIO

Inhaltsverzeichnis

Sprachen:

Andere Monitor Audio Sprecher Handbücher

Monitor Audio

Monitor Audio Bronze 1 Bedienungsanleitung

Monitor Audio

Monitor Audio AWC265-T2 Bedienungsanleitung

Monitor Audio

Monitor Audio Radius R225 Bedienungsanleitung

Monitor Audio

Monitor Audio CS180 Bedienungsanleitung

Monitor Audio

Monitor Audio Platinum 500 II Handbuch

Monitor Audio

Monitor Audio SB2 Bedienungsanleitung

Monitor Audio

Monitor Audio Creator Series Bedienungsanleitung

Monitor Audio

Monitor Audio Airstream S200 Bedienungsanleitung

Monitor Audio

Monitor Audio CP-CT260 Bedienungsanleitung

Monitor Audio

Monitor Audio ASB-2 Bedienungsanleitung

Monitor Audio

Monitor Audio CSS230 Bedienungsanleitung

Monitor Audio

Monitor Audio CPWT380 Bedienungsanleitung

Monitor Audio

Monitor Audio WT280 Bedienungsanleitung

Monitor Audio

Monitor Audio PLATINUM IN-CEILING II Bedienungsanleitung

Monitor Audio

Monitor Audio CS160 Bedienungsanleitung

Monitor Audio

Monitor Audio IV140 Bedienungsanleitung

Monitor Audio

Monitor Audio Radius R225 Bedienungsanleitung

Monitor Audio

Monitor Audio Loudspeaker Platinum Series Bedienungsanleitung

Monitor Audio

Monitor Audio Airstream s300 Bedienungsanleitung

Monitor Audio

Monitor Audio EN 50020 Bedienungsanleitung

Monitor Audio

Monitor Audio CLIMATE GARDEN Series Bedienungsanleitung

Monitor Audio

Monitor Audio M1 Bedienungsanleitung

Monitor Audio

Monitor Audio GSW12 Bedienungsanleitung

Monitor Audio

Monitor Audio Monitor Reference Series Bedienungsanleitung

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung