Monoprice 21824 Bedienungsanleitung

MONOPRICE

MP Cadet LCD Resin Printer

P/N 21824

User's Manual

3D Printer

Warranty Details

The product is guaranteed to be free from defects in workmanship and motherboard for a

period of 12 months from the date of purchase. The LCD display is a consumable part with an

MTBF of 1200 hours. You may need to purchase and replace it after 1200 hours of operation.

Printing with materials other than resin types recommended on the www.monoprice.com website,

may result in damage to the printer or bad quality prints. Defects that occur within this warranty

period, under normal use and care, will be repaired, replaced,or refunded at our discretion. The

benefits conferred by this warranty are in addition to all rights and remedies in respect of the

product that the consumer has under the law.

Safety Instructions

Before you get started, please read these important safety instructions.

CAUTION: The 3D Printer includes moving parts that can cause injury. Never reach inside of the

3D Printer while it is in operation and allow time for the printer to cool down after operation.

MOVING PARTS

Do not leave the 3D Printer unattended during operation.

Always wear glovesand eye protection whenhandling resin or printing an object.

Always take care when using the scraper. Never direct the scraper towards your fingers.

• The printer must not be exposed to water or rain, or damage will occur.

•The printer is designed to be used with ambient temperature ranging from 15~30°C and

humidity ranging from 20~50%. Operating outside these limits may result in low quality

models.

• In case of emergency, turn off the 3D printer at the power outlet.

• It is recommended that you use eye protection when cleaning/sanding printed models to avoid

small particles contacting your eyes.

MOVING PARTS

Contents

Warranty Details 2

A. Safety Instructions 3

C. Electrical power

D. Useful advice

The box contains

Recommended items

Minimum computer requirements

B. Congratulations

The principle behind your printer

Safety Information

Disposal instructions 6

E. Installation & Assembly Instructions

F. Preparing the Duplicator 7 for Printing

G. Cleaning the Machine and Your Printed Objects

H. Detailed Creation Workshop Software Instructions

System Compatibility

Main Screen

1. Loading a Model

2. Scene View

3. Object Info

4. Move View

5. Mirroring Objects

6. Scaling Objects

7. Rotating Objects

8. View Options

9. Working with Model Support Tools

10. Saving a Scene

11. Slice View

12. Control

13. Congure

13.1 Congure Machine

13.2 Congure Slicing Prole

14. Slicing a Model

15. Connecting Software to Duplicator 7

Repair and Refurbished Goods or Parts Notice

Congratulations

You have just purchased a new type of 3D printer, using Direct UV-light Printing (DUP)

technology. This is a new method of LCD image creation allows controlled UV light to get

through the LCD screen,which hardens liquid to form a model. This revolutionary system is

a new way of printing that uses normal UV light as the energy providing source to initiate

the free radical polymerization necessary to change the liquid resin into your hardened

object.

The principle behind your printer

There are two surprising advantages of this new DUP technology:

i) We can use high-resolution, low-cost LCD screens that are widely available as monitors,

tablets, mobile phones, and televisions,providing phenomenal value for the money.

ii) The energy used by Duplicator 7 printers is again an order of magnitude lower than

used in comparable systems. This is good for your energy bills and the ecology, but there

is a huge performance advantage in that there is no unnecessary energy created. All of the

available photons strike photoinitiators and hand over their energy. In comparable

Digital Light Projector and Laser systems there is a lot of excess energy which can lead to

over-curing.

Safety Information

Read the instructions carefully. Keep this document for future reference. Follow all warnings

and instructions marked on the product.

Observe the following guidelines when connecting and disconnecting power cord to the

printer.

- Insert the power cord into the socket on the back of the printer.

- Turn off the printer before unplugging the power cord.

- The printer cooling fan is supposes to run when you turn on the printer.

- Operate on a table or at, stable surface, ensuring that the machine cannot fall

and is level.

- Do not operate outdoors.

- Do not allow resin or any liquids to get inside the chassis. Wipe up any liquid spills

immediately.

- Store the printer in its original packaging when not in use.

- Unplug the printer when it will not be used for a long period of time.

Electrical Power

This 3D printer uses an AC adapter with an output of 12 VDC, and an input of 110 or

240 VAC, 50/60 Hz. Ensure that your electric outlets provide power in this range.

- Do not allow anything to rest on the power cord. Do not locate this product where

people will walk on the cord.

- If an extension cord is used with this product, ensure that the total ampere rating of the

equipment plugged into the extension cord does not exceed the extension cord's

ampere rating. Also, ensure that the total rating of all products plugged into the wall

outlet does not exceed the fuse rating.

- Do not overload a power outlet, strip, or receptacle by plugging in too many devices.

- Use the product only with the supplied power supply cord set. If you need to replace

the power cord set, make sure that the new power cord meets the following

requirements: detachable type, UL listed/CSA certified, VDE approved or its equivalent,

4.5 meters (15 feet) maximum.

- In case of malfunction, immediately unplug the printer from the power source.

- Do not attempt to fix this product by yourself, as opening or removing covers may

expose you to dangerous voltage points or other risks. For service, contact

Monoprice Technical Support at [email protected]

Unplug this product from the wall outlet and refer servicing to qualied service personnel

when:

- The power cord or plug is damaged, cut, or frayed.

- Liquid was spilled into the product.

- The product was exposed to rain or water.

- The product has been dropped or the case has been damaged.

- The product exhibits a distinct change in performance, indicating a malfunction.

- The product does not operate normally after following the operating instructions.

- Keep the printer out of the reach of small children.

Disposal instructions

To minimize pollution and ensure utmost protection of the global environment, dispose of

this product only in accordance with local, state, or Federal regulations for the disposal of

electronic waste.

Useful Advice

Have supervision when used by a minor.

The resin is an irritant to skin and eyes. Always wear gloves when coming into contact with

the liquid resin.

The printer should be operated on a stable and level surface, preferably away from

direct ambient light.

The box contains

- Duplicator 7 LCD printer with black hood and platform

- Power cord

- VAT with film

- HDMI® cable to connect the 3D printer to the secondary video output of your

computer

- USB cable to connect your computer to the printer

- 1 replacement film for the VAT

- Plastic spatula

- 250ml UV resin

Recommended items

- Gloves

- Paper towels

- Industrial alcohol

- Soft brush or sponge to clean the object

- Plastic container to rinse the resin

Minimum computer requirements

- Dual Core processor or above.

- Windows® or Linux® OS

- Software NOT compatible with Mac® OS X®

- 4 GB RAM memory or above

- Double video output graphics card (one for your monitor, one for the printer HDMI,

with 500MB memory or above. A laptop with dual video output (HDMI) is also

possible.

1.0 Set the printer display:

1.1 Right click the mouse and click the display setting.

1.2 Turn on the printer, connect the HDMI® and USB cables to the computer.

The computer will install the Arduino Mega 2560 driver automatically.

Installation & Assembly

Instructions

1.3 Right click the mouse and click the display setting

1.4 Click the display No.2, then the No.2 display would be highlighted in green color.

1.5 If your display is not horizontal. Change it to horizontal by clicking Direction and

choosing the Horizontal option.

1.6 Apply the change.

2.0 Set the Creation Workshop software:

2.1 Decompress the Creation Workshop zip file. Click the Creation

Workshop logo to run the software.

2.2 Click the Configure button.

2.3 Confi gure the machine:

Click Configure.

Choose the current connection port, which could be Com5, Com6, etc. depending

on your computer.

2.4 Select the screen size 2560x1440, then click + to add the secondary screen.

Apply the change.

Inhaltsverzeichnis

Andere Monoprice 3D-Drucker Handbücher

Monoprice

Monoprice Voxel 33820 Bedienungsanleitung

Monoprice

Monoprice maker architect 13861 Fehlerbehebungshandbuch

Monoprice

Monoprice MP Mini Delta Bedienungsanleitung

Monoprice

Monoprice MP Mini SLA LCD Bedienungsanleitung

Monoprice

Monoprice 15365 Bedienungsanleitung

Monoprice

Monoprice MP CADET Bedienungsanleitung

Monoprice

Monoprice MP Voxel Pro Bedienungsanleitung

Monoprice

Monoprice Delta Pro Bedienungsanleitung

Monoprice

Monoprice MP Voxel Bedienungsanleitung

Monoprice

Monoprice 15710 Bedienungsanleitung

Monoprice

Monoprice MP Delta Pro Bedienungsanleitung

Monoprice

Monoprice Maker Ultimate 2 Bedienungsanleitung

Monoprice

Monoprice Maker Ultimate 2 Bedienungsanleitung

Monoprice

Monoprice MP Voxel Pro Gebrauchsanweisung

Monoprice

Monoprice Maker Select Plus IIIP Bedienungsanleitung

Monoprice

Monoprice Select Mini Pro Bedienungsanleitung

Monoprice

Monoprice 30525 Bedienungsanleitung

Monoprice

Monoprice MP Education Guider II Bedienungsanleitung

Monoprice

Monoprice 43363 Bedienungsanleitung

Monoprice

Monoprice 34438 Bedienungsanleitung

Monoprice

Monoprice maker architect 13861 Bedienungsanleitung

Monoprice

Monoprice MP Maker Pro Mk.1 Bedienungsanleitung

Monoprice

Monoprice 35435 Bedienungsanleitung

Monoprice

Monoprice MP Mibi Delta Bedienungsanleitung

Beliebte 3D-Drucker Handbücher anderer Marken

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

EcubMaker

EcubMaker TOYDIY Bedienungsanleitung

AnyCubic

AnyCubic Kossel Plus Bedienungsanleitung

ReDeTec

ReDeTec ProtoCycler Bedienungsanleitung

Kywoo3D

Kywoo3D Tycoon IDEX Bedienungsanleitung

CraftBot

CraftBot PLUS PRO Bedienungsanleitung

3DGence

3DGence INDUSTRY F340 Bedienungsanleitung

HP Jet Fusion 4200 Betriebsanleitung

Rokit

Rokit AEP Series Bedienungsanleitung

AnkerMake

AnkerMake M5 Bedienungsanleitung

DIYElectronics

DIYElectronics PRUSA I3 Montageanleitung

Ackuretta

Ackuretta FreeShape 120 Bedienungsanleitung

LONGER

LONGER LK5Pro Bedienungsanleitung

Stratasys

Stratasys J850 Bedienungsanleitung

MakerBot

MakerBot Replicator Bedienungsanleitung

Stratasys

Stratasys FDM Vantage Series Bedienungsanleitung

ZYYX

ZYYX Pro II Bedienungsanleitung

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Benutzerhandbuch