Monoprice Maker architect 13861 Bedienungsanleitung

CONTENTS

SAFETY WARNINGS AND GUIDELINES.......................................................................................................................................3

INTRODUCTION................................................................................................................................................................................................4

FEATURES..............................................................................................................................................................................................................4

CUSTOMER SERVICE....................................................................................................................................................................................4

PACKAGE CONTENTS.................................................................................................................................................................................5

NAVIGATING THE MENU SYSTEM...................................................................................................................................................5

UNPACKING AND SETUP.........................................................................................................................................................................6

FINE TUNING PLATFORM HEIGHT..................................................................................................................................................15

SOFTWARE INSTALLATION AND SETUP.................................................................................................................................. 17

TECHNICAL SUPPORT..............................................................................................................................................................................30

REGULATORY COMPLIANCE.............................................................................................................................................................30

Notice for FCC .........................................................................................................................................................................................30

Notice for Industry Canada...........................................................................................................................................................31

SAFETY WARNINGS AND GUIDELINES

The printer is very sensitive to static electricity. Always contact a grounded object

before working with this device. It is recommended to wear an anti-static wrist

strap when working with this device.

Power off and unplug the printer from the power source prior to making repairs or

alterations.

The printer operates at high temperatures. Always allow the nozzle, the extruded

material, and build plate to cool before touching.

Some types of filament can emit a strong odor when heated. Always use this printer

in well-ventilated area.

Do not leave the printer unattended when in operation.

Do not expose this printer to excessive vibration.

Do not expose this printer to water or moisture of any kind. Do not place drinks or

other containers with moisture on or near the printer. If moisture does get in or on

the printer, immediately unplug it from the power outlet and allow it to fully dry

before reapplying power.

Do not place the printer near a heat source, such as a fireplace, heating vent,

radiator, etc.

The power supply for this monitor uses a NEMA 5-15 three prong, grounded plug. Do

not use a "cheater" plug or otherwise bypass the grounding pin.

Do not allow the power cord to be crimped, pinched, stepped on, etc. Ensure that

the power cord does not present a tripping hazard.

Never unplug the unit by pulling on the power cord. Always grasp the connector

head.

This device should only be operated by qualified adults.

In the event of serious operating problem, stop using the unit immediately.

INTRODUCTION

Thank you for purchasing this 3D printer from Monoprice!

This printer features a single extruder and unheated glass build platform. Because the

platform is unheated, it is particularly suited for printing using PLA filament, though it can

print other materials, as well. You can print from a Windows® or Mac® PC using a USB

connection or can print from 3D model files stored on an SD card, without the need for a

PC connection of any kind. This printer is easy to setup and easy to use following the

instructions in this manual and on the menu screen.

FEATURES

Single extrusion print head

Can be upgraded with addition of dual extrusion print head

Unheated glass built platform won't warp

Well suited for printing with PLA filament

Wooden frame for reduced weight

Includes PLA filament for printing right out of the box

Includes 4GB SD card with preinstalled sample 3D models

CUSTOMER SERVICE

The Monoprice Customer Service department is dedicated to ensuring that your ordering,

purchasing, and delivery experience is second to none. If you have any problem with your

order, please give us an opportunity to make it right. You can contact a Monoprice

Customer Service representative through the Live Chat link on our website

www.monoprice.com during normal business hours (Mon-Fri: 5am-7pm PT, Sat-Sun: 9am-

6pm PT) or via email at [email protected]

PACKAGE CONTENTS

Please take an inventory of the package contents to ensure you have all the items listed

below. If anything is missing or damaged, please contact Monoprice Customer Service for a

replacement.

1x 3D Printer 1x Bolt & Hex Wrench Kit

1x Single Extruder 1x Power Supply Cable

1x Spool Holder 1x USB Cable

1x Filament Guide Tube 1x 4GB SD Card

1x Spool White PLA Filament (1 kg) 1x Quick Installation Guide

NAVIGATING THE MENU SYSTEM

The printer has five buttons on the front panel, which are used to navigate and modify

entries in the menu system. As can be seen in the image, the buttons consist of four

"arrow" buttons and a middle button, sometimes referred to as the "M" button.

Use the Up and Down arrow buttons to move the highlight in

the menus.

Use the Middle (M) button to select the currently highlighted

menu entry.

Use the Left arrow button to back out to the previous menu.

Throughout this manual you will be asked to navigate the menu system and select specific

menu entries. For example, you may be told to select:

Utilities > Level Build Plate

To do this, use the Up and Down arrow buttons to move the highlight to the Utilities entry,

then press the Middle (M) button to open the Utilities menu. Next move the highlight to

the Level Build Plate entry, then press the Middle button to activate it.

UNPACKING AND SETUP

Carefully read and perform the following instructions for unpacking the printer and

performing the initial setup. Failure to follow these unpacking instructions could result in

damage to your new printer.

1. Place the box on the floor in the middle of a clean, flat area. Carefully open the top

and remove the accessories box and set it aside.

2. Slide your hands down the sides of the printer to grab the edge of the frame. Lift it

out of the box and place it on your work area.

3. Carefully remove the bubble wrap from the printer.

4. Remove the foam packing from inside the top of the printer, then open the top of

the exposed box and carefully remove the print head/extruder and set it on your

work area next to the printer.

5. Remove the box from inside the printer and set it aside.

6. The build platform is now visible. Grip each side of the platform at the back, next to

the vertical guides and gently pull the platform up to give access to the boxes

under the platform.

7. Remove the boxes from beneath the build platform and set them aside.

8. Carefully remove the bubble wrap from around the print head/extruder. Open the

parts bag and remove two (2) 3/8" long hex screws and the hex wrench.

9. Place the extruder on the extruder seat with the fan facing forward. Secure it to the

seat using two 3/8" long hex screws.

10. Secure the filament guide tube to the back of the printer with the two clips. Ensure

that the guide tube can reach the extruder, but do not connect it to the extruder

yet.

11. Remove the outer plastic nut from the filament support bracket, then insert the

threaded end through the hole in the back of the printer.

Andere Handbücher für maker architect 13861

Inhaltsverzeichnis

Andere Monoprice 3D-Drucker Handbücher

Monoprice

Monoprice 43363 Bedienungsanleitung

Monoprice

Monoprice MP Delta Pro Bedienungsanleitung

Monoprice

Monoprice MP Education Guider II Bedienungsanleitung

Monoprice

Monoprice MP Mini Delta V2 Bedienungsanleitung

Monoprice

Monoprice MP Mini Delta V2 Bedienungsanleitung

Monoprice

Monoprice 30994 Bedienungsanleitung

Monoprice

Monoprice Voxel 33820 Bedienungsanleitung

Monoprice

Monoprice cadet Bedienungsanleitung

Monoprice

Monoprice 33820 Bedienungsanleitung

Monoprice

Monoprice MP Mini Delta Bedienungsanleitung

Monoprice

Monoprice Maker Ultimate 2 Bedienungsanleitung

Monoprice

Monoprice MP CADET Bedienungsanleitung

Monoprice

Monoprice 15365 Bedienungsanleitung

Monoprice

Monoprice MP Mibi Delta Bedienungsanleitung

Monoprice

Monoprice 34438 Bedienungsanleitung

Monoprice

Monoprice MP Mini SLA LCD Bedienungsanleitung

Monoprice

Monoprice 21711 Bedienungsanleitung

Monoprice

Monoprice 30526 Bedienungsanleitung

Monoprice

Monoprice Select Mini 3D Printer V2 Bedienungsanleitung

Monoprice

Monoprice MP Voxel Pro Bedienungsanleitung

Monoprice

Monoprice MP10 Bedienungsanleitung

Monoprice

Monoprice MP Voxel Bedienungsanleitung

Monoprice

Monoprice maker architect 13861 Fehlerbehebungshandbuch

Monoprice

Monoprice Maker Ultimate 2 Bedienungsanleitung

Beliebte 3D-Drucker Handbücher anderer Marken

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

EcubMaker

EcubMaker TOYDIY Bedienungsanleitung

AnyCubic

AnyCubic Kossel Plus Bedienungsanleitung

ReDeTec

ReDeTec ProtoCycler Bedienungsanleitung

Kywoo3D

Kywoo3D Tycoon IDEX Bedienungsanleitung

CraftBot

CraftBot PLUS PRO Bedienungsanleitung

3DGence

3DGence INDUSTRY F340 Bedienungsanleitung

HP Jet Fusion 4200 Betriebsanleitung

Rokit

Rokit AEP Series Bedienungsanleitung

AnkerMake

AnkerMake M5 Bedienungsanleitung

DIYElectronics

DIYElectronics PRUSA I3 Montageanleitung

Ackuretta

Ackuretta FreeShape 120 Bedienungsanleitung

LONGER

LONGER LK5Pro Bedienungsanleitung

Stratasys

Stratasys J850 Bedienungsanleitung

MakerBot

MakerBot Replicator Bedienungsanleitung

Stratasys

Stratasys FDM Vantage Series Bedienungsanleitung

ZYYX

ZYYX Pro II Bedienungsanleitung

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Benutzerhandbuch

Monoprice maker architect 13861 Bedienungsanleitung

Beliebte 3D-Drucker Handbücher anderer Marken