Monoprice 43363 Bedienungsanleitung

Joule 3D Printer DIY Assembly Kit

P/N 43363

User's Manual

SAFETY WARNINGS AND GUIDELINES

Please read this entire manual before using this device, paying extra attention to these safety warnings and guidelines. Please keep this

manual in a safe place for future reference.

•This device is intended for indoor use only.

•Do not expose this device to water or moisture of any kind. Do not place drinks or other containers with moisture on or near the

device. If moisture does get in or on the device, immediately remove it from its power source and allow it to fully dry before

reapplying power.

•Do not touch the device, the power cord, or any other connected cables with wet hands.

•Do not install this device on an unstable surface where it could fall and cause either personal injury or damage to the device

and/or other equipment.

•Do not expose this device to excessive vibration, extreme force, shock, or fluctuations in temperature or humidity.

•Do not expose this device to excessively high temperatures. Do not place it in, on, or near a heat source, such as a fireplace,

stove, radiator, etc. Do not leave it in direct sunlight.

•Do not place or install this device in an area where it can be exposed to excessive amounts of dust, humidity, oil, smoke, or

combustible vapors.

•Use only in a well-ventilated area. Do not use in close, confined spaces.

•Prior to operation, check the unit and power cord for physical damage. Do not use if physical damage has occurred.

•Before plugging the unit into a power outlet, ensure that the outlet provides the same type and level of power required by the

device.

•This device uses a grounded power cord and requires a ground connection for safe operation. Ensure that the power source has

a proper ground connection. Do not modify the plug or use a "cheater" plug to bypass the ground connection.

•Unplug this device from the power source when not in use.

•Take care to prevent damage to the power cord. Do not allow it to become crimped, pinched, walked on, or become tangled

with other cords. Ensure that the power cord does not present a tripping hazard.

•Never unplug the unit by pulling on the power cord. Always grasp the connector head or adapter body.

•Clean using a soft, dry cloth only. Do not use chemical cleaners, solvents, or detergents. For stubborn deposits, moisten the cloth

with warm water.

•This device has no user serviceable parts. Do not attempt to open, service, or modify this device.

•Take care to avoid touching hot parts, including heat blocks, extruder nozzle, extruded filament, and the heated build plate.

•Do not wear gloves when operating or repairing to avoid entanglement.

•Keep the printer and all accessories out of reach of children.

•Do not reach inside the printer during operation.

•Always allow the printer and extruded filament to cool before reaching inside.

•Ensure that the printer is turned off and unplugged from its power source before making repairs or performing service.

CUSTOMER SERVICE

The Monoprice Customer Service department is dedicated to ensuring that your ordering, purchasing, and delivery experience is second

to none. If you have any problem with your order, please give us an opportunity to make it right. You can contact a Monoprice

Customer Service representative through the Live Chat link on our website www.monoprice.com or via email at

support@monoprice.com. Check the website for support times and links.

PACKAGE CONTENTS

Please take an inventory of the package contents to ensure you have all the items listed below. If anything is missing or damaged,

please contact Monoprice Customer Service for a replacement.

1x Printer Base

1x Screen Kit

1x Extruder Kit

1x Z-axis Passive Block

1x X-axis Tensioner

1x Z-axis Motor Kit

1x X-axis Limit Switch Kit

1x XE-axis Kit

1x Z-axis Profile (left)

1x Z-axis Profile (right)

1x Gantry Profile

1x X-axis Profile

1x T-shaped Screw Rod

1x Filament Rack

1x Spool Holder and Nut

2x Gantry Cover

1x Synchronous Belt

1x Scraper

1x Cable Tie

1x Needle

1x microSD™ Card

and Card Reader

2x M6 Pneumatic Joint

1x AC Power Cord

1x Toolkit

(1x Screwdriver, 1x Open-End

Wrench, 2x Allen Wrenches)

1x Nozzle

1x Screen Bracket

2x M4x20 Hexagon Socket

Countersunk Head Screw

2x M4x6 Hexagon Socket Flat

Round Head Screw

6x M5x14 Hexagon Socket Flat

Round Head Screw

2x M4x8 Hexagon Socket Head

Spring Washer Combination

Screw

5x M5x45 Hexagon Socket

Head Spring Washer

Combination Screw

5x M5x25 Hexagon Socket

Head Spring Washer

Combination Screw

6x M4 T-Nuts

4x M4x12 Hexagon Socket Head

Spring Washer Combination

Screw

1x Roll PLA Filament

PRODUCT OVERVIEW

1. XE-axis Kit

2. X-axis Limit Switch

3. Build Plate

4. Y-axis Tensioner

5. Extruder Kit

6. Filament Rack and Spool Holder

7. Z-axis Passive Block

8. X-axis Tensioner

9. Screen

10. Control Knob

11. Printer Base

12. Power Supply

13. Voltage Switch

14. Y-axis Limit Switch

15. Y-axis Motor

16. E-axis Motor

17. X-axis Motor

18. Coupling

19. Z-axis Limit Switch

20. Z-axis Motor

21. Power Switch and Socket

Inhaltsverzeichnis

Andere Monoprice 3D-Drucker Handbücher

Monoprice

Monoprice MP Education Guider II Bedienungsanleitung

Monoprice

Monoprice MP10 Bedienungsanleitung

Monoprice

Monoprice MP Voxel Pro Bedienungsanleitung

Monoprice

Monoprice 30526 Bedienungsanleitung

Monoprice

Monoprice extrusion i3 13860 Bedienungsanleitung

Monoprice

Monoprice 30525 Bedienungsanleitung

Monoprice

Monoprice Maker Select Plus IIIP Bedienungsanleitung

Monoprice

Monoprice Select Mini Pro Bedienungsanleitung

Monoprice

Monoprice maker architect 13861 Fehlerbehebungshandbuch

Monoprice

Monoprice MP Voxel Bedienungsanleitung

Monoprice

Monoprice MP Maker Pro Mk.1 Bedienungsanleitung

Monoprice

Monoprice Delta Pro Bedienungsanleitung

Monoprice

Monoprice MP Maker Pro Mk.1 Bedienungsanleitung

Monoprice

Monoprice MP Mini SLA LCD Bedienungsanleitung

Monoprice

Monoprice 15365 Bedienungsanleitung

Monoprice

Monoprice 21711 Bedienungsanleitung

Monoprice

Monoprice 21824 Bedienungsanleitung

Monoprice

Monoprice MP Mini Delta Bedienungsanleitung

Monoprice

Monoprice 30994 Bedienungsanleitung

Monoprice

Monoprice MP Mini Delta V2 Bedienungsanleitung

Monoprice

Monoprice MP CADET Bedienungsanleitung

Monoprice

Monoprice 13860 Bedienungsanleitung

Monoprice

Monoprice MP Delta Pro Bedienungsanleitung

Monoprice

Monoprice cadet Bedienungsanleitung

Beliebte 3D-Drucker Handbücher anderer Marken

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

EcubMaker

EcubMaker TOYDIY Bedienungsanleitung

AnyCubic

AnyCubic Kossel Plus Bedienungsanleitung

ReDeTec

ReDeTec ProtoCycler Bedienungsanleitung

Kywoo3D

Kywoo3D Tycoon IDEX Bedienungsanleitung

CraftBot

CraftBot PLUS PRO Bedienungsanleitung

3DGence

3DGence INDUSTRY F340 Bedienungsanleitung

HP Jet Fusion 4200 Betriebsanleitung

Rokit

Rokit AEP Series Bedienungsanleitung

AnkerMake

AnkerMake M5 Bedienungsanleitung

DIYElectronics

DIYElectronics PRUSA I3 Montageanleitung

Ackuretta

Ackuretta FreeShape 120 Bedienungsanleitung

LONGER

LONGER LK5Pro Bedienungsanleitung

Stratasys

Stratasys J850 Bedienungsanleitung

MakerBot

MakerBot Replicator Bedienungsanleitung

Stratasys

Stratasys FDM Vantage Series Bedienungsanleitung

ZYYX

ZYYX Pro II Bedienungsanleitung

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Benutzerhandbuch