Monoprice PID 11498 Bedienungsanleitung

SAFETY WARNINGS AND GUIDELINES

For best results, please thoroughly read this manual prior to use, paying particular

attention to the warnings in this Safety section:

•Do not expose this device to water or moisture of any kind. Do not place objects

containing liquid on or near this device.

•Do not expose this device to fire or other heat sources. Do not install it on or near

heat sources, such as ventilators, radiators, or near a fireplace. Do not place

objects with open flame, such as lit candles, on or near this device.

•This device contains no user-serviceable parts. Do not open or attempt to modify

this device.

•Use only the included AC power adapter or an exact replacement (24 VDC,

1.5A).

•Take care to ensure that the power cord does not get crimped, kinked, pinched,

stepped on, or otherwise damaged. Take care that the cord cannot be a trip/fall

hazard.

•When unplugging connections, always grasp the connector head. Never pull on

the cord or wires.

•Never connect speakers rated for less than 4-ohms to the amplifier in stereo

mode. Never connect a speaker rated for less than 8-ohms to the amplifier in

bridged mono mode.

OVERVIEW

This compact and powerful amplifier is packed with advanced features, yet is rugged

enough for commercial environments where a 100% duty cycle is required.

It uses an efficient Class D amplifier design, occupies little space, and requires no

ventilation. It provides either 20-watts (RMS) of power into two channels or 40-watts

(RMS) in bridged mono mode. It accepts two line level inputs and features an internal

Bluetooth receiver as a third input. A switchable limiter provides protection against

distortion and clipping when used near full output, while the switchable contoured

loudness circuit boosts low- and high-frequency signals at lower volume levels. A 9-pin

RS-232 serial interface allows the amplifier to be controlled using a PC.

For best results, please thoroughly read this manual prior to use. Keep this manual in a

safe place for future reference.

FEATURES

•Bluetooth receiver for wireless audio from portable devices

•Bluetooth connectivity with a built-in microphone for hands free communication

with portable phone

•3.5mm stereo line level input

•RCA stereo line level input

•Signal limiter prevents distortion and clipping

•Contoured loudness circuit boosts low- and high-frequency signals at lower

volume levels

•Electronic control of BASS, TREBLE, VOLUME, and BALANCE

•Selectable stereo or bridged mono operation

•12 button IR remote control

•Easy push speaker grip terminals

•Removable Bluetooth antenna with RP-SMA connector

SPECIFICATIONS

Power Output: 20 watts (RMS) per channel into 4 ohm loads

Frequency Response: 20Hz to 20kHz (-3dB)

Signal to Noise Ratio: -95dB @ 1kHz (4 ohms)

Input Sensitivity: 330mV (17W 4-ohms)

Input Impedance: 10 kilohms

Power Requirement:24VDC, 1.5A (AC Adapter included)

Dimensions (HxWxD): 1-7/8" x 5-5/8" x 4-3/4", including knobs and connectors

PACKAGE CONTENTS

After receiving the product, please inventory the contents to ensure you have all the

proper parts, as listed below. If anything is missing or damaged, please contact

Monoprice Customer Service for a replacement.

1x 20-watt per channel amplifier

1x IR remote control

1x AC power adapter

IR REMOTE CONTROL

The included IR remote control provides convenient access to most functions found on

the front panel of the amplifier.

Source Selection: LINE1, LINE2, Bluetooth

Mute: ON/OFF

Power: ON/OFF

Treble: UP/DOWN

Bass: UP/DOWN

Balance: LEFT/RIGHT

CONTROLS AND CONNECTIONS

Front Panel

Stereo/Bridge: Selects stereo or mono bridged operation. In bridged mode, the

amplifier provides one 40W RMS output channel, capable of driving an 8-ohm

load.

Source: Pressing this button toggles between LINE1, LINE2, and BLUETOOTH

sources, as indicated by the LED indicators directly above the button.

Select: Press this knob to select VOLUME, BASS, TREBLE, or BALANCE. The LEDs

above the knob indicate the current selection. Turn the knob to adjust the level of

the selected function.

Bluetooth: Press this button to perform Bluetooth functions. See the Bluetooth section

below for details.

Power: Pressing this button toggles the unit ON and OFF.

Rear Panel

RS-232: For connection of an external serial control device, such as a PC

Antenna: For connection of the included Bluetooth antenna. NOTE: Use extreme care

in handling this delicate antenna.

DIP Switches:

Loudness: Boosts high and low frequency signals at low volume levels. The

effect of this diminished as the volume setting is increased. Once the

volume reaches 70% of maximum, this control has no effect.

Limiter: Automatically reduces input sensitivity as the amplifier approaches its

maximum output level. This prevents distortion and clipping when the amp

is used near full output. Because this does tend to reduce the overall

dynamic range, it is recommended that this not be used in high fidelity

applications.

Note: After changing the DIP switches, the amp must be temporarily unplugged

from its power source for the changes to take effect.

Line 1: Stereo 3.5mm TRS jack for connecting the headphone output of mobile devices.

Line 2: Left and right RCA jacks for connecting consumer audio devices, such as CD or

tape players, tuners, and other devices with RCA line level outputs.

Speaker Output: Easy push speaker grip terminals for connecting speakers. Normally

you would connect a single pair of 4- or 8-ohm speakers. However, because this

amp can drive 4-ohm loads, you can connect two 8-ohm speakers in parallel to

each output channel. To do this, simply insert two wires into each spring terminal.

BRIDGED MODE

This amplifier normally delivers a 20 watt output to each of two channels. However, it is

possible to "bridge" these two channels, thereby creating a single channel with 40 watts

output. This is useful in environments where maximum output power is desired and

stereo separation is unnecessary (such as in public address situations). Note that in

bridged mode, the amplifier can only drive an 8-ohm or larger load. Do not connect a

speaker rated for less than 8 ohms. With the amplifier powered OFF, slide the front

panel switch to the BRIDGE position. On the rear, connect the wire from a single

speaker to the RIGHT channel's negative (-) terminal and the LEFT channel (+)

terminal. The remaining two speaker output terminals will not be used.

BLUETOOTH CONNECTION

To connect your Bluetooth equipped mobile device to the amplifier, perform the

following steps:

1. With the amplifier powered ON, press the SOURCE button repeatedly until the BT

indicator lights.

2. When BT is selected, you will notice the red indicator above the BLUETOOTH

button blinking. The amplifier is ready to pair with your device.

3. On your mobile device, ensure that Bluetooth is enabled. Scan for nearby devices

and select the Monoprice AMP entry. On some devices you may be asked for a

passcode. Enter 0000 (four zeroes). On some devices you may need to manually

connect to the amplifier after pairing is complete. In some cases you may need to

press the Bluetooth button on the amplifier to connect.

4. To disconnect the pairing, press and hold the Bluetooth button for about 3

seconds. Once it is unpaired, the amplifier is ready to pair with another device.

PHONE CALLS

This amplifier is equipped with a built-in microphone, allowing you to use it as a hands-

free communications device:

To answer an incoming call, press the Bluetooth button.

To reject an incoming call, press and hold the Bluetooth button for about 3 seconds.

To hang up after completing a call, press the Bluetooth button.

RS-232 INTERFACE

Following are the control commands for the RS-232 interface:

1:9600.n.8.1

<CR>: Enter Key

<Esc>: Escape Key

<Space>: Space Key

2: Host respond prompt: PA>

3: Show All PA Status: Type: Now<CR>

4: Power On/Off control: Type:

Power<Space>On<CR>------Power On

Power<Space>Off<CR>------Power Off

Power<Space>Toggle<CR>------Power toggle control

5: Mute On/Off control: Type:

Mute<Space>On<CR>-------Mute On

Mute<Space>Off<CR>-------Mute Off

Mute<Space>Toggle<CR>-------Mute toggle control

6: Volume control:

Type: Volume<Space>xx<CR>----Volume xx (xx range 0-79)

7: Source control:

Type: Source<Space>x<CR> x=1/2/3

8: Treble control:

Type: Treble<Space>xx<CR>-----xx :Treble control (+7 0 -7)

9: Bass control:

Type: Bass<Space>xx<CR>-------xx :Bass control (+7 0 -7)

10: Balance control:

Type: Balance<Space>xx<CR>----xx :Balance control (L9 0 R9)

11: Save memory now:

Type: Save<CR>----stores all current setting other than power on/off status

Inhaltsverzeichnis

Andere Monoprice Verstärker Handbücher

Monoprice

Monoprice MONOLITH 33306 Bedienungsanleitung

Monoprice

Monoprice Wireless Speaker Transmitter Bedienungsanleitung

Monoprice

Monoprice CasaTunes CT-250A Bedienungsanleitung

Monoprice

Monoprice Monolith 24460 Bedienungsanleitung

Monoprice

Monoprice HS-102 Bedienungsanleitung

Monoprice

Monoprice 16153 Bedienungsanleitung

Monoprice

Monoprice SWA-200 Bedienungsanleitung

Monoprice

Monoprice 36373 Bedienungsanleitung

Monoprice

Monoprice 39261 Bedienungsanleitung

Monoprice

Monoprice INDIO 611710 Gebrauchsanweisung

Monoprice

Monoprice MONOLITH 7 Bedienungsanleitung

Monoprice

Monoprice 16154 Bedienungsanleitung

Monoprice

Monoprice SWA-400 Bedienungsanleitung

Monoprice

Monoprice PID 11497 Bedienungsanleitung

Monoprice

Monoprice 13194 Bedienungsanleitung

Monoprice

Monoprice Cat5 x1 Bedienungsanleitung

Monoprice

Monoprice 18800 Bedienungsanleitung

Monoprice

Monoprice Monolith M5100X Bedienungsanleitung

Monoprice

Monoprice 31027 Bedienungsanleitung

Monoprice

Monoprice Monolith Bedienungsanleitung

Monoprice

Monoprice 11567 Bedienungsanleitung

Monoprice

Monoprice 18802 Bedienungsanleitung

Monoprice

Monoprice 13194 Bedienungsanleitung

Monoprice

Monoprice WolfPack HDTVNOM18800 Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung