Monoprice 21792 Bedienungsanleitung

MONOPRICE

Blackbird™4K HDBaseT™Extender Kit

P/N 21792

User's Manual

SAFETY WARNINGS AND GUIDELINES

Please read this entire manual before using this device, paying extra attention to these

safety warnings and guidelines. Please keep this manual in a safe place for future reference.

This device is intended for indoor use only.

Do not expose this device to water or moisture of any kind. Do not place drinks or

other containers with moisture on or near the device. If moisture does get in or on

the device, immediately unplug it from the power outlet and allow it to fully dry

before reapplying power.

Do not touch the device, the power cord, or any other connected cables with wet

hands.

Do not expose this device to excessively high temperatures. Do not place it in, on,

or near heat sources, such as a fireplace, stove, radiator, etc. Do not leave it in direct

sunlight.

Prior to operation, check the unit and power cord for physical damage. Do not use if

physical damage has occurred.

Unplug this device from the power source when not in use.

Take care to prevent damage to the power cord. Do not allow it to become

crimped, pinched, walked on, or become tangled with other cords. Ensure that the

power cord does not present a tripping hazard.

Never unplug the unit by pulling on the power cord. Always grasp the connector

head or adapter body.

Ensure that power is turned off and disconnected before making any electrical

connections.

Clean using a soft, dry cloth only. Do not use chemical cleaners, solvents, or

detergents. For stubborn deposits, moisten the cloth with warm water.

This device has no user serviceable parts. Do not attempt to open, service, or

modify this device.

INTRODUCTION

Thank you for purchasing this Blackbird™4K HDBaseT™Extender Kit! This kit consists of a

transmitter and receiver, which allows a 1080p HDMI® signal to be transmitted to distances

up to 328 feet (100 meters) and a 4K signal to be transmitted to distances up to 229 feet

(70 meters) over a single Cat6 Ethernet cable. It supports video resolutions up to 4K@60Hz

4:4:4 and includes the Power over HDBaseT (PoH) feature, which allows the transmitter or

receiver to be powered by the other device over the Ethernet cable. It supports bi-

directional extension of infrared remote control, RS232 computer data, and 10/100Mbps

Ethernet network traffic. It is fully compliant with the HDMI 2.0 and HDCP 2.2 specifications

and provides up to 18Gbps bandwidth.

FEATURES

Supports video resolutions up to 4K@60Hz 4:4:4

Extends 1080p signals to distances up to 328 feet (100 meters) and 4K signals to

distances up to 229 feet (70 meters)

Fully compliant with the HDMI 2.0 and HDCP 2.2 specifications

Supports the Power over HDBaseT feature, which allows the transmitter or receiver

to be powered by the other device over the Ethernet cable

Supports bi-directional IR and RS232 pass-through

Supports HDR

Includes a 4-port 10/100Mbps Ethernet switch

CUSTOMER SERVICE

The Monoprice Customer Service department is dedicated to ensuring that your ordering,

purchasing, and delivery experience is second to none. If you have any problem with your

order, please give us an opportunity to make it right. You can contact a Monoprice

Customer Service representative through the Live Chat link on our website

www.monoprice.com during normal business hours (Mon-Fri: 5am-7pm PT, Sat-Sun: 9am-

6pm PT) or via email at [email protected]

PACKAGE CONTENTS

Please take an inventory of the package contents to ensure you have all the items listed

below. If anything is missing or damaged, please contact Monoprice Customer Service for a

replacement.

1x HDBaseT™transmitter

1x HDBaseT receiver

2x 3-pin to DB9 RS232 cables

4x Mounting brackets

8x Screws

1x IR transmitter

1x IR receiver

8x Plastic cushions

1x User's manual

PRODUCT OVERVIEW

Transmitter

1. RS232 MODE Switch: Selects the RS232 mode. The CTRL position is the normal

operating mode where RS232 data is passed back and forth with the receiver. The

two UPDATE positions are for updating the transmitter's firmware using one of two

methods. See the

FIRMWARE UPDATE

section for details.

2. LINK LED Indicator: The LED illuminates green when there is a valid HDBaseT

connection with the receiver. The LED is off when there is no valid link.

3. HDCP LED Indicator: The LED illuminates green when there is HDMI video traffic

with HDCP. It will blink green when there is HDMI® video traffic without HDCP and

will be off when there is no HDMI video traffic.

4. POWER LED Indicator: The LED illuminates red when power is applied and is off

when no power is present.

5. RS232 Connector: Connector for the included 3-pin to DB9 RS232 cable.

6. IR IN Jack: 3.5mm jack for connecting the IR receiver.

7. IR OUT Jack: 3.5mm jack for connecting the IR transmitter.

8. HDMI IN Port: HDMI® port for connecting the HDMI cable from the video source

device.

9. HDBT OUT Jack: RJ45 jack for connecting the Ethernet cable to the receiver.

10. ETHERNET Jacks: RJ45 jacks for connecting to an existing Ethernet network and/or

devices.

11. DC IN Jack: DC barrel connector for connecting the included AC power adapter.

Receiver

1. RS232 MODE Switch: Selects the RS232 mode. The CTRL position is the normal

operating mode where RS232 data is passed back and forth with the transmitter.

The two UPDATE positions are for updating the receiver's firmware using one of

two methods. See the

FIRMWARE UPDATE

section for details.

2. LINK LED Indicator: The LED illuminates green when there is a valid HDBaseT™

connection with the receiver. The LED is off when there is no valid link.

3. HDCP LED Indicator: The LED illuminates green when there is HDMI® video traffic

with HDCP. It will blink green when there is HDMI video traffic without HDCP. It will

be off when there is no HDMI video traffic.

4. POWER LED Indicator: The LED illuminates red when power is applied and is off

when no power is present.

5. RS232 Connector: Connector for the included 3-pin to DB9 RS232 cable.

6. IR IN Jack: 3.5mm jack for connecting the IR receiver.

7. IR OUT Jack: 3.5mm jack for connecting the IR transmitter.

8. HDMI OUT Port: HDMI port for connecting the HDMI® cable to the video display.

9. HDBT IN Jack: RJ45 jack for connecting the Ethernet cable to the transmitter.

10. ETHERNET Jacks: RJ45 jacks for connecting to an existing Ethernet network and/or

devices.

11. DC IN Jack: DC barrel connector for connecting the included AC power adapter.

SAMPLE CONNECTION DIAGRAM

INSTALLATION

Perform the following steps to install this HDBaseT™ Extender Kit.

1. Ensure that all equipment to be connected is powered off and unplugged from its

power source.

2. Place the transmitter and receiver in their intended locations. Use the included

mounting brackets to secure the units in place, as desired.

3. Using a High Speed HDMI® Cable (not included), plug one end into the HDMI input

on your display, then plug the other end into the HDMI OUT port on the receiver.

4. Using a Cat6 Ethernet cable (not included), plug one end into the HDBT IN jack on

the receiver, then plug the other end into the HDBT OUT jack on the transmitter.

Note that if this cable is to be run in or through wall, it must be rated for in-wall use.

5. Using a High Speed HDMI Cable (not included), plug one end into the HDMI IN port

on the transmitter, then plug the other end into the HDMI output on your video

source device (e.g., Blu-ray Disc™ player, DVD player, game console, etc.).

6. (Optional) Using an Ethernet cable (not included), plug one end into one of the

ETHERNET ports on either the transmitter or receiver, then plug the other end into

an Ethernet port on a network router or switch.

7. (Optional) Using an Ethernet cable (not included), plug one end into an available

ETHERNET port on the transmitter or receiver, then plug the other end into the

Ethernet port on your computer, Ethernet switch, or other network device. Repeat

for up to two additional network connections.

8. (Optional) If you want to control the video source device from the remote location,

plug the included IR receiver into the IR IN jack on the receiver, then position the IR

"eye" where it can receive IR signals from your remote control. Alternatively, if you

want to control the remote display from the source side, plug the included IR

receiver into the IR IN jack on the transmitter, then position the IR "eye" where it can

receiver IR signals from your remote control.

9. (Optional) If you want to control the video source device from the remote location,

plug the included IR transmitter into the IR OUT jack on the transmitter, then

position the IR emitter where it can transmit IR signals to the IR "eye" on the video

source device. Alternatively, if you want to control the remote display from the

source end, plug the include IR transmitter into the IR OUT jack on the receiver, then

position the IR emitter where it can transmit IR signals to the IR "eye" on the display.

10. Plug the DC barrel connector on the included AC power adapter into the DC IN jack

on either the transmitter or the receiver, the plug the adapter into a nearby AC

power outlet. Note that the unit that is not connected to the AC power adapter will

receive its power from the other unit over the Cat6 Ethernet cable.

11. Plug in and power on all connected equipment. Start video playback on your source

device, then verify that you can see the video on the remote display. If you are

using the IR extension feature, verify that you can control the intended device from

the other end. If you connected computers or other network devices to the

ETHERNET ports, verify that you have network access to the connected device.

FIRMWARE UPDATE

Perform the following steps to update the firmware for both the transmitter and receiver.

1. Plug the included 3-pin to DB9 RS232 Cable into the 3-pin RS232 connector on the

receiver or transmitter, then plug the other end into the RS232 serial connector on

your PC.

2. If you will be updating the Valens IC program, slide the RS232 Mode Switch to the

UPDATE A position. If you will be update the Compression IC program, slide the

RS232 Mode Switch to the UPDATE B position instead.

3. Locate the update batch (.bat) file on your computer and double-click it to run it.

TECHNICAL SUPPORT

Monoprice is pleased to provide free, live, online technical support to assist you with any

questions you may have about installation, setup, troubleshooting, or product

recommendations. If you ever need assistance with your new product, please come online

to talk to one of our friendly and knowledgeable Tech Support Associates. Technical

support is available through the online chat button on our website www.monoprice.com

during regular business hours, 7 days a week. You can also get assistance through email by

sending a message to tech@monoprice.com

SPECIFICATIONS

Model

21792

Maximum Transmission Distance

up to 328 feet (100m) for 1080p signals

up to 229 feet (70m) for 4K signals

Maximum Resolution

4K@60Hz 4:4:4

Maximum Bandwidth

18Gbps

HDMI® Standards

HDMI 2.0 and HDCP 2.2

Ethernet Standard

10/100Mbps

Power Source

24 VDC, 1.25A AC adapter or PoH

AC Adapter Input Power

100 ~ 240 VAC, 50/60 Hz

Maximum Power Consumption

20 watts

Operating Temperature

+14 ~ +122°F (-10 ~ +50°C)

Operating Humidity

0 ~ 90% RH, non-condensing

Dimensions (each)

6.0" x 0.6" x 4.1" (152 x 16 x 104 mm)

Weight (each)

8.5 oz. (240g)

Inhaltsverzeichnis

Andere Monoprice Extender Handbücher

Monoprice

Monoprice KVM-LII Bedienungsanleitung

Monoprice

Monoprice BLACKBIRD 44570 Bedienungsanleitung

Monoprice

Monoprice 41097 Bedienungsanleitung

Monoprice

Monoprice Blackbird 24279 Bedienungsanleitung

Monoprice

Monoprice Blackbird 27842 Bedienungsanleitung

Monoprice

Monoprice Blackbird 43959 Betriebsanleitung

Monoprice

Monoprice MIR-500 Bedienungsanleitung

Monoprice

Monoprice 24281 Bedienungsanleitung

Monoprice

Monoprice 18784 Bedienungsanleitung

Monoprice

Monoprice DVI-LH Bedienungsanleitung

Monoprice

Monoprice BitPath AV 16227 Bedienungsanleitung

Monoprice

Monoprice Blackbird 30915 Bedienungsanleitung

Monoprice

Monoprice MIR-300 Bedienungsanleitung

Monoprice

Monoprice SE535LTD Bedienungsanleitung

Monoprice

Monoprice Blackbird Pro WiHD 16049 Bedienungsanleitung

Monoprice

Monoprice 27841 Bedienungsanleitung

Monoprice

Monoprice Blackbird Pro WiHD 39625 Bedienungsanleitung

Monoprice

Monoprice Blackbird 44571 Bedienungsanleitung

Monoprice

Monoprice VGA Bedienungsanleitung

Monoprice

Monoprice 10224 Bedienungsanleitung

Monoprice

Monoprice IR-320 Bedienungsanleitung

Monoprice

Monoprice 34898 Bedienungsanleitung

Monoprice

Monoprice HDMI-LH Bedienungsanleitung

Monoprice

Monoprice Blackbird 4K Pro HDBaseT Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Marmitek

Marmitek MegaView70 Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung