Monoprice Blackbird 30446 Bedienungsanleitung

Blackbird™4K HDBaseT™Extender Kit

P/N 30446

User's Manual

SAFETY WARNINGS AND GUIDELINES

Please read this entire manual before using this device, paying extra attention to these

safety warnings and guidelines. Please keep this manual in a safe place for future reference.

This device is intended for indoor use only.

Do not expose this device to water or moisture of any kind. Do not place drinks or

other containers with moisture on or near the device. If moisture does get in or on

the device, immediately unplug it from the power outlet and allow it to fully dry

before reapplying power.

Do not touch the device, the power cord, or any other connected cables with wet

hands.

Do not expose this device to excessively high temperatures. Do not place it in, on,

or near heat sources, such as a fireplace, stove, radiator, etc. Do not leave it in direct

sunlight.

Prior to operation, check the unit and power cord for physical damage. Do not use if

physical damage has occurred.

Before plugging the unit into a power outlet, ensure that the outlet provides the

same type and level of power required by the device.

Unplug this device from the power source when not in use.

Take care to prevent damage to the power cord. Do not allow it to become

crimped, pinched, walked on, or become tangled with other cords. Ensure that the

power cord does not present a tripping hazard.

Never unplug the unit by pulling on the power cord. Always grasp the connector

head or adapter body.

Ensure that power is turned off and disconnected before making any electrical

connections.

Clean using a soft, dry cloth only. Do not use chemical cleaners, solvents, or

detergents. For stubborn deposits, moisten the cloth with warm water.

This device has no user serviceable parts. Do not attempt to open, service, or

modify this device.

INTRODUCTION

Thank you for purchasing this Blackbird™ 4K HDBaseT™Extender Kit! This kit allows you to

extend 1080p@60Hz HDMI® signals to distances up to 229 feet (70 meters) and 4K@60Hz

signals to distances up to 131 feet (40 meters) over a single Cat6 Ethernet cable. It supports

IR and RS-232 pass-through and employs Visually Lossless Compression (VLC) technology

to ensure flawless UHD video transmission.

FEATURES

Supports video resolutions up to 4K@60Hz 4:4:4

Can extend 1080p@60Hz HDMI® signals to distances up to 229 feet (70 meters) and

4K@60Hz signals to distances up to 131 feet (40 meters) over a single Cat6 Ethernet

cable

Compliant with the HDMI 2.0 and HDCP 2.2 standards

Supports Power over Cable (PoC) in either direction

Supports CEC, IR, and RS-232 pass-through

Supports HDR

CUSTOMER SERVICE

The Monoprice Customer Service department is dedicated to ensuring that your ordering,

purchasing, and delivery experience is second to none. If you have any problem with your

order, please give us an opportunity to make it right. You can contact a Monoprice

Customer Service representative through the Live Chat link on our website

www.monoprice.com during normal business hours (Mon-Fri: 5am-7pm PT, Sat-Sun: 9am-

6pm PT) or via email at [email protected]

PACKAGE CONTENTS

Please take an inventory of the package contents to ensure you have all the items listed

below. If anything is missing or damaged, please contact Monoprice Customer Service for a

replacement.

1x Blackbird™ HDBaseT™

transmitter

1x Blackbird HDBaseT receiver

1x AC power adapter (12 VDC, 2A)

1x RS-232 cable

4x Mounting ears

4x Mounting screws

1x 3-pin Phoenix connector

8x Plastic feet

1x User's manual

PRODUCT OVERVIEW

Transmitter

1. MODE SWITCH: Put the Mode switch in the CTRL position for normal operation and

to allow RS-232 control pass-through. Put the switch in the UPDATE A position to

update the Valens IC program. Finally, put the switch in the UPDATE B position to

update the compression IC program.

2. POWER LED: The LED illuminates red when power is applied.

3. HDMI IN: HDMI® port for connecting the video source device.

4. Tx/Rx: 3-pin Phoenix block terminal connector for connecting an RS-232 control

device (PC) or a device to be controlled by RS-232 commands.

5. IR IN: 3.5mm jack for connecting an IR receiver (not included).

6. IR OUT: 3.5mm jack for connecting an IR emitter (not included).

CTRL

UPDATE B UPDATE A

Tx Rx DC 12V

IROUT

IRIN

HDBT OUT

HDMIIN

12345678

7. HDBT OUT: RJ45 jack for connecting a Cat6 Ethernet cable for

transmission/reception of the signals.

8. DC 12V: DC barrel connector for connecting the included AC power adapter.

Receiver

1. MODE SWITCH: Put the Mode switch in the CTRL position for normal operation and

to allow RS-232 control pass-through. Put the switch in the UPDATE A position to

update the Valens IC program. Finally, put the switch in the UPDATE B position to

update the compression IC program.

2. POWER LED: The LED illuminates red when power is applied.

3. HDMI OUT: HDMI® port for connecting the display.

4. Tx/Rx: 3-pin Phoenix block terminal connector for connecting an RS-232 control

device (PC) or a device to be controlled by RS-232 commands.

5. IR IN: 3.5mm jack for connecting an IR receiver (not included).

6. IR OUT: 3.5mm jack for connecting an IR emitter (not included).

7. HDBT IN: RJ45 jack for connecting a Cat6 Ethernet cable for transmission/reception

of the signals.

8. DC 12V: DC barrel connector for connecting the included AC power adapter.

CTRL

UPDATE B UPDATE A

DC 12V

Tx Rx

HDMIOUT

HDBT IN

IROUT

IRIN

12345678

SAMPLE CONNECTION DIAGRAM

1. Ensure that all equipment to be connected is powered off and unplugged from its

power source.

2. Place or mount the transmitter and receiver in their intended locations.

3. Using a High Speed HDMI® Cable (not included), plug one end into the HDMI input

on your display, then plug the other end into the HDMI OUT port on the receiver.

4. Using a Cat6 Ethernet cable of the appropriate length, plug one end into the HDBT

IN jack on the receiver, then plug the other end into the HDBT OUT jack on the

transmitter. Note that if this cable must be rated for in-wall use if it will be run

through the walls.

5. Using a High Speed HDMI Cable (not included), plug one end into the HDMI IN port

on the transmitter, then plug the other end into the HDMI output on your video

source device.

6. (Optional) If you want to control the video source device from the remote location,

plug an IR receiver (not included) into the IR IN jack on the receiver and position it

where it can receive IR signals from the remote control, then plug an IR emitter (not

IR Emitter

4K Blu-RayLaptop

TV Remote

Receiver

Transmitter Receiver

Emitter

HDTV

Blu-Ray

Remote

HDMI:

IR:

RS232:

CATx:

Power:

4K 40m,1080P 70m

PoC

Receiver

included) into the IR OUT jack on the transmitter and position it where it can

transmit IR signals to the video source device.

7. (Optional) If you want to control the display from the source location, plug an IR

receiver (not included) into the IR IN jack on the transmitter and position it where it

can receive IR signals from the remote control, then plug an IR emitter (not

included) into the IR OUT jack on the receiver and position it where it can transmit

IR signals to the display.

8. (Optional) If you want to control a remote RS-232 controlled device, plug the

included RS-232 cable into the Tx/Rx Phoenix connector on either the transmitter or

receiver, then plug the other end into the RS-232 connector on your PC. Next, plug a

second RS-232 cable (not included) into the Tx/Rx Phoenix connector on either the

transmitter or receiver, then plug the other end into the RS-232 connector on the

device you want to control.

9. Plug the DC barrel connector on the included AC power adapter into the DC 12V

jack o either the transmitter or receiver, then plug the other end into a nearby AC

power outlet. The POWER LEDs on both the transmitter and receiver should

illuminate red, indicating that power has been applied.

10. 10 Plug in and power on all connected equipment. Start playback on your video

source device and verify that video can be seen on the display. If you are using the

IR extension feature, verify that the appropriate devices can be controlled from the

remote location.

TECHNICAL SUPPORT

Monoprice is pleased to provide free, live, online technical support to assist you with any

questions you may have about installation, setup, troubleshooting, or product

recommendations. If you ever need assistance with your new product, please come online

to talk to one of our friendly and knowledgeable Tech Support Associates. Technical

support is available through the online chat button on our website www.monoprice.com

during regular business hours, 7 days a week. You can also get assistance through email by

sending a message to tech@monoprice.com

SPECIFICATIONS

Model

30446

Maximum Video Resolution

4K@60Hz 4:4:4

Bandwidth

18 Gbps

HDMI® Version

2.0

HDCP Version

2.2

Transmission Distance

1080p@60Hz: up to 229 feet (70 meters)

4K@60Hz: up to 131 feet (40 meters)

Input Power

12 VDC, 2A

AC Adapter Input Power

100 ~ 240 VAC, 50/60 Hz

Maximum Power Consumption

14 watts

Operating Temperature

+32 ~ +104°F (0 ~ +40°C)

Storage Temperature

+14 ~ +122°F (-10 ~ +50°C)

Operating Humidity

0 ~ 90% RH, non-condensing

Dimensions (each)

4.5" x 3.3" x 0.6" (115 x 84 x 16 mm)

Transmitter Weight

5.3 oz. (150 g)

Receiver Weight

5.4 oz. (153 g)

Blackbird™ is a trademark of Monoprice Inc.

HDBaseT™ and the HDBaseT Alliance logo are trademarks of the HDBaseT Alliance.

HDMI®, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or

registered trademarks of HDMI Licensing LLC in the United States and other countries.

Blu-ray Disc™ and Blu-ray™ are trademarks of the Blu-ray Disc Association.

Inhaltsverzeichnis

Andere Monoprice Extender Handbücher

Monoprice

Monoprice Blackbird 4K Pro HDBaseT Bedienungsanleitung

Monoprice

Monoprice 27841 Bedienungsanleitung

Monoprice

Monoprice Blackbird Pro WiHD 16049 Bedienungsanleitung

Monoprice

Monoprice DVI-LH Bedienungsanleitung

Monoprice

Monoprice MIR-500 Bedienungsanleitung

Monoprice

Monoprice 21793 Bedienungsanleitung

Monoprice

Monoprice MIR-300 Bedienungsanleitung

Monoprice

Monoprice Blackbird 21608 Bedienungsanleitung

Monoprice

Monoprice RS232-L Bedienungsanleitung

Monoprice

Monoprice Blackbird Pro WiHD 39625 Bedienungsanleitung

Monoprice

Monoprice KVM-LII Bedienungsanleitung

Monoprice

Monoprice Blackbird Bedienungsanleitung

Monoprice

Monoprice IR-320 Bedienungsanleitung

Monoprice

Monoprice 31055 Bedienungsanleitung

Monoprice

Monoprice 18784 Bedienungsanleitung

Monoprice

Monoprice 21905 Bedienungsanleitung

Monoprice

Monoprice HDMI-LH Bedienungsanleitung

Monoprice

Monoprice Blackbird 24279 Bedienungsanleitung

Monoprice

Monoprice 10247 Bedienungsanleitung

Monoprice

Monoprice 24281 Bedienungsanleitung

Monoprice

Monoprice 10224 Bedienungsanleitung

Monoprice

Monoprice blackbird 24181 Bedienungsanleitung

Monoprice

Monoprice BLACKBIRD 44570 Bedienungsanleitung

Monoprice

Monoprice BitPath AV 16227 Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Marmitek

Marmitek MegaView70 Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung