Monoprice Blackbird30916 Bedienungsanleitung

Blackbird™ 4K HDMI® 4x4 Mini Matrix

P/N 30916

User's Manual

SAFETY WARNINGS AND GUIDELINES

Please read this entire manual before using this device, paying extra attention to these

safety warnings and guidelines. Please keep this manual in a safe place for future reference.

This device is intended for indoor use only.

Do not expose this device to water or moisture of any kind. Do not place drinks or

other containers with moisture on or near the device. If moisture does get in or on

the device, immediately unplug it from the power outlet and allow it to fully dry

before reapplying power.

Do not expose this device to excessively high temperatures. Do not place it in, on,

or near heat sources, such as a fireplace, stove, radiator, etc. Do not leave it in direct

sunlight.

Do not place or install this device in an area where it can be exposed to excessive

amounts of dust, humidity, oil, smoke, or combustible vapors.

Prior to operation, check the unit and power cord for physical damage. Do not use if

physical damage has occurred.

Before plugging the unit into a power outlet, ensure that the outlet provides the

same type and level of power required by the device.

Never unplug the unit by pulling on the power cord. Always grasp the connector

head or adapter body.

Ensure that power is turned off and disconnected before making any electrical

connections.

Take care to prevent damage to the power cord. Do not allow it to become

crimped, pinched, walked on, or become tangled with other cords. Ensure that the

power cord does not present a tripping hazard.

Clean using a soft, dry cloth only. Do not use chemical cleaners, solvents, or

detergents. For stubborn deposits, moisten the cloth with warm water.

This device has no user serviceable parts. Do not attempt to open, service, or

modify this device.

INTRODUCTION

This 4x4 HDMI® Matrix allows you to distribute any of up to four HDMI video sources to

any of up to four HDMI displays. It supports resolutions up to 4K@60Hz YUV 4:4:4 and high

definition, multichannel audio formats, such as Dolby TrueHD™ and DTS-HD Master

Audio™. It can be controlled using buttons on the front panel, the included IR remote

control, or RS-232 control from a computer.

FEATURES

Distributes any of up to four HDMI® video sources to any of four HDMI displays

Supports HDMI 3D formats at resolutions up to 4K@30Hz

Compliant with the HDMI 2.0 and HDCP 2.2 specifications

Supports 24-bit RGB, YCbCr 4:4:4, and YCbCr 4:2:2 color spaces, as well as 12-bit

YCbCr 4:2:0

Supports high resolution, multichannel audio formats, such as Dolby TrueHD™ and

DTS-HD Master Audio™

CUSTOMER SERVICE

The Monoprice Customer Service department is dedicated to ensuring that your ordering,

purchasing, and delivery experience is second to none. If you have any problem with your

order, please give us an opportunity to make it right. You can contact a Monoprice

Customer Service representative through the Live Chat link on our website

www.monoprice.com during normal business hours (Mon-Fri: 5am-7pm PT, Sat-Sun: 9am-

6pm PT) or via email at [email protected]

PACKAGE CONTENTS

Please take an inventory of the package contents to ensure you have all the items listed

below. If anything is missing or damaged, please contact Monoprice Customer Service for a

replacement.

1x 4x4 HDMI® matrix

1x IR remote control

1x AC power adapter

1x User's manual

PRODUCT OVERVIEW

Front Panel

1. Power LED: The LED illuminates when the matrix is powered off. The LED is off when

the unit is powered on.

2. Digital Display: The four digits display the number (1-4) of the video input for each

letter (A-D) of the video output.

3. POWER: Press the POWER switch to turn the unit on or off.

4. OUT X: Press the OUT X buttons to cycle through the available inputs for the

selected output. The digital display will respond by showing the number (1-4) of the

input under the letter of the output (A-D).

Rear Panel

1. OUT X: HDMI® connectors for connecting up to four HDMI displays.

2. IN X: HDMI connectors for connecting up to four HDMI source devices.

3. RS-232: Phoenix connector for connecting a PC for RS-232 remote control.

4. EDID: DIP switches for setting the Extended Display Identification Data (EDID),

which determines the resolution and audio settings for the input source devices.

5. DC 12V: DC barrel connector for attaching the included AC power adapter.

Remote Control

1. Power: Press the Power button to turn the unit on or

off.

2. Output X: Each Output section of buttons contains 4

number buttons and two arrow buttons. Press a

number button to directly assign the numbered input

(1-4) to the lettered output (A-D). Press the Left Arrow

button to cycle backwards through the list of

numbered inputs. Press the Right Arrow button the

cycle forwards through the list of numbered inputs.

SAMPLE CONNECTION DIAGRAM

INSTALLATION

Perform the following steps to install this matrix into your home theater system.

1. Ensure that all equipment to be connected is powered off and unplugged from its

power source.

2. Place or mount the matrix in its intended location.

3. Using a High Speed HDMI® Cable (not included), plug one end into the HDMI input

on one of your displays, then plug the other end into one of the OUT ports on the

matrix. Repeat for up to three additional displays.

4. Using a High Speed HDMI® Cable (not included), plug one end into one of the IN

ports on the matrix, then plug the other end into the HDMI output on one of your

HDMI video source devices. Repeat for up to three additional HDMI video source

devices.

5. (Optional) Using a 3-pin Phoenix connector (not included) and a DE-9 (DB-9) D-

subminiature connector, wire it for RS-232 transmission and reception, then plug

the Phoenix connector into the RS-232 connector and plug the D-sub connector

into one of the RS-232 serial outputs on your computer. The specific details of this

step will vary with your computer and its serial connectors. See the

RS-232

CONTROL

section below for connection details.

6. Set the EDID DIP switches for the maximum video resolution and audio capabilities

of the least capable connected display. See the

EDID DIP SWITCHES

section below

for details.

7. Plug the DC barrel connector on the included AC power adapter into the DC 12V

jack on the matrix, then plug the adapter into a nearby AC power outlet. The Power

LED will illuminate, indicating that the matrix is in standby mode.

8. Press the POWER button to turn the matrix on. The Power LED will extinguish,

indicating that power is applied.

9. Plug in and power on all connected equipment. Start video playback on all video

sources. Verify that video can be seen on each display.

10. Press each OUT button on the front panel four times to verify that the video on the

indicated display switches to the indicated video source.

Congratulations, you have successfully installed this Blackbird™ HDMI® matrix.

EDID DIP SWITCHES

The Extended Display Identification Data (EDID) is the means by which the video source

devices know the maximum video and audio capabilities of the connected display. Since

this matrix can connect four displays, each of which may have different capabilities, the

EDID DIP switches are used to set the maximum video and audio settings to that of the

least capable display.

For example, if you have 4K, 1080p, and 720p displays connected, the maximum common

video resolution is 720p, so you need to set the EDID DIP switches to set the maximum

video resolution to 720p.

The following table shows the various DIP switch settings for each of the different video

and audio combinations.

DIP Switches

Video Setting

Audio Setting

0000

1080p@60Hz

2.0 channel stereo

0001

1080p@60Hz

5.1 channel Dolby®/DTS®

0010

1080p@60Hz

7.1 channel HD audio

0011

1080i@60Hz

2.0 channel stereo

0100

1080i@60Hz

5.1 channel Dolby/DTS

0101

1080i@60Hz

7.1 channel HD audio

0110

3D@60Hz

2.0 channel stereo

0111

3D@60Hz

5.1 channel Dolby/DTS

1000

3D@60Hz

7.1 channel HD audio

1001

4K@30Hz YCbCr 4:4:4

2.0 channel stereo

1010

4K@30Hz YCbCr 4:4:4

5.1 channel Dolby/DTS

1011

4K@30Hz YCbCr 4:4:4

7.1 channel HD audio

1100

4K@60Hz YCbCr 4:4:4

2.0 channel stereo

1101

4K@60Hz YCbCr 4:4:4

5.1 channel Dolby/DTS

1110

4K@60Hz YCbCr 4:4:4

7.1 channel HD audio

1111

EDID is controlled by a computer via an RS-232 connection

RS-232 CONTROL

This matrix can be controlled from a computer using an RS-232 serial data connection.

When you make the physical serial connection, you will be able to see the matrix on your

PC as a USB device. If it is not already powered on, press the POWER button on the front

panel to power on the matrix.

Next, use your file browser to copy the 4x4 HDMI Matrix Controller.exe software program

from the matrix to your PC, then double-click the program to run the RS-232 control

program. The following sections detail each page in the program.

General Page

The General Page allows you to set the basic communications settings to connect with the

matrix.

1. Port: Use the drop-down list to select the RS-232 COM port that is connected to the

matrix.

2. Connect: Click the Connect button to connect the PC with the matrix.

3. Factory Reset: Click the Factory Reset button to reset the matrix to the factory

default settings.

4. Reboot: Click the Reboot button to restart the matrix.

5. Enable Beep: Click the Enable Beep checkbox to enable or disable audio feedback

from the matrix.

6. Power On: Click the Power On checkbox to turn the matrix on or off.

7. Status: Click the Status button to refresh the matrix status.

8. Clear: Click the Clear button to clear all device information.

9. Device Information: Information about the device is displayed in this section.

EDID Page

Rather than using the general physical EDID settings, you can individually set the EDID for

each input. This can be done in three ways: manually selecting the EDID mode, copying the

EDID data from a particular display, or reading all EDID information from a file. Note that to

use this program, the EDID DIP switches must be set to 1111.

1. Set EDID Mode: Use the first drop-down list to select the EDID capabilities, then use

the second drop-down list the select the video source device, and finally click the

Set button to assign the EDID capabilities.

Inhaltsverzeichnis

Andere Monoprice Matrix-Umschalter Handbücher

Monoprice

Monoprice Blackbird 39670 Bedienungsanleitung

Monoprice

Monoprice Blackbird 39665 Bedienungsanleitung

Monoprice

Monoprice Blackbird 39669 Bedienungsanleitung

Monoprice

Monoprice Blackbird 15376 Bedienungsanleitung

Monoprice

Monoprice Blackbird 44557 Bedienungsanleitung

Monoprice

Monoprice HDX-420X Bedienungsanleitung

Monoprice

Monoprice Blackbird 44568 Bedienungsanleitung

Monoprice

Monoprice 39668 Bedienungsanleitung

Monoprice

Monoprice Blackbird 39665 Bedienungsanleitung

Monoprice

Monoprice 21818 Bedienungsanleitung

Monoprice

Monoprice Blackbird 15377 Bedienungsanleitung

Monoprice

Monoprice HDMX-402 Bedienungsanleitung

Monoprice

Monoprice 24179 Bedienungsanleitung

Monoprice

Monoprice Blackbird 15376 Bedienungsanleitung

Monoprice

Monoprice 39668 Bedienungsanleitung

Monoprice

Monoprice Blackbird 39667 Bedienungsanleitung

Monoprice

Monoprice Blackbird 27842 Bedienungsanleitung

Beliebte Matrix-Umschalter Handbücher anderer Marken

Broadcast Tools

Broadcast Tools SS 8.2 Bedienungsanleitung

Altimium

Altimium MATF32 Bedienungsanleitung

ALFAtron

ALFAtron ALF-MUK44N Bedienungsanleitung

Kramer

Kramer XL 3216VS Bedienungsanleitung

PTN

PTN FMX12 Bedienungsanleitung

CYP

CYP nT15GX01 Bedienungsanleitung

Kramer

Kramer VP-2x2 Bedienungsanleitung

Kramer

Kramer Sierra Video 6432V5xl Bedienungsanleitung

TESmart

TESmart HMA0402A40 Bedienungsanleitung

Octava

Octava HD4XSTPMX Bedienungsanleitung

Intelix

Intelix FLX-88 Betriebsanleitung

Kramer

Kramer LASSEN XL 3232S Bedienungsanleitung

Roland

Roland XS-1HD Bedienungsanleitung

Kramer

Kramer VS-66HDCPxl Bedienungsanleitung

Atlona

Atlona AT-HDMI-22M Bedienungsanleitung

Link

Link HD8X8 Bedienungsanleitung

AMX

AMX AVS-OP-2020-117 Anleitungen und Rezepte

Lindy

Lindy 38042 Bedienungsanleitung