MONSTERMOUNT MB-1003 Bedienungsanleitung
MB1003
Installation instructions
Руководство пользователя
LCD Wall Mount
Кронштейн для LCD
ENG
2
Hardware Kit
We thank you for choosing Monster Mount production, which will help
you to solve problems of accommodation of home appliances effec-
tively. Monster Mount offers a full spectrum of highquality wall, ceiling,
floor mounts, which will stylishly supplement your house.
Safety Warning
1. Make sure these instructions are read and thoroughly understood before
attempting installation. If you are unsure of any part of this installation, contact
a professional installer for assistance.
2. The wall or mounting surface must be capable of supporting the combined
weight of the mount and the display; otherwise the structure must be rein-
forced.
3. Safety gear and proper tools must be used. Failure to do so can result in prop-
erty damage and/or serious injury. A minimum of two people are required for this
installation. Do not attempt to install this mount alone under any circumstance.
4. Follow all instructions and recommendations regarding adequate ventilation
and suitable locations for mounting your display. Consult the owner‘s manual
for your display for more information.
Specifications
Display Size: 15–27" (38–69 см)
Profile: 1.6” (4.0 cm)
Mounting Pattern: 75 mm x 75 mm and 100 mm x 100 mm
Maximum Load: 11 kg (25 lbs)
Tilt Range: up to 20.0° down
Box Contents
Mount (x1) Instruction Manual (x1)
Wall Plate (x1) Hardware Kit (x1)
Required Tools
Head Screw Driver, Electric or Portable Drill, 3 mm (1/8”) Drill Bit and Stud
Finder for Drywall Installation, 8 mm (5/16”) Masonry Bit for Concrete
Installation, Level.
ENG
3
STEP 1A Mounting to the Wall (Drywall)
IMPORTANT! For safety reasons, this mount must be secured to a wood stud
capable of supporting the combined weight of the mount and display. Do not
mount to drywall alone.
1. Use a high quality stud finder to locate a stud where you wish to install your
mount. Mark both edges of the stud to help identify the exact center.
NOTE: You must use the center of the stud to avoid cracking or splitting the
wood during installation.
2. Place the wall plate against the wall over the marked stud. Make sure it is
level.
3. Mark the two locations for securing the wall plate and set the wall plate aside
(see Fig. 1).
4. Drill a 3 mm (1/8”) pilot hole at each marked location.
5. Place the wall plate back against the wall and attach it using the drywall
screws (A) provided (see Fig. 2). Do not over-tighten these screws. Ensure
that the wall plate remains level after both screws are secured.
Fig. 1
Fig. 2
ENG
4
Mounting to the Wall (Concrete)
IMPORTANT! For safety reasons, the concrete wall must be capable of sup-
porting the combined weight of the mount and the display. The manufacturer
takes no responsibility for failure caused by walls of insufficient strength.
1. Place the wall plate against the wall in the desired location. Make sure it is
level.
2. Mark the two locations for securing the wall plate (see Fig. 3) and set the wall
plate aside.
3. Drill an 8 mm (5/16”) hole at each marked location. Remove any excess dust
from the holes.
4. Insert a concrete anchor (B) into each hole so that it is flush with the concrete
surface (see Fig. 4). A hammer can be used to lightly tap the anchors into place
if necessary.
NOTE: If the concrete wall is covered by a layer of plaster or drywall, the con-
crete anchor must pass completely through the layer to rest flush with the
concrete surface.
5. Place the wall plate back against the wall and attach it using the drywall
screws (A) provided. Do not over-tighten these screws. Ensure that the wall
plate remains level after both screws are secured.
STEP 1B
Fig. 3
Fig. 4
ENG
5
STEP 2 Attaching the Mount to the Display
IMPORTANT! Use extra care during this part of the installation. If possible,
avoid placing your display facedown as it may damage the viewing surface.
NOTE: This mount comes with a selection of different screw diameters and
lengths to accommodate a wide variety of display models. Not all of the hard-
ware in the kit will be used. If you cannot find the appropriate screw size in the
kit provided, consult the manufacturer of your display for more information.
1. Determine the correct length of screw to use by examining the back of your
display:
a) If the back of your display is flat and the mounting holes are flush with the
surface, you will use the M4 x 12 screws (C) from the hardware kit.
b) If the back of your display is curved, has a protrusion, or if the mounting
holes are recessed, you will need to use the M4 x 20 screws (D) and may also
need to use the spacers (E).
2. Attach the display plate to the back of your display using the screws identi-
fied in step 1. If you are using the M4 x 20 screws on a display with a curved or
recessed back, you may also need to use the spacers (E) (see Fig. 5). However,
you should only use a spacer if necessary.
NOTE: If the holes of the mount do not line up with the holes on your display,
check to make sure that your display is VESA compatible. This mount can only
be used with displays that are VESA 75 or VESA 100 compatible. Consult the
manufacturer of your display for more information.
Fig. 5
For displays
with flat backs
For displays
with curved or
recessed backs
ENG
6
STEP 3 Final Assembly
1. Make sure safety device is unlocked. If locked,
simply pull down on the cord until you hear a click.
2. Carefully slide the mount with your display
attached into the wall plate (see Fig. 6). Do not
release the display until the display plate is
securely placed on the wall plate.
3. Pull down on the cord until you hear a click to
lock the mount to the wall plate.
IMPORTANT! The mount must be in the locked
position at all times to prevent the display from
being accidentally lifted from the wall plate.
Operation and Adjustment
1. To adjust the tilt angle, hold the display firmly in place while pulling down on
the white cord. Carefully allow the display to move to the lowest position before
releasing the cord. The display can be left in the lowest position or pushed into
one of three additional tilt positions as desired.
2. Periodically clean your mount with a dry cloth. Inspect all screws and hard-
ware at regular intervals to ensure that no connections have become loose over
time. Retighten as needed.
Fig. 6
WARRANTY
Monster Mount is liable for unit quality and functions and guarantees
that the unit is free from production defects for the period of 3 years
after sales date. In case any defects will occur during warranty period,
Monster Mount will replace the unit free of charge under below terms
and conditions.
WARRANTY TERMS
1. Defected unit has to be returned to the sales point, where it was
bought. Transportation fees, which can occur to return the unit back to
sales point, are on buyer's account.
2. Any claims under warranty can be made only upon purchase receipt
presentation.
3. Warranty is not valid in case of:
the unit was assembled not in accordance with installation
instructions;
repair or modification was done by companies, without Monster
Mount authorization;
defect appeared due to fire, flood, lightning, deforming cleaning,
extremely high temperature, solvent, acids, wrong use or careless
terms;
the products have been lost, damaged by misuse, abuse or acci-
dent.
Monster Mount shall not be responsible or liable for injuries or property
damage, direct, indirect or consequential, which may arise from the
inability to use this product safety properly, and in the manner for which
it has been designed and manufactured.
Product can be used within 10 years at least.
РУС
9
Благодарим Вас за выбор продукции Monster Mount, которая помо-
жет эффективно решить проблемы размещения бытовой техники.
Monster Mount предоставляет полный спектр высококачественных
настенных, потолочных, напольных кронштейнов, которые станут
стильным дополнением Вашего интерьера.
Внимание!
1. Перед началом установки убедитесь, что Вы правильно прочитали и
поняли данную инструкцию. Если Вы не уверены в каком-либо этапе уста-
новки, свяжитесь со специалистом.
2. Стена или поверхность для установки должна выдерживать вес и опоры,
и дисплея; в ином случае ее структуру следует укрепить.
3. При установке должны быть использованы исправные инструменты. В
процессе установки рекомендуется участвовать двум лицам.
Использование неисправного инструмента и/или попытка установки
одним человеком может привести к порче имущества и травмам.
4. Следуйте всем инструкциям и рекомендациям в отношении необходи-
мой вентиляции и подходящего месторасположения для установки
Вашего дисплея. Обращайтесь к Руководству пользователя Вашего дис-
плея для получения большей информации.
Технические характеристики
Размер дисплея: 38–69 см (15–27")
Расстояние от стены: 4.0 см (1.6”)
Крепежная схема: 75 мм х 75 мм или 100 мм х 100 мм
Максимальная нагрузка: 11 кг
Диапазон наклона: до 20° вниз
Комплектация
Настенная панель (х1) Крепежная пластина (х1)
Руководство пользователя (х1) Монтажный набор (х1)
Необходимое оборудование
Крестообразная отвертка, портативная либо электрическая дрель, сверло
1/8” (3 мм) и инструмент для поиска направляющих (в случае установки на
стены сухой кладки), победитовое сверло 5/16” (8 мм) (в случае установки
на бетонные стены или стены каменной кладки), пузырьковый уровень.
Комплект крепежных деталей
Настенный монтаж (гипсокартон/дерево)
Внимание! В целях безопасности данный кронштейн должен крепиться к
Внимание! В целях безопасности, данный кронштейн должен крепиться к
деревянной/гипсокартонной направляющей, способной выдержать сум-
марный вес кронштейна и дисплея. Не устанавливайте кронштейн в оди-
ночку.
1. Используйте высококачественный инструмент для поиска направляю-
щих в том месте, где Вы впоследствии хотели бы расположить Ваш крон-
штейн. Отметьте края направляющей, чтобы точно определить ее центр.
Примечание. В процессе установки придерживайтесь центра направля-
ющей, чтобы избежать растрескивания, а также последующего разруше-
ния дерева/гипсокартона.
2. Поместите настенную панель на выбранное Вами место и выровняйте ее.
3. Отметьте точками два места, предназначенные для крепления крон-
штейна на стену (см. рис. 1), и отложите настенную часть кронштейна в
сторону.
4. Просверлите отверстия диаметром 3 мм (1/8”) в каждом отмеченном
месте.
5. Поместите настенную часть кронштейна обратно на стену и закрепите
ее с помощью шурупов для гипсокартона/дерева (A), идущих в комплекте
(см. рис. 2). Не перетягивайте шурупы. Убедитесь, что кронштейн
остался на том же уровне после завершения Вами всех вышеуказанных в
части 1A действий.
РУС
10
ШАГ 1A
Рис. 1
Рис. 2
Ш
Inhaltsverzeichnis
Sprachen:
Andere MONSTERMOUNT Rack & Stand Handbücher
Beliebte Rack & Stand Handbücher anderer Marken
Salamander
Salamander Acadia AC/W/L400/WH Bedienungsanleitung
Fohhn
Fohhn VAT-09 Benutzerhandbuch
ricoo
ricoo FS0522 Bedienungsanleitung
AMSOIL
AMSOIL BMK-22 Kurzanleitung
Kargo Master
Kargo Master 48220 Bedienungsanleitung
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung
