Monstertech MTX HOTAS Bedienungsanleitung

MTX HOTAS

Instruction Manual EN

MTX HOTAS INSTRUCTION MANUAL MTX HOTAS INSTRUCTION MANUAL

2 3

1 General information

This guide is meant to help you assemble your Sim Rig as smoothly as possible. If you still

have questions about the assembly process, please contact [email protected] or support@

monstertechusa.com.

1.1 Before you start

Before you start the assembly, we are going to look at some common assembly steps and of-

ten used parts, as well as required tools.

1.1.1 Required Tools

For our assembly, we need following tools*:

- Hex key set with ball head with extension

- Rubber or plastic mallet

- Flat head screwdriver

- Tape measure w/ millimeters

*Tools are not included with the Sim Rig

1.1.2 Inserting T-Nut into Profile

There are two ways to insert the M8 T-Nuts into the respective prole groove; refer to Figure 1

and 2 respectively.

Figure 1: Slide in from side

Figure 2: Rotate in from top

MTX HOTAS INSTRUCTION MANUAL MTX HOTAS INSTRUCTION MANUAL

4 5

1.1.3 Universal Fastener Assembly

The universal fastener assembly can be prepared the following way, so long as the T-Nut can

be slid in from the side. One Universal Fastener Assembly is made up from one (1) M8x30 Hex

Screw, one (1) T-Nut, and one (1) Universal Fastener.

Figure 3: Universal fastener assembly

If inserting the universal fastener assembly from the side is not possible, it is necessary to rota-

te the T-Nut into the prole groove rst, and then screw the M8x30 bolt (along with the univer-

sal fastener) into the T-Nut.

1.1.4 Angle Bracket Stud Removal

Sometimes it might be necessary to break off the studs from angle brackets (if those are part

of the product). This is best achieved by:

1. Inserting a at-head screwdriver between the stud and the bracket, and then

2. Rotate the screwdriver for the stud to come off

MTX HOTAS INSTRUCTION MANUAL MTX HOTAS INSTRUCTION MANUAL

6 7

1.1.5 Angle Bracket Assembly

For some assemblies the use of angle brackets is required. These are prepared by using two

(2) M8x18 hex screws, two (2) washers, and two T-Nuts.

Figure 5: Angle bracket assembly

1.1.6 Adjustment of Profile Feet

The prole feet are installed on the MTX HOTAS or MTX Stand-Alone TV

Figure 6: Prole feet

2 Overview

2.1 Completed MTX HOTAS

HOTAS - Overview

Figure 8:

Use the above image as reference for the following assembly inst-

ructions.

MTX HOTAS INSTRUCTION MANUAL MTX HOTAS INSTRUCTION MANUAL

8 9

3.1

Figure 9: HOTAS assembly - step 1

3.2

Figure 10: HOTAS assembly - step 2

3.3

Figure 11: HOTAS assembly - step 3

3.4

Figure 12: HOTAS assembly - step 4

MTX HOTAS INSTRUCTION MANUAL MTX HOTAS INSTRUCTION MANUAL

10 11

3.5

Figure 13: HOTAS assembly - step 5

3.6

Figure 14: HOTAS assembly - step 6

3.7

Figure 15: HOTAS assembly - step 7

3.8

Figure 16: HOTAS assembly - step 8

Attention: Please use the in-

cluded grey corner brackets

instead of the clamps.

Achtung: Bitte die grauen

Winkel anstatt die Klemmhe-

bel verwenden.

Attention: Please use the in-

cluded grey corner brackets

instead of the clamps.

Achtung: Bitte die grauen

Winkel anstatt die Klemmhe-

bel verwenden.

MTX HOTAS INSTRUCTION MANUAL MTX HOTAS INSTRUCTION MANUAL

12 13

3.9

Figure 17: HOTAS assembly - step 9

3.10

Figure 18: HOTAS assembly - step 10

3.11

Figure 19: HOTAS assembly - step 11

3.12

Figure 20: HOTAS assembly - step 12

MTX HOTAS INSTRUCTION MANUAL MTX HOTAS INSTRUCTION MANUAL

14 15

3.13

Figure 21: HOTAS assembly - step 13

WARNHINWEISE

GEFAHR: Nicht für Kinder unter 3 Jahren,

Kleinteile - Verschluckungsgefahr!

Nur für Kinder ab 12 Jahren und Erwachsene

Alle MONSTERTECH Produkte sind handgefertigt und

qualitätsgeprüft.

Das Rennsitzgestell ist zur Verwendung in Kombination mit

einem Autositz und nur zur Verwendung im Innenbereich

ausgelegt.

Wir übernehmen keine Haftung für zweckentfremdete

Benutzung.

Bei Fragen zur Sicherheit oder Aufbau des Rennsitzgestells,

wenden Sie sich an info@monstertech.de oder besuchen

unsere Website unter www.monstertech.de.

WARNING NOTICES

NOTE: Contains small parts not suitable for children under 3

years.

Only suitable for children over 12 years and adults.

All MONSTERTECH products are handmade and quality

checked.

The racing frame is only designed for inside usage in

combination with a car seat.

We exclude liability if the product is used for purposes other

than intended.

If you have safety concerns or questions regarding assembly,

www.monstertech.de.

Inhaltsverzeichnis

Andere Monstertech Rack & Stand Handbücher

Monstertech

Monstertech MFD/TABLET MOUNT CENTER Bedienungsanleitung

Monstertech

Monstertech Wall Holder Bedienungsanleitung

Monstertech

Monstertech FLIGHT STAND Bedienungsanleitung

Monstertech

Monstertech STAND Bedienungsanleitung

Monstertech

Monstertech MFD Bedienungsanleitung

Monstertech

Monstertech CHAIR MOUNT KEYBOARD TRAY Bedienungsanleitung

Monstertech

Monstertech JOYSTICK/HOTAS TABLE MOUNT Bedienungsanleitung

Monstertech

Monstertech MTS CENTER JOYSTICK Bedienungsanleitung

Monstertech

Monstertech CHAIR MOUNT INSTRUMENT CARRIER Bedienungsanleitung

Monstertech

Monstertech CHAIR MOUNT UNIVERSAL BASE Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung