Morphy Richards IB42700 Bedienungsanleitung

This guarantee is valid in the UK and Ireland

only. It is in your interest to retain the retailers receipt as

proof of purchase. Please quote the following information

if the product develops a fault. These numbers can be

found on the base of the product.

Model No. Serial No.

All Morphy Richards Products are individually tested

before leaving the factory. In the unlikely event of any

appliance proving to be faulty within 28 days of purchase it

should be returned to the place of purchase for it to be

replaced.

If the fault develops after 28 days and within 24

months of original purchase, you should contact the

helpline number quoting Model number and Serial number

on the product, or write to the address below. You will

be asked to return the product (in secure, adequate

packaging) to the address below along with a copy of proof

of purchase. Subject to the exclusions set out below (see

‘Exclusions’) the faulty appliance will then be repaired or

replaced and dispatched usually within 7 working days of

receipt.

If for any reason this item is replaced during the 2 year

guarantee period, the guarantee on the new item will be

calculated from original purchase date. Therefore it is vital

to retain your original till receipt or invoice to indicate the

date of initial purchase.

To qualify for the 2 year guarantee the appliance must

have been used according to the manufacturers

instructions. For example kettles should have been

regularly descaled or an iron cord should have been

stored as recommended by the instructions.

EXCLUSIONS

Morphy Richards shall not be liable to replace or

repair the goods under the terms of the Guarantee where:

1 The fault has been caused or is attributable to

accidental use, mis-use, negligent use or used contrary

to the manufacturers recommendations or where the

fault has been caused by power surges or damage

caused in transit.

2 The appliance has been used on a voltage supply other

than that stamped on the products.

3 Repairs have been attempted by persons other than

our service staff (or authorised dealer).

4 Where the appliance has been used for hire purposes

or non-domestic use.

5 Morphy Richards are not liable to carry out any type of

servicing work, under the guarantee.

6 Plastic filters for all Morphy Richards kettles and coffee

makers are not covered by the guarantee.

This guarantee does not confer any rights other than

those expressly set out above and does not cover any

claims for consequential loss or damage. This guarantee is

offered as an additional beneﬁt and does not affect your

statutory rights as a consumer.

The After Sales Division, Morphy Richards Ltd, Mexborough, South Yorkshire, England, S64 8AJ

Helpline (office hours): UK (local rate) 08450 777700, Republic of Ireland 1800 409119

Two year guarantee

Turbosteam iron

IMPORTANT

SAFEGUARDS

1Read all instructions.

2Use the iron only for its intended use.

3To protect against a risk of electric

shock, do not immerse the iron in

water or other liquids.

4The power socket should always be

switched off before plugging or

unplugging from outlet. Never yank

cord to disconnect from outlet;

instead, grasp plug and pull to

disconnect.

5Do not allow cord to touch hot

surfaces. Let iron cool completely

before putting away. Loop cord loosely

around iron when storing.

6Always disconnect iron from electrical

outlet when filling with water or

emptying, and when not in use.

7Do not operate the iron with a

damaged cord or if the iron has been

dropped or damaged. To avoid the risk

of electric shock, do not disassemble

the iron, but telephone Morphy

Richards for advice. Incorrect

reassembly can cause a risk of electric

shock when the iron is used.

8 Do not use the vertical steam

feature on clothes that are being

worn.

9 Place all electrical appliances out

of the reach of children. Close

supervision is necessary for an

appliance being used near children.

10Do not leave the iron unattended

whilst plugged in or on an ironing

board. Never allow the power cord

to overhang the work surface.

11Burns can occur from touching hot

metal parts, hot water or steam. Use

caution when you turn a steam iron

upside down - there may be hot water

in the reservoir.

SPECIAL

INSTRUCTIONS

1If your iron does not work, check the

following points:

Has the temperature control been set

to the required temperature? Is the

plug in its socket? Is the plug itself or

the socket faulty? (Check by plugging in

another appliance)

2 Warning: When in use, your iron

should never be placed flat and

left on an ironing board.

3To prevent damage to the textile being

ironed, follow the temperature guide

carefully. (Test the inside of the hem of

the garment).

4When ironing is complete, remove the

plug from the socket, empty any

remaining water from the tank, and

allow to cool before storing.

5If you drop or severely knock your

iron this could cause internal damage

even if the outside appears alright.

Have it checked by a qualified

electrician.

6It is recommended that you use up one

beaker of water by operating your

iron’s steam and shot of steam

functions before ironing any clothes as

some dripping may occur while your

iron’s steam system is activated.

SAVE THESE

INSTRUCTIONS

Electrical requirements

Check that the voltage on the rating plate of

your appliance corresponds with your house

electricity supply which must be A.C. (Alternating

Current).

If the socket outlets in your home are not

suitable for the plug supplied with this appliance,

the plug should be removed and the appropriate

one fitted.

WARNING: The plug removed from the

mains lead, if severed, must be destroyed as a

plug with bared flexible cord is hazardous if

engaged into a live socket outlet.

WARNING: THIS APPLIANCE MUST

BE EARTHED

Should the fuse in the 13 amp plug require

replacement, a BS1362 13 amp fuse must be

fitted.

Components of your

iron

⁄

Temperature control dial

Temperature indicator light

‹

Water tank cap

›

Soleplate

ﬁ

Spray button (certain models only)

ﬂ

Shot of steam button (certain models only)

‡

Steam on-off button/variable steam button

Instructions for use

Temperature Guide

Heat setting markings on the adjustable control dial of all Morphy Richards irons match those of

the International Textile Care Labelling Code.

⁄

‡

ﬁ‹ ﬂ

›

Symbol 67 8 9

(120°C Max) Cool (160°C Max) Warm (210°C Max) Hot

Control knob Do not iron ● ●● ●●●

positions at all

Fabric Nylon, Acetates Wool, Polyester Cotton, Linen

E.g. Acrilan mixtures e.g. Rayon, Rayon

Courtelle, Orlon, Polyester/Cotton mixtures,

Triacetates, e.g. e.g. Rayon/Linen

Tricel/Polyester

Ironing Iron on wrong side. Fabrics requiring

If moisture required this setting usually

use damp cloth require steam

(Not Acetate) pressing for heavy

cotton, denim etc

With water in tank Dry and Spray Steam/spray & shot

Jet clean

Without water in tank Dry ironing

4 4

Before use

Note: The Steam facility should only be used

on garments which are suitable for ironing at 2

and 3 dot settings. (Garments marked with 2 dot

recommendation should, if required, be ironed at

the lower end of the steam range).

Textiles and clothes are supposed to carry

ironing instructions. If they don’t you should

follow the temperature guide on page 3, but be

sure to test the temperature by ironing the hem

of the garment or similar area first. If you turn

the control dial down from a hot setting to a

cooler setting, wait until the iron temperature

has stabilised before you continue ironing.

Filling

Before filling your iron make sure that it is not

plugged in and ensure that the iron is in the

‘steam off’ position. To do this slide the steam

button to the ‘down’ position E/F.

Remove the water tank cap and hold the iron

by the handle. Fill using the beaker provided A.

Your iron has a large

capacity tank which can

hold 2 beakers of water.

After filling, replace the

water tank cap to prevent

any water escaping from

the tank during ironing B.

Your iron has been

specially designed for use

with tap water. Never use

battery topping up fluid or water containing any

substances such as starch or sugar, or defrosted

water from a refrigerator. In hard water areas

the use of distilled or demineralised water is

recommended. Warning: When filling your

iron with tap water always use your

beaker. Never fill directly under the tap.

Temperature control

Plug in the iron and

switch on. Set the

temperature control dial

C to the temperature

required, but don’t start

ironing immediately. If

you wait a few minutes,

the iron will stabilise at

the required setting.

Your Morphy Richards

iron is fitted with an indicator light which will go

on and off while your are ironing. This is

perfectly normal as it shows that the iron is

maintaining the heat setting you have chosen.

For the correct temperature always set the

control dial with the required setting at the

bottom of the dial nearest the back of the iron.

Features of your iron

Temperature indicator light

The temperature indicator light shows that

the iron is warming up. When the required

temperature is reached the light will go out and

will cycle on-off during operation.

Dry Ironing

You can use your iron as a dry iron only.

Make sure the steam control is off. Any

temperature setting may be used depending on

the garment. The spray feature (if fitted) may be

used provided there is water in the tank (see

filling section). The shot of steam feature (if

fitted) may also be used provided the

temperature control dial is set to the steam

range C. You do not need to put any water in

the tank when dry ironing only.

Spray (certain models only)

Press the spray button and aim spray of water

at stubborn creases. The grey region shows the

spray button on different models D. You can do

this whilst dry ironing providing there is water in

the tank. When using the water spray it may be

necessary to push the button a few times to get

the spray pump primed.

Steam ironing

Ensure that the temperature

control dial is set in the steam

range Cand that there is

water in the tank.

Rest the iron on its heel and

allow to heat up.

Before you start ironing,

slide the steam button up, to

the steam position E.

If you need to refill the

water tank during use, unplug

the iron and follow the filling

instructions taking care not to

spill any water over the iron.

Variable steam (certain

models only)

If your iron is fitted with variable steam, the

steam output can be varied from low to high.

Simply slide the variable steam button up or

down F.

The high position is for ironing

stubborn creases

The mid position is for normal

ironing

The low position switches the

steam off.

Shot of steam ironing

(certain models only)

Press the shot of steam

button Gto obtain a burst of

extra steam for ironing out

creases in heavy material such as

denim etc. The shot of steam

can be used whilst dry ironing,

providing there is water in the

tank and the temperature

control is set in the steam range.

Do not use shot of steam at

temperatures below the steam

range shown on the control.

Vertical steam facility (certain models

only)

Hold the iron in a vertical position between

1cm to 2cm away from the item H. Press the

shot of steam button G, this will create vertical

steam. This feature is especially useful for

removing creases from hanging clothes, curtains,

wall hangings, etc.

Auto shut-off (certain models only)

If your iron is an ‘auto shut-off’ model it will

automatically turn your iron off within 60

seconds of not being used. Grasping the iron by

its handle will turn it on again. If the iron is below

the temperature set on the temperature control

dial, the temperature indicator light will illuminate

until the iron reaches the set temperature.

AUTO SHUT-OFF IS NOT AN

ALTERNATIVE TO UNPLUGGING THE

IRON WHEN NOT IN USE.

Steam spray irons Steam spray shot irons

Steam on

Steam off

High steam

Low steam

Steam off

Emptying and storing

When you have finished ironing unplug your

iron. Ensure that the steam button is in the

‘Steam off’ position and empty any remaining

water out of the filler hole I. Remember to

replace the water tank cap before storing.

Do not store in the box, but in an upright

position, so that any drops of water remaining

cannot leak out and discolour the soleplate. Your

iron has a cable tidy feature.

Important: The flex can be

damaged if wound too tightly

around the iron after use. Make

a loose loop with the flex and

wrap it around the iron using

the cord clip to keep the flex in

place. The iron must be cool

before winding the flex and

storing on its heel J.

Maintenance

Jet cleaning

Shot of Steam models have a built in cleaning

system designed to keep the water tank, water

valve, steam chamber and steam vents clear of

lint and loose mineral deposits. The ‘Jet Clean’

should be operated after each period of ironing.

To operate - ensure there is a little water in the

tank, place the iron on its heel. Having turned the

temperature control dial to its maximum

position, wait for the indicator light to go out,

then unplug the iron and hold it about 6"

(150mm) above the sink in the ironing position

and push the shot of steam button G about 10

times in succession. After this cleaning operation,

empty out any remaining water.

To clean an aluminium soleplate

To keep the soleplate of your iron clean and

free of limescale, make a paste of mild scouring

powder and a little water. Apply a small amount

to the soleplate, rub and then remove with a

damp cloth. Wipe thoroughly with a clean cloth.

To clean a mirror finished soleplate

If your iron has been fitted with a polished or

mirror finished soleplate for easier ironing please

follow the cleaning instructions below:

To keep the soleplate of your iron clean and

free of limescale we recommend that you use

one of the gentle chrome or silver cleaners

generally available, and always follow the

manufacturers instructions on the container. To

clean off melted on man-made fibre set the iron

to the 3 dot position and pass it over a clean

piece of cotton which will draw the deposit off

the surface.

To clean a coated soleplate

In the unlikely event of any man-made fibre

fusing to the soleplate set the iron at the 3 dot

position and pass it over a clean piece of cotton

which will draw the deposit off the surface.

Do not use scouring powder or solution

as this could damage the coating.

To clean the exterior

Allow to cool and wipe over with a damp

soapy cloth, then dry with a clean dry cloth.

Morphy Richards Limited, Mexborough,

South Yorkshire, England S64 8AJ

Morphy Richards products are intended for household use only.

Morphy Richards has a policy of continuous improvement in product quality and design.

The Company, therefore, reserves the right to change the specification of its models at any time.

441/3752/06 Rev 3

Inhaltsverzeichnis

Andere Morphy Richards Eisen Handbücher

Morphy Richards

Morphy Richards 40684 Bedienungsanleitung

Morphy Richards

Morphy Richards TURBOSTEAM IRON - MANUAL 2 Bedienungsanleitung

Morphy Richards

Morphy Richards Power Steam Bedienungsanleitung

Morphy Richards

Morphy Richards Comfigrip 300007 Bedienungsanleitung

Morphy Richards

Morphy Richards Speed Steam Pro Bedienungsanleitung

Morphy Richards

Morphy Richards IB40620 Bedienungsanleitung

Morphy Richards

Morphy Richards Comfigrip Advanced 40741 Bedienungsanleitung

Morphy Richards

Morphy Richards Steam Generator Handbuch

Morphy Richards

Morphy Richards easyCHARGE 303250 Bedienungsanleitung

Morphy Richards

Morphy Richards Comfigrip 40704 Bedienungsanleitung

Morphy Richards

Morphy Richards Semi-electronic iron Bedienungsanleitung

Morphy Richards

Morphy Richards 40692 Bedienungsanleitung

Morphy Richards

Morphy Richards IB40310 Bedienungsanleitung

Morphy Richards

Morphy Richards Precise Steam Iron Bedienungsanleitung

Morphy Richards

Morphy Richards ELITE 42288 Bedienungsanleitung

Morphy Richards

Morphy Richards Saturn IntelliTemp 305003 Bedienungsanleitung

Morphy Richards

Morphy Richards 303100 Bedienungsanleitung

Morphy Richards

Morphy Richards COMFIGRIP Bedienungsanleitung

Morphy Richards

Morphy Richards Precise Steam Plus Bedienungsanleitung

Morphy Richards

Morphy Richards Jet Stream Elite S Bedienungsanleitung

Morphy Richards

Morphy Richards Power SteamElite RN42221MUK Bedienungsanleitung

Morphy Richards

Morphy Richards INTELLIDOME Bedienungsanleitung

Morphy Richards

Morphy Richards 40850 COMFIGRIP IRON Bedienungsanleitung

Morphy Richards

Morphy Richards Power SteamPro Bedienungsanleitung

Beliebte Eisen Handbücher anderer Marken

Clatronic

Clatronic DB 3703 Bedienungsanleitung

TEFAL

TEFAL FV4093Z0 Bedienungsanleitung

Gorenje

Gorenje SIH 2200 BS Bedienungsanleitung

Philips

Philips GC6012 Bedienungsanleitung

Bosch

Bosch 2 Series Bedienungsanleitung

Riffel

Riffel Catena KB-819 Bedienungsanleitung

Texi

Texi Hestia Bedienungsanleitung

Maxwell

Maxwell MW-3010 Bedienungsanleitung

TREVIDEA

TREVIDEA Girmi ST60 Bedienungsanleitung

Philips

Philips HI5914/30 Bedienungsanleitung

Primula

Primula Vapormat Bedienungsanleitung

Magio

Magio MG-541 Bedienungsanleitung

Scarlett

Scarlett SC-1334S Bedienungsanleitung

Bosch

Bosch Sensixx B22L Bedienungsanleitung

Philips

Philips GC651 Bedienungsanleitung

Vitek

Vitek VT-1247 VT Bedienungsanleitung

Cleanmaxx

Cleanmaxx 3397 Bedienungsanleitung

Philips

Philips GC800 Bedienungsanleitung