Morrison Bros. co. 1218C Handbuch

Morrison Bros. Co. ‑ Dubuque, IA ‑ 800‑553‑4840

1218C‑0197 PP

rev. 03-08-18

The 1218C External Input/Output Expansion Module is an accessory to the 1218C Electronic Tank Gauge. This

module provides an additional 6 digital inputs, and 6 relay outputs when connected to a 1218C Electronic Tank

Gauge

Failure to follow any or all of the warnings and instructions in this document could result in a hazardous

liquid spill, which could result in property damage, environmental contamination, re, explosion, serious

injury or death.

Le fait de ne pas se conformer à l’un ou l’autre des avertissements ou à l’une ou l’autre des directives

apparaissant dans ce document pourrait donner lieu à des déversements de liquides dangereux, lesquels

pourraient engendrer des dommages matériels, des risques de contamination environnementale,

d’incendie ou d’explosion, des blessures graves ou la mort.



Input Power Digital Inputs (6)

100 – 240 VAC, 50/60Hz Dry Contact (DI to GND) – ON: Closed / OFF: Open

Operating Temperature Relay Outputs (6)

-40°F to 140°F (-40°C to 60°C) 2 Amp maximum at up to 250 VAC or 30 VDC

Enclosure Rating Maximum Wiring Distance

NEMA 4X Ethernet – 330ft (CAT5e cable recommended)

Inputs – 500ft (22 AWG wire recommended)

Outputs – 500ft (18 AWG wire recommended



Warnings

• Fire Hazard – Death or serious injury could result from spilled liquids.

• You must be trained to install or maintain this Electronic Tank Gauge. Stop now if you have not been trained.

• Anymodicationofthisunitbeyondwhatisoutlinedinthisinstructionwillvoidproductwarranty.

• For your safety, it is important to follow local, state, federal and/or OSHA rules that apply to working

inside, above, or around the storage tank and piping area. Use all personal protective equipment required for

workinginthespecicenvironment.

• Tankscouldbeunderpressure.Vaporscouldbeexpelledfromtankvents,piping,valvesorttingswhile

performingmaintenance.Vaporscouldcatchreorcauseanexplosion.Avoidsparks,opename,orhot

tools when working on tank system.

• Use a dampened cloth when cleaning the alarm enclosure to prevent static buildup and discharge.

• In the event of malfunction, contact Morrison Bros. Co. Customer Service.





Morrison Bros. Co. ‑ Dubuque, IA ‑ 800‑553‑4840

1218C‑0197 PP

rev. 03-08-18

!

• Risque d’incendie – Un déversement de liquide pourrait entraîner des blessures graves ou la mort.

• Vous devez avoir reçu une formation pour installer cette jauge de réservoir électronique ou en assurer la

maintenance. Arrêtez-vous immédiatement si vous n’avez reçu aucune formation à cet effet.

• Touteslesmodicationsapportéesàcetteunitéautresquecellesindiquéesdanscesdirectivesengendreront

l’annulation de la garantie du produit.

• Pour assurer votre sécurité, il est important de vous conformer à la réglementation locale, d’État, fédérale

ou OSHA régissant les travaux à l’intérieur, au-dessus ou autour du réservoir de stockage et de la zone de

canalisation. Utilisez tout l’équipement de protection individuelle exigé pour travailler dans l’environnement

spécique.

• Les réservoirs pourraient être sous pression. Des vapeurs pourraient être expulsées des conduits d’aération,

des canalisations, des soupapes ou des raccords du réservoir durant la maintenance. Les vapeurs pourraient

s’enammerouengendreruneexplosion.Évitezlesétincelles,lesammesnuesoulesoutilschaudslorsde

travaux menés dans le système du réservoir.

• Utilisezunlingehumidepournettoyerl’enceintedel’alarmeandeprévenirl’accumulationd’électricité

statique et les décharges.

• En cas de défaillance, communiquez avec le service à la clientèle de Morrison Bros. Co.

WARNING: ThisdeviceisintendedtobeinstalledinanOrdinaryLocation(UnclassiedLocation)andbeused

with other Ordinary Location devices.

Mounting

To maintain the NEMA 4X rating

•ThreeopeningshavebeenprovidedinthebottomoftheNEMA4Xenclosureforconnectionandwiring.

Only use Thomas & Betts Cat. No. H050GR-TB or H050-TB or equivalent hubs in the one opening

for ½” conduit and Thomas & Betts Cat. No. H075GR-TB or H075-TB or equivalent hubs in the two

openings for ¾” conduit.

•Mountingtabshavebeenprovidedwiththeproducttomounttheenclosure;donotmakeadditionalholes

in this enclosure.

•Ensurethatbothcoverlatchesarelatchedatalltimes.

Failure to follow these instructions voids any assurance that the enclosure is NEMA 4X.

Wiring

The 1218C External Input/Output Expansion Module (I/O Module) communicates with the 1218C Electronic

Tank Gauge (1218C) over an Ethernet connection. The I/O Module contains a 2-port Ethernet switch that

can be used to daisy chain the Ethernet connection to a network allowing both devices to be accessible from

the network. This is especially useful for new installations to reduce the amount of Ethernet cabling and/or

networking devices required to connect the I/O Module and 1218C to a computer or network.

Figure 1 shows the digital input and relay output connections of the Moxa E1214-T device contained within

theI/OModule.Uptosixdryorwetcontactdevices(seespecicationssection)canbeconnectedtothedigital

input channels (DI). The dry contact inputs must share a common ground connection (GND), and the wet contact

inputs must share a common source/return (COM). The proper connections for dry contact and wet contact

devices are illustrated in Figure 2 and Figures 3 and 4, respectively.

Figure 1— I/O Module Input and Relay Connections

Morrison Bros. Co. ‑ Dubuque, IA ‑ 800‑553‑4840

1218C‑0197 PP

rev. 03-08-18

UptosixrelayoutputscanbeconnectedtoACorDCloads(seespecicationssection).TheI/OModuledoes

not provide power to the loads. The loads being driven must supply their own power. Figure 5 shows the proper

connection of a relay output to a power source and load.

Figure 2— Digital Input connection to Dry Contact Output

Figure 3—Digital Input wiring to Sinking Wet Contact Output (NPN)

Figure 4—Digital Input wiring to Sourcing Wet Contact Output (PNP)

Figure 5—Relay Output Connection

The input power should be wired to the power supply connections labelled ‘L’, ‘N’, and Ground (symbol) in the

I/O Module as shown in Figure 6. A grounding stud is provided to tie all ground connections together.

Figure 6—AC Input Connections

Morrison Bros. Co. ‑ Dubuque, IA ‑ 800‑553‑4840

1218C‑0197 PP

rev. 03-08-18

IMPORTANT: To prevent premature failure of the relay contacts it is strongly recommended to use a fuse and

transient voltage suppressor (e.g. varistor, TVS diode). See Figure 5 for details.

Preparation

BeforestartingthecongurationprocessndthestaticIPaddressofthe1218CElectronicTankGaugeand

recordthisaddressbelowasitwillbeusedduringthecongurationprocess.Ifthe1218CConsoleisusing

DHCPyouwillneedtocongureitwithastaticIPaddressbeforecontinuing.Referto‘ConguringYour

1218C’ofthe‘StepstoCongurethe1218C’sectioninthe‘1218CElectronicTankGaugeIOM’fordetailson

conguringastaticIPaddress.

Next you will need to obtain a static IP address for the I/O Module. Record this IP address below for reference

throughoutthecongurationprocess.

IMPORTANT: The 1218C External I/O Module and 1218C Electronic Tank Gauge must be allocated static IP

addressesbythenetworkadministratorandmustnotconictwithanyotherdevicesonthenetwork.

Static IP Address Assignments:

1218C External I/O Module __ __ __ . __ __ __ . __ __ __ . __ __ __

1218C Electronic Tank Gauge __ __ __ . __ __ __ . __ __ __ . __ __ __

Finally,youwillneedtodownloadandinstalltheMoxaioSearchCongurationUtilitytoyourPC.The

software can be downloaded by going to the product webpage.

https://www.moxa.com/product/ioLogik_E1214.htm

Nextselect‘Drivers&Software’.TheioSearchCongurationUtilitycanbefoundunder‘Software→Utilities’.

Initial Conguration

TheI/OModulemustbeconguredusingtheMoxaioSearchCongurationUtilitybeforeitcancommunicate

with the 1218C Electronic Tank Gauge.

1. Ensure power is applied to the I/O Module

2. Run the Moxa IoSearch Utility from a computer “direct connected” or “network connected” to the I/O

Module.

3. Select only ‘Ethernet Remote I/O’ and click ‘Start Search’

Morrison Bros. Co. ‑ Dubuque, IA ‑ 800‑553‑4840

1218C‑0197 PP

rev. 03-08-18

4.Startbyconguringthe‘NetworkSettings’…

a. Click on the ‘E1214-T’ device in the navigation pane on the left side of the screen to open the

congurationpage.IfnodeviceswerefoundverifytheE1214-Tlightsfor‘Power’,‘Ready’,

and‘Port’areilluminated/ashing.Seethe“ioLogikE1200SeriesUser’sManual”forhelp

troubleshooting.

b. Under ‘General Settings’ set the ‘Server Name’ and ‘Server Location’ and click ‘Submit’ to save

thechanges.Theseeldswillhelpidentifythisdevicefromotherdevicesonthenetwork.

c.Under‘EthernetConguration’setthestatic‘IPAddress’,‘SubnetMask’,and‘Gateway’then

click ‘Submit’ to save the changes.

NOTE: Submittingcongurationchangestothedevicerequiresarestart.However,thisrestartcanbe

postponeduntilallcongurationchangeshavebeenmade.

5.Nextcongurethe‘SNMPSettings’…

a. Under ‘SNMP Agent’ ensure ‘SNMP’ is set to ‘Enable’ and click ‘Submit’ to save the change (if

necessary).

b. Under ‘SNMP Trap Settings’ enter the 1218C Electronic Tank Gauge IP Address (recorded above)

inthersttextbox.

c.Clickthecheckboxnextto‘SNMPTrap’toselectalltrapsandclick‘Submit;tosavethechanges.

6. Next, click ‘Change Password’ and enter a new password for the device. Leave the ‘Old Password’ blank and

click ‘Submit’.

7. Finally, click the ‘Save/Restart’ to reboot the device for the changes to take effect.

8. Wait for the device to reboot and verify all settings are correct.

Failure to follow any or all of the warnings and instructions in this document could result in a hazardous

liquid spill, which could result in property damage, environmental contamination, re, explosion, serious

injury or death.

Morrison Bros. Co. ‑ Dubuque, IA ‑ 800‑553‑4840

1218C‑0197 PP

rev. 03-08-18

Le fait de ne pas se conformer à l’un ou l’autre des avertissements ou à l’une ou l’autre des directives

apparaissant dans ce document pourrait donner lieu à des déversements de liquides dangereux, lesquels

pourraient engendrer des dommages matériels, des risques de contamination environnementale,

d’incendie ou d’explosion, des blessures graves ou la mort.



Warnings

• Fire Hazard – Death or serious injury could result from spilled liquids.

• You must be trained to install or maintain this Electronic Tank Gauge. Stop now if you have not been trained.

• Anymodicationofthisunitbeyondwhatisoutlinedinthisinstructionwillvoidproductwarranty.

• For your safety, it is important to follow local, state, federal and/or OSHA rules that apply to working

inside, above, or around the storage tank and piping area. Use all personal protective equipment required for

workinginthespecicenvironment.

• Tankscouldbeunderpressure.Vaporscouldbeexpelledfromtankvents,piping,valvesorttingswhile

performingmaintenance.Vaporscouldcatchreorcauseanexplosion.Avoidsparks,opename,orhot

tools when working on tank system.

• Use a dampened cloth when cleaning the alarm enclosure to prevent static buildup and discharge.

• In the event of malfunction, contact Morrison Bros. Co. Customer Service.



• Risque d’incendie – Un déversement de liquide pourrait entraîner des blessures graves ou la mort.

• Vous devez avoir reçu une formation pour installer cette jauge de réservoir électronique ou en assurer la

maintenance. Arrêtez-vous immédiatement si vous n’avez reçu aucune formation à cet effet.

• Touteslesmodicationsapportéesàcetteunitéautresquecellesindiquéesdanscesdirectivesengendreront

l’annulation de la garantie du produit.

• Pour assurer votre sécurité, il est important de vous conformer à la réglementation locale, d’État, fédérale

ou OSHA régissant les travaux à l’intérieur, au-dessus ou autour du réservoir de stockage et de la zone de

canalisation. Utilisez tout l’équipement de protection individuelle exigé pour travailler dans l’environnement

spécique.

• Les réservoirs pourraient être sous pression. Des vapeurs pourraient être expulsées des conduits d’aération,

des canalisations, des soupapes ou des raccords du réservoir durant la maintenance. Les vapeurs pourraient

s’enammerouengendreruneexplosion.Évitezlesétincelles,lesammesnuesoulesoutilschaudslorsde

travaux menés dans le système du réservoir.

• Utilisezunlingehumidepournettoyerl’enceintedel’alarmeandeprévenirl’accumulationd’électricité

statique et les décharges.

• En cas de défaillance, communiquez avec le service à la clientèle de Morrison Bros. Co.

Theoperationofthe1218CExternalI/OModuleisconguredthroughthewebinterfaceofthe1218C

ElectronicTankGauge.EachoftheI/OModule’sdigitalinputscanbeconguredtogeneratealarmconditions

thatcansoundthebuzzer,activaterelayoutputs,sendemailortextnotications,and/orcreateeventlogentries.

InadditiontheI/OModule’srelayoutputscanbeconguredtoactivateonanycombinationofalarmconditions

within the 1218C Electronic Tank Gauge.

BeforeconguringtheoperationoftheI/OModule,ensurethe1218CElectronicTankGaugermwareis

up-to-date. Refer to ‘Firmware Upgrades’ of the ‘Maintenance’ section in the ‘1218C Electronic Tank Gauge

IOM’fordetailsonupdatingthe1218Crmware.Thelatestrmwareanddocumentationcanbefoundunder

‘Downloads’ on the 1218C product webpage.

http://morbros.com/1218

Morrison Bros. Co. ‑ Dubuque, IA ‑ 800‑553‑4840

1218C‑0197 PP

rev. 03-08-18

Conguration

Oncethe1218Crmwareisup-to-date,openawebbrowserandgotothe1218Ccongurationwebpageto

beginconguringtheoperationoftheI/OModule.

1. Expand the ‘External I/O’ section and set the ‘IP Address’ of the I/O Module (recorded above) and then set

the ‘Status’ to ‘Enabled’.

2.Expandthe‘ExternalInputs’sectionandselectanExternalInputthatistobeenabled…

a. Set the ‘Name’ setting (up to 14 characters)

b. Set the ‘Type’ setting (Normally Open or Normally Closed)

c. Set the ‘Buzzer’ setting (Auto-Silence, On, or Off)

d. Set the ‘Log Alarm Events’ setting (Enabled or Disabled)

e. Set the ‘Status’ setting to ‘Enabled’

3. Repeat the previous step for any other inputs that are to be enabled.

4.Expandthe‘ExternalRelays’sectionandselectanExternalRelaythatistobeenabled…

a. Set the ‘Name’ setting (up to 14 characters)

b. Set the ‘Type’ setting (Normally Activated or Normally Deactivated)

c. Set the ‘Mode’ setting (Persistent, Non-Persistent, or Auto-Timeout)

d. Set the ‘Log Alarm Events’ setting (Enabled or Disabled)

Morrison Bros. Co. ‑ Dubuque, IA ‑ 800‑553‑4840

1218C‑0197 PP

rev. 03-08-18

e. Set the ‘Status’ setting to ‘Enabled’

5. Repeat the previous step for any other relays that are to be enabled.

6.Next,youmustassignalarmsourcestoeachofthepreviouslyconguredExternalRelays.Clickonthebutton

to ‘Select alarm sources to trigger relay output activation’

7. For each I/O Module Output (rows of table) select the desired alarm source(s) and click the ‘Save’ button to

nish.

NOTE: Level alarms are designated L1-L4, input alarms are designated I1-I6, while communication and low

voltage alarms are designated C and V, respectively.

Morrison Bros. Co. ‑ Dubuque, IA ‑ 800‑553‑4840

1218C‑0197 PP

rev. 03-08-18

8.TouseanyofthepreviouslyconguredExternalInputstotriggeraninternal1218Crelayoutput,expandthe

‘Relay Outputs’ section and click on the button to ‘Select alarm sources to trigger relay output activation.’

9.ForeachInternalRelay(rowsoftable)selectthedesiredalarmsource(s)andclickthe‘Save’buttontonish.

Morrison Bros. Co. ‑ Dubuque, IA ‑ 800‑553‑4840

1218C‑0197 PP

rev. 03-08-18

10.ToenableEmailorTextnotications,expandthe‘EmailNotications’section…

a. Set the ‘Type’ setting (Email or Text)

b. Set the ‘Email Address’ (make sure it is correct before proceeding)

c. Set the ‘Input Alarms’ setting to ‘Enabled’

d. Set the ‘Email Status’ setting to ‘Enabled’

Verication

AftercompletingthecongurationoftheI/OModuleyoumustverifythatitisoperatingasintended.Startby

verifying that the I/O Module is enabled and communicating properly with the 1218C. Open the status web page

and verify that the ‘External Inputs’ section does not show “DISABLED” or “COM ERROR”. Instead it should

display “NO ALARMS” or any active alarms if the sensors are connected and in the active state.

Next verify that each input is being detected by the 1218C by activating the input and verifying the External

Inputalarmshowsuponthestatuswebpage,oralternatively,lookfortheashingLEDonthefrontofthe

1218C console. If you have enabled any of the External Relays you must also verify that the relays activate

whentheconguredinputalarmisactive.Referto‘ConguringYour1218C’ofthe‘StepstoCongurethe

1218C’sectioninthe‘1218CElectronicTankGaugeIOM’fordetailsonthecongurationofinputsensor

alarms and output relays.

Andere Handbücher für 1218C

Inhaltsverzeichnis

Andere Morrison Bros. co. E/A-System Handbücher

Morrison Bros. co.

Morrison Bros. co. 918AC Series Handbuch

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung