Morse 410M-124 Bedienungsanleitung

The Specialist In Drum Handling Equipment

Model 410M-124

Heavy-Duty Hydra-Lift, 72”, Air Power Lift, Manual Tilt,

with Spark Resistant Parts

morsedrum.com

CONTENTS

Page

Receiving Procedures. . . . . . . . . . . . . . . . . 1

Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Safety Information. . . . . . . . . . . . . . . . . . . . . 1 - 2

Machine Description. . . . . . . . . . . . . . . . . . . 3 - 4

Operating Instructions. . . . . . . . . . . . . . . . . . . 4 - 5

Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . 5

Safety Information

While Morse Manufacturing Co. drum handling equipment is

engineered for safety and e󰀩ciency, a high degree of responsibility

must be placed upon the machine operator to follow safe practices,

based primarily on common sense, upon which true safety

depends.

Failure to follow the safety precautions in this manual can result in

personal injury or property damage. Observe the same precautions

as with similar machinery where carelessness in operating or

maintenance is hazardous to personnel. Carefully read the safety

precautions below and throughout this manual.

Receiving Procedures

Every Morse drum handler is inspected prior to shipping. However,

damage may be incurred during transit.

• Check for visible damage. If you choose to accept damaged

freight, always sign noting the damage on the BILL OF LADING.

• Document the damage and have the truck driver sign. We

recommend keeping a digital camera at your receiving dock for

this purpose.

• Open packages expeditiously to check the condition of the

goods. There is only a 24 hour window to notify the carrier of any

concealed damage.

• IMMEDIATELY REPORT ALL DAMAGE TO THE SHIPPING

COMPANY! Then you may contact Morse for assistance with

your freight claim.

• Morse Manufacturing will not be held responsible for any

damaged freight that is not signed for as damaged.

Delivery to non-business addresses without a loading dock result

in additional freight charges. Residential delivery fees, inside

delivery fees, re-delivery charges, and lift gate services will be

added by the truck line, and are non-negotiable.

Limited 2 Year Warranty

Morse drum handling equipment is guaranteed against defects in

workmanship or materials for TWO YEARS when used properly

within its rated capacity. Warranty does not cover wear from

normal use or damage from accident or abuse. Motors and

other purchased parts carry the warranties of their manufacturers.

For warranty claims, contact your Morse Dealer to obtain a

return authorization number, and for return freight advice. Return

freight must be prepaid.

In all instances, liability is limited to the purchase price paid or to

repairing or replacing the product. Customer assumes liability for

any modications, unauthorized repairs or parts substitution.

Operator’s Manual

for Morse

Heavy-Duty Hydra-Lift Drum Karrier

with Spark Resistant Parts

Model 410M-124

Serial Number 1210 to ____ (MMYY)

The Specialist In Drum Handling Equipment

Model 410M-124

Heavy-Duty Hydra-Lift, 72”, Air Power Lift, Manual Tilt,

with Spark Resistant Parts

Operator’s Manual for Morse Heavy-Duty Hydra-Lift Karrier with Spark Resistant Parts - Model 410M-124

Serial Number 1210 to ____ (MMYY)

morsedrum.com

Safety Information (continued)

DANGER - Indicates a situation which, if not avoided, will result in serious injury or

death. This signal word is limited to the most extreme situations.

WARNING - Indicates a situation which, if not avoided, could result in serious

injury or death.

CAUTION - Indicates a situation which, if not avoided, can result in damage to the

machine.

CAUTION – Do Not Transport with Drum Raised

ALWAYS LOWER THE DRUM HOLDER TO LOWEST POSITION BEFORE TRANSPORTING. The

unit can become unstable when transporting with a raised load.

DANGER - Stay Clear of Power Lines

KEEP WELL CLEAR OF POWER LINES. Never approach a power line. Current in a high voltage line

may arc some distance from the wire to the steel framed, grounded machine.

WARNING

The Heavy-Duty Hydra-Lift Karrier is designed to handle one drum of the types listed at the top of page

3, under 2. Machine Description. DO NOT attempt to handle any other type of drum or object. DO

NOT exceed the weight capacity.

WARNING - Level Floors Only

For operation only on clean, level oors of suitable bearing capacity. Do not use on sloped surfaces,

ramps, irregular or debris strewn oors.

WARNING - Do Not Modify the Unit

Under no circumstances should any modications be made to the Morse machinery without factory

authorization. Any modications may void the warranty. This machine was designed to perform a

specic job and alterations may result in injury to operator or machine.

WARNING - No Loose Fitting Clothing

Wear close-tting clothing and safety equipment appropriate to the job. Loose tting clothing may

become caught on the machinery and cause severe personal injury.

WARNING - Hydraulic Fluid Under Pressure Can Be Hazardous

Escaping hydraulic uid under pressure can penetrate the skin, causing serious injury. Avoid the

hazard by relieving pressure before disconnecting hydraulic lines. Keep hands and body away from

pinholes and nozzles, which eject uid under high pressure. Use a piece of cardboard to search for

leaks. If an accident occurs, see a doctor immediately and inform them of the nature of the accident.

CAUTION - Wear Safety Shoes - Wear safety shoes with non-slip soles and hard toe protection.

WARNING: This product can expose you to chemicals including barium sulfate, cobalt, titanium

dioxide, and 2-methylimidazole, which are known to the State of California to cause cancer, and

bisphenol-A, which is known to the State of California to cause birth defects or other reproductive harm.

For more information go to www.P65Warnings.ca.gov

The Specialist In Drum Handling Equipment

Model 410M-124

Heavy-Duty Hydra-Lift, 72”, Air Power Lift, Manual Tilt,

with Spark Resistant Parts

Operator’s Manual for Morse Heavy-Duty Hydra-Lift Karrier with Spark Resistant Parts - Model 410M-124

Serial Number 1210 to ____ (MMYY)

morsedrum.com

Machine Description

The Model 410M-124 Heavy-Duty Hydra-Lift Karrier will pour a drum up

to 72” (183 cm) high, measured from the oor to the lowest point of a

horizontal drum. It is designed to lift, transport, and dispense a 55-gallon

(210 liter) steel or ber drum 22” to 23.5” (56 to 59.7 cm) in diameter.

The maximum full-drum capacity is 1200 Lb. (544 kg). The capacity

is derated to 600 Lb. (272 kg) for a half-full drum. The half-full rating

is based on the tilt mechanism’s capacity for handling an unbalanced

bottom-heavy drum.

Options

A smaller diameter drum can be handled with the correct size 55/30M •

Series Diameter Adapter installed (see Diameter Adapter literature).

The adjustable Bracket Assembly (Kit # 4556M-P) is • required to

handle a plastic drum without a top rim (see gure 2.1). The Bracket

Assembly is also recommended when handling a ber drum. You

can also use the Bracket Assembly when handling a rimmed drum. It

adjusts for a drum 31” to 39” (79 to 99 cm) tall.

To handle a 55-gallon (210 liter) plastic drum with suitable top rim, •

you must install either the Bracket Assembly or the Top Rim Clamp

(Kit # 4560M-P) (see gure 2.2). You can use the Top Rim Clamp to

handle a 55-gallon (210 liter) plastic, steel or ber drum with suitable

top rim.

Controls

The Morse Heavy-Duty Hydra-Lift Karrier is manually propelled and steered. The drum

lift is powered by an air motor with an on/o󰀨 valve. There are two functions for the

operator to control (Figure 2.3):

1. LIFT and Lower Function to raise and lower the drum

Plug your air line into the on/o󰀨 air valve.•

Turn the motor on by holding the valve handle in the on position. The drum will •

lift.

Release the valve handle when the drum is at the desired height.•

To lower the drum: With the motor o󰀨, push in the LOWER handle.•

2. TILT Function to control the degree of rotation of the drum.

Pull down on one side of chain, rotating drum to angle required for pouring.•

The drum handler is equipped with the MORStop Tilt-Brake, there is no need •

to hold tension on both sides of the chain loop. Braking is immediate and self-

actuating, without additional steps by the operator.

Figure 2.3

Figure 2.2

Plastic drum being lifted

with Kit # 4560M-P Top

Rim Clamp Assembly

installed.

Figure 2.1

Plastic drum being lifted

with Kit # 4556M-P Bracket

Assembly installed.

The Specialist In Drum Handling Equipment

Model 410M-124

Heavy-Duty Hydra-Lift, 72”, Air Power Lift, Manual Tilt,

with Spark Resistant Parts

Operator’s Manual for Morse Heavy-Duty Hydra-Lift Karrier with Spark Resistant Parts - Model 410M-124

Serial Number 1210 to ____ (MMYY)

morsedrum.com

WARNING - Watch Out for Pinch Points

Stay clear of moving parts. Operator should remain behind the push handle during the lift operation.

Figure 3.2

Floor Lock

The step-down oor lock is located behind the base (gure 3.1).

To activate, step down on the oor lock until it locks in the down

position. When the oor lock is activated it prevents unwanted free

wheeling of the unit. Floor conditions determine the e󰀨ectiveness

of the oor lock. The operator should verify its holding action

before depending on it to hold.

MORCINCHTM Drum Holder Assembly

The drum holder assembly (or “saddle assembly”) is the

component on the Heavy-Duty Hydra-Lift Karrier that is intended

to hold the drum. The MORCINCHTM drum holder assembly is

designed to secure a standard ribbed 55-gallon (210 liter) steel

drum around it’s middle using a cinch chain and ratchet tightening

system. The MORCINCHTM drum holder accepts accessories for

handling a plastic drum, a ber drum, or smaller diameter drums

(see Options on pg. 3).

Operating Instructions

1.) Push the Heavy-Duty Hydra-Lift Karrier to the drum.

2.) Using the “LIFT” control as described in “Machine Description

- Controls” (page 3), position the drum holder assembly with

the back band at the middle of the drum. (Figure 3.1). With

the ratchet plate swung open and the cinch chain hanging

from the chain hook, push the unit until the back band rests

rmly against the drum. Some adjustment to the tilt angle of

the saddle may be necessary to ensure band ts ush on the

drum.

3.) Attaching the drum:

Drape the chain across the front of the drum and engage a

link into the slot in the ratchet (Figure 3.2). Turn the ratchet

clockwise to tighten chain. If ratchet turns until the pawl is

beyond the last ratchet tooth, turn the ratchet back and slide the

next link into the ratchet slot and try tightening again. The chain

must be held tightly against the drum with the pawl engaged

securely in the ratchet teeth.

4.) Operate the lift function to lift drum clear of oor. Roll to

dispensing location. NOTE: Do not allow the drum to impact on

oor, pouring station, etc. or a spill or damage could occur.

Figure 3.1

The Specialist In Drum Handling Equipment

Model 410M-124

Heavy-Duty Hydra-Lift, 72”, Air Power Lift, Manual Tilt,

with Spark Resistant Parts

Operator’s Manual for Morse Heavy-Duty Hydra-Lift Karrier with Spark Resistant Parts - Model 410M-124

Serial Number 1210 to ____ (MMYY)

morsedrum.com

CAUTION – Do Not Transport with Drum Raised

ALWAYS LOWER THE DRUM HOLDER TO LOWEST POSITION BEFORE TRANSPORTING. The

unit can become unstable when transporting with a raised load.

5.) Lift drum to desired pouring height. Operate the tilt control as described in “Machine Description - Controls” (page 3)

to adjust the drum attitude. This is especially important when lifting an open drum. The oor lock should be engaged while

dispensing / draining.

6.) When dispensing is complete, tilt drum back to upright position. Disengage the oor lock and lower the drum to transport-

ing height; about 6” (15 cm) o󰀨 the oor.

WARNING - Stay Clear of Raised Drum

NEVER allow anyone to be below any part of a raised drum handler or drum. Remain behind the

push handle while handling a drum.

WARNING – Do NOT Disengage the Cinch Chain When Drum is o󰀨 the Ground

When the drum is in the upright position, lower the drum to the oor before releasing the cinch

chain.

7.) Push the unit to the drum storage area and lower to the oor in an upright position. Release the cinch chain from the

ratchet by applying pressure to the ratchet handle in a clockwise direction with one hand and opening the pawl to free

the ratchet with the other hand. Remove the cinch chain link from the ratchet.

Maintenance

Periodic inspection for the general condition of structural and mechanical components is imperative for safe and e󰀩cient

operation.

Periodically inspect all moving parts, framework, and contact areas for signs of wear, fatigue, or loosening. Tighten, adjust,

or replace parts as necessary to prevent failure and maintain proper function.

Inspect the hydraulic system for oil drips, hose damage, or other signs of wear. Inspect the level and condition of the hydraulic

uid. Replace any parts that show signs of wear.

Grease wheel bearings periodically. Oil or grease all moving parts including: the clevis pins and the surfaces of the boom which

contact the inside of the mast cap, the gears and sprockets in the tilt drive, and the ratchet and pawl.

Worn or damaged parts must be properly replaced with the correct, genuine Morse parts.

Hydraulic pump is shipped lled with Noco Premium plus automatic transmission uid d/m. Material safety data sheet

(MSDS) is available online. Change oil yearly, sooner depending on dirty conditions or outdoor use. Replace oil with Mobil

dte 24 or equivalent for indoor use (Mobil dte 13 for outdoor use).

Inhaltsverzeichnis

Andere morse Hebesystem Handbücher

morse

morse Hydra-Lift 400A-96 Bedienungsanleitung

morse

morse 520 Bedienungsanleitung

morse

morse MORStak 289F Bedienungsanleitung

morse

morse 152 Bedienungsanleitung

morse

morse 40 Bedienungsanleitung

morse

morse 515-N-110 Bedienungsanleitung

morse

morse 400AM-60 Bedienungsanleitung

morse

morse 400A-72SS Bedienungsanleitung

morse

morse 195A Series Bedienungsanleitung

morse

morse 400AM-72-124 Bedienungsanleitung

morse

morse 400A-60-117 Bedienungsanleitung

morse

morse 525-N-115 Bedienungsanleitung

morse

morse 525SS-N-115 Bedienungsanleitung

morse

morse 81 Bedienungsanleitung

morse

morse 510-125 Bedienungsanleitung

morse

morse 400A-60-127 Bedienungsanleitung

morse

morse 42 Series Bedienungsanleitung

morse

morse 400A-60-125 Bedienungsanleitung

morse

morse 510SS-110 Bedienungsanleitung

morse

morse 520M-124 Bedienungsanleitung

morse

morse 525-N-114 Bedienungsanleitung

morse

morse 400A-60-110 Bedienungsanleitung

morse

morse 400A-96SS-117 Bedienungsanleitung

morse

morse 515M-T-124 Bedienungsanleitung

Beliebte Hebesystem Handbücher anderer Marken

Braun

Braun NL955 Series Bedienungsanleitung

haacon

haacon 1889.10 Bedienungsanleitung

Protekt

Protekt AT 252 Bedienungsanleitung

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Bedienungsanleitung

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Bedienungsanleitung

Genie

Genie Z-60/34 Bedienungsanleitung

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Bedienungsanleitung

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Bedienungsanleitung

Custom Equipment

Custom Equipment Hy-Brid 3 Series Programmierhandbuch

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Programmierhandbuch

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Programmierhandbuch

BERG

BERG BeNomic EasyLeaf Bedienungsanleitung

Powermate

Powermate LiftGate LG-3 Bedienungsanleitung

Snorkel

Snorkel TM12 Series Bedienungsanleitung

Terberg

Terberg OMNIDEKA Bedienungsanleitung

Harmar Mobility

Harmar Mobility AL625 Betriebsanleitung

Rotary

Rotary SPO16 Bedienungsanleitung

Ricon

Ricon Mirage F9T Bedienungsanleitung

morse 410M-124 Bedienungsanleitung

Beliebte Hebesystem Handbücher anderer Marken