Morse 400A-72SS-120 Bedienungsanleitung

The Specialist In Drum Handling Equipment

Model 400A-72SS-120

Stainless Steel Hydra-Lift,

72”, AC Power Lift, Manual Tilt

morsedrum.com

Operator’s Manual

for Morse

Stainless Steel Hydra-Lift Drum Karrier

Model 400A-72SS-120

Serial Number 0914 to ____ (MMYY)

Safety Information

While Morse Manufacturing Co. drum handling equipment is

engineered for safety and e󰀩ciency, a high degree of responsibility

must be placed upon the machine operator to follow safe practices,

based primarily on common sense, upon which true safety

depends.

Failure to follow the safety precautions in this manual can result in

personal injury or property damage. Observe the same precautions

as with similar machinery where carelessness in operating or

maintenance is hazardous to personnel. Carefully read the safety

precautions below and throughout this manual.

Receiving Procedures

Every Morse drum handler is inspected prior to shipping. However,

damage may be incurred during transit.

• Check for visible damage. If you choose to accept damaged

freight, always sign noting the damage on the BILL OF LADING.

• Document the damage and have the truck driver sign. We

recommend keeping a digital camera at your receiving dock for

this purpose.

• Open packages expeditiously to check the condition of the

goods. There is only a 24 hour window to notify the carrier of any

concealed damage.

• IMMEDIATELY REPORT ALL DAMAGE TO THE SHIPPING

COMPANY! Then you may contact Morse for assistance with

your freight claim.

• Morse Manufacturing will not be held responsible for any

damaged freight that is not signed for as damaged.

Delivery to non-business addresses without a loading dock result

in additional freight charges. Residential delivery fees, inside

delivery fees, re-delivery charges, and lift gate services will be

added by the truck line, and are non-negotiable.

Limited 2 Year Warranty

Morse drum handling equipment is guaranteed against defects in

workmanship or materials for TWO YEARS when used properly

within its rated capacity. Warranty does not cover wear from

normal use or damage from accident or abuse. Motors and

other purchased parts carry the warranties of their manufacturers.

For warranty claims, contact your Morse Dealer to obtain a

return authorization number, and for return freight advice. Return

freight must be prepaid.

In all instances, liability is limited to the purchase price paid or to

repairing or replacing the product. Customer assumes liability for

any modications, unauthorized repairs or parts substitution.

CONTENTS

Page

Receiving Procedures. . . . . . . . . . . . . . . . . 1

Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Safety Information. . . . . . . . . . . . . . . . . . . . . 1 - 2

Machine Description. . . . . . . . . . . . . . . . . . . 3 - 4

Accessories. . . . . . . . . . . . . . . . . . . . 3

Start-Up Procedure. . . . . . . . . . . . . . . . 5

Operating Instructions. . . . . . . . . . . . . . . 5

Maintenance. . . . . . . . . . . . . . . . . . . . . . . 6

The Specialist In Drum Handling Equipment

Model 400A-72SS-120

Stainless Steel Hydra-Lift,

72”, AC Power Lift, Manual Tilt

Operator’s Manual for Morse Stainless Steel Hydra-Lift Karrier Model 400A-72SS-120

Serial Number 0914 to ____ (MMYY)

morsedrum.com

Safety Information (continued)

DANGER - Indicates a situation which, if not avoided, will result

in serious injury or death. This signal word is limited to the most

extreme situations.

WARNING - Indicates a situation which, if not avoided, could result

in serious injury or death.

CAUTION - Indicates a situation which, if not avoided, can result in

damage to the machine.

CAUTION – Do Not Transport with Drum Raised

ALWAYS LOWER THE DRUM HOLDER TO LOWEST POSITION BEFORE TRANSPORTING. The

unit can become unstable when transporting with a raised load.

DANGER - Stay Clear of Power Lines

KEEP WELL CLEAR OF POWER LINES. Never approach a power line. Current in a high voltage line

may arc some distance from the wire to the steel framed, grounded machine.

WARNING

The Hydra-Lift Karrier is designed to handle one drum of the types listed at the top of page 3, under

Machine Description. DO NOT attempt to handle any other type of drum or object. DO NOT exceed

the weight capacity of 800 Lb. (363 kg).

WARNING - Level Floors Only

For operation only on clean, level oors of suitable bearing capacity. Do not use on sloped surfaces,

ramps, irregular or debris strewn oors.

WARNING - Do Not Modify the Unit

Under no circumstances should any modications be made to the Morse machinery without factory

authorization. Any modications may void the warranty. This machine was designed to perform a

specic job and alterations may result in injury to operator or machine.

WARNING - No Loose Fitting Clothing

Wear close-tting clothing and safety equipment appropriate to the job. Loose tting clothing may

become caught on the machinery and cause severe personal injury.

WARNING - Hydraulic Fluid Under Pressure Can Be Hazardous

Escaping hydraulic uid under pressure can penetrate the skin, causing serious injury. Avoid the

hazard by relieving pressure before disconnecting hydraulic lines. Keep hands and body away from

pinholes and nozzles, which eject uid under high pressure. Use a piece of cardboard to search for

leaks. If an accident occurs, see a doctor immediately and inform them of the nature of the accident.

CAUTION - Wear Safety Shoes - Wear safety shoes with non-slip soles and hard toe protection.

WARNING: This product can expose you to chemicals including barium sulfate, cobalt, titanium

dioxide, and 2-methylimidazole, which are known to the State of California to cause cancer, and

bisphenol-A, which is known to the State of California to cause birth defects or other reproductive harm.

For more information go to www.P65Warnings.ca.gov

The Specialist In Drum Handling Equipment

Model 400A-72SS-120

Stainless Steel Hydra-Lift,

72”, AC Power Lift, Manual Tilt

Operator’s Manual for Morse Stainless Steel Hydra-Lift Karrier Model 400A-72SS-120

Serial Number 0914 to ____ (MMYY)

morsedrum.com

Machine Description

The Model 400A-72SS-120 Hydra-Lift Karrier will pour a drum up to 72”

(183 cm) high, measured from the oor to the lowest point of a horizontal

drum. It is designed to lift, transport, and dispense a 55-gallon (210 liter)

steel drum 22” to 23.5” (56 to 59.7 cm) in diameter.

The maximum full-drum capacity is 800 Lb. (363 kg). The capacity is

derated to 500 Lb. (227 kg) for a half-full drum. The half-full rating is based

on the tilt mechanism’s capacity for handling an unbalanced bottom-heavy

drum.

Stainless Steel

Hand Wheel

Kit # 2690SS-P

16” (40.6 cm) diameter

Hand Wheel

with speed knob.

Replaces standard

Pull Chain to turn drum.

Kit for customer to install

on EXISTING manual tilt

drum handler.

MORStopTM Tilt-Brake

with Stainless Casing

Kit # 3900SS-P

Automatically holds

drum tilt angle until you

move it.

Kit for customer to install

on EXISTING manual tilt

drum handler.

55/30SS Series Stainless Steel Diameter Adapters for drum with diameter

smaller than 22” (56 cm). To handle a smaller drum, insert the correct size

Diameter Adapter into the standard drum holder. See Diameter Adapter info at:

https://morsedrum.com/products/diameter-adapters

ONLY Diameter Adapters for drum with 17.5” (44.5 cm) diameter or smaller

have integrated brackets to prevent drum slipping length-ways.

NOTE: For 30-gallon (114 Liter) PLASTIC drum, insert Diameter Adapter;

AND install Bracket or Top Rim Clamp to prevent drum slipping.

IMPORTANT: To prevent 30 to 55 gallon (114 to 210 L) size plastic drum from

slipping, you MUST install either Top Rim Clamp Kit or Bracket Assembly Kit.

1. Stainless Steel Bracket Assembly Kit # 4556SS-P

is required to handle a RIMLESS plastic drum (gure 2.1),

and is also recommended for a ber drum. The Bracket

adjusts for a 31” to 39” (79 to 99 cm) tall drum.

You can also handle a rimmed drum with the Bracket installed.

2. Stainless Steel Top Rim Clamp Kit # 4560BSS-P to handle a

RIMMED plastic drum (gure 2.2). Install the Top Rim Clamp Kit to

handle a RIMMED plastic, steel or ber drum with suitable top rim.

ACCESSORIES

Figure 2.2

Stainless Steel

Kit # 4560BSS-P

Install Top Rim Clamp Kit

to handle RIMMED plastic

drum

Figure 2.1

Stainless Steel

Kit # 4556SS-P

Install Bracket Assembly Kit

to handle RIMLESS or

RIMMED plastic drum

The Specialist In Drum Handling Equipment

Model 400A-72SS-120

Stainless Steel Hydra-Lift,

72”, AC Power Lift, Manual Tilt

Operator’s Manual for Morse Stainless Steel Hydra-Lift Karrier Model 400A-72SS-120

Serial Number 0914 to ____ (MMYY)

morsedrum.com

Figure 3.1

WARNING - Watch Out for Pinch Points

Stay clear of moving parts. Operator should

remain behind the push handle during the lift

operation.

Floor Lock

The step-down oor lock is located behind the base (gure

3.1). To activate, step down on the oor lock until it locks

in down position. When oor lock is activated it prevents

unwanted free wheeling of unit. Floor conditions determine

e󰀨ectiveness of oor lock. Operator should verify its holding

action before depending on it to hold.

Drum Holder Assembly

The MORCINCHTM Drum Holder (Saddle) assembly is the

component on intended to hold the drum. It is designed to secure

a standard ribbed 55-gallon (210 liter) steel drum around it’s middle

using a cinch chain and ratchet tightening system. It automatically

adjusts for 22” to 23.5” (56 to 59.7 cm) diameter drum.

The MORCINCHTM Drum Holder also accepts accessories to

handle a plastic drum, ber drum, or a smaller diameter drum.

Figure 2.3

Controls

The Morse Hydra-Lift Karrier is manually propelled and steered. The drum lift is

plug.

There are two functions for the operator to control (Figure 2.3)

1. LIFT and Lower Function for vertical positioning of the drum.

a. Plug the motor into a standard 115V power supply.

b. Turn motor on by holding momentary switch in on position. The drum will

lift.

c. Release momentary switch when drum is at desired height.

d. To lower the drum: With the motor o󰀨, push in the LOWER handle.

2. TILT Function to control the degree of rotation of the drum.

a. Pull down on one side of chain, rotating drum to angle required for

pouring.

b. For best control of drum pouring angle, pay out one side of the chain loop

while pulling in the other side. This helps you to hold back the drum rotation

if the contents of the drum shift.

c. The pull chain pin on the corner of the overhead assembly can be used to

prevent drum rotation. Simply “tie-o󰀨” the chain by engaging in into the pin.

If the drum handler is equipped with the MORStop Tilt-Brake, there is no

need to hold tension on both sides of the chain loop. Braking is immediate

and self-actuating, without additional steps by the operator. To add the

MORStop Tilt-Brake to your drum handler, order part # 3900SS-P for a eld

installation kit.

The Specialist In Drum Handling Equipment

Model 400A-72SS-120

Stainless Steel Hydra-Lift,

72”, AC Power Lift, Manual Tilt

Operator’s Manual for Morse Stainless Steel Hydra-Lift Karrier Model 400A-72SS-120

Serial Number 0914 to ____ (MMYY)

morsedrum.com

CAUTION – Do NOT Transport with Drum Raised

ALWAYS LOWER DRUM HOLDER TO LOWEST POSITION BEFORE TRANSPORTING.

Unit can become unstable when transporting with a raised load.

5.) Lift drum to desired pouring height. Operate the tilt control as described in “Machine Description - Controls” to adjust

the drum attitude. This is especially important when lifting an open drum. The oor lock should be engaged while

dispensing / draining.

6.) When dispensing is complete, tilt drum back to upright position. Disengage the oor lock and lower the drum to

transporting height; about 6” (15 cm) o󰀨 the oor.

WARNING - Stay Clear of Raised Drum

NEVER allow anyone to be below any part of a raised drum handler or drum. Remain behind

the push handle while handling a drum.

WARNING – Do NOT Disengage Cinch Chain When Drum is o󰀨 the Ground

When drum is in upright position, lower drum to oor before releasing cinch chain.

7.) Push unit to drum storage area and lower drum to oor in upright position. Release cinch chain from ratchet by applying

pressure to ratchet handle in a clockwise direction with one hand and opening pawl to free ratchet with the other hand.

Remove cinch chain link from ratchet.

START-UP Procedure

Machine is shipped with hydraulic uid.

1. Install provided hydraulic control levers (threaded rods with black ball handles).

2. IMPORTANT: BEFORE operation, remove RED shipping plug from hydraulic reservoir, and replace with provided

BLACK breather.

Operating Instructions

1.) Push Hydra-Lift Karrier to drum.

2.) Using “LIFT” control as described in “Machine Description -

Controls”, position drum holder assembly with back band at

middle of drum (Figure 3.1). With ratchet plate swung open

and cinch chain hanging from chain hook, push unit until back

band rests rmly against drum. Some adjustment to tilt angle

of saddle may be necessary to ensure band ts ush on drum.

3.) Attaching the drum:

Drape chain across front of drum and engage a link into notch

in ratchet (Figure 3.2). Turn ratchet clockwise to tighten chain.

If ratchet turns until the pawl is beyond last ratchet tooth,

turn ratchet back and slide next link into ratchet notch and try

tightening again. Chain must be held tightly against drum with

pawl engaged securely in ratchet teeth.

4.) Operate lift function to lift drum clear of oor. Roll to

dispensing location. NOTE: Do NOT allow drum to impact on

oor, pouring station, etc. or a spill or damage could occur. Figure 3.2

The Specialist In Drum Handling Equipment

Model 400A-72SS-120

Stainless Steel Hydra-Lift,

72”, AC Power Lift, Manual Tilt

Operator’s Manual for Morse Stainless Steel Hydra-Lift Karrier Model 400A-72SS-120

Serial Number 0914 to ____ (MMYY)

morsedrum.com

Maintenance

Periodic inspection for the general condition of structural and mechanical components is imperative for safe and e󰀩cient

operation.

Periodically inspect all moving parts, framework, and contact areas for signs of wear, fatigue, or loosening. Tighten, adjust,

or replace parts as necessary to prevent failure and maintain proper function.

Inspect the hydraulic system for oil drips, hose damage, or other signs of wear. Inspect the level and condition of the

hydraulic uid. Replace any parts that show signs of wear.

Grease wheel bearings periodically. Oil or grease all moving parts including: the three clevis pins and the surfaces of the

boom which contact the inside of the mast cap, the hinge pin, the gears and sprockets in the tilt drive, and the ratchet and

pawl.

Worn or damaged parts must be properly replaced with the correct, genuine Morse parts.

Hydraulic pump is shipped lled with Noco Premium plus automatic transmission uid d/m. Material safety data sheet

(msds) is available online. Change oil yearly, sooner depending on dirty conditions or outdoor use. Replace oil with Mobil

dte 24 or equivalent for indoor use (Mobil dte 13 for outdoor use).

Inhaltsverzeichnis

Andere morse Hebesystem Handbücher

morse

morse 285A-HD Bedienungsanleitung

morse

morse 525-T-115 Bedienungsanleitung

morse

morse 520-115 Bedienungsanleitung

morse

morse 400A-96-127 Bedienungsanleitung

morse

morse 400A-60-127 Bedienungsanleitung

morse

morse 400AM-72-124 Bedienungsanleitung

morse

morse 400AM-96-114 Bedienungsanleitung

morse

morse 400A-96-115 Bedienungsanleitung

morse

morse 905 Bedienungsanleitung

morse

morse 510SS-115 Bedienungsanleitung

morse

morse 285AM Bedienungsanleitung

morse

morse 195 Series Bedienungsanleitung

morse

morse 400AM-72-114 Bedienungsanleitung

morse

morse 456 Series Bedienungsanleitung

morse

morse 515-N-110 Bedienungsanleitung

morse

morse 400A-96SS-115 Bedienungsanleitung

morse

morse 525-N Bedienungsanleitung

morse

morse 86 Bedienungsanleitung

morse

morse Hydra-Lift 400A-60 Bedienungsanleitung

morse

morse 510M-124 Bedienungsanleitung

morse

morse 515SS-N-110 Bedienungsanleitung

morse

morse 515-N Bedienungsanleitung

morse

morse 515-N-115 Bedienungsanleitung

morse

morse 81-SS Bedienungsanleitung

Beliebte Hebesystem Handbücher anderer Marken

Braun

Braun NL955 Series Bedienungsanleitung

haacon

haacon 1889.10 Bedienungsanleitung

Protekt

Protekt AT 252 Bedienungsanleitung

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Bedienungsanleitung

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Bedienungsanleitung

Genie

Genie Z-60/34 Bedienungsanleitung

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Bedienungsanleitung

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Bedienungsanleitung

Custom Equipment

Custom Equipment Hy-Brid 3 Series Programmierhandbuch

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Programmierhandbuch

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Programmierhandbuch

BERG

BERG BeNomic EasyLeaf Bedienungsanleitung

Powermate

Powermate LiftGate LG-3 Bedienungsanleitung

Snorkel

Snorkel TM12 Series Bedienungsanleitung

Terberg

Terberg OMNIDEKA Bedienungsanleitung

Harmar Mobility

Harmar Mobility AL625 Betriebsanleitung

Rotary

Rotary SPO16 Bedienungsanleitung

Ricon

Ricon Mirage F9T Bedienungsanleitung

morse 400A-72SS-120 Bedienungsanleitung

Beliebte Hebesystem Handbücher anderer Marken