Morso 553 Bedienungsanleitung

MORSØ JERNSTØBERI A/S . DK-7900 NYKØBING MORS

E-Mail: [email protected] · Website: www.morsoe.com

Panther - Gas Stoves

Model No. 553

OWNER’S GUIDE

This appliance meets the requirements of the European Gas Directive

This guide is intended to help you care for your morsø gas stove.

It gives sufcient details to enable your gas stove to be operated and maintained

Please read carefully before using your gas stove and keep for future reference

Please keep your Owner Guide in a safe place together

with the Installation Instructions

Distributed by: Morsø UK

Valley Drive · Swift Valley · Rugby, Warks CV21 1TW · England

As supplied, this appliance is for use with natural gas (G20)

When coverted using conversion kit no. 555311 this appliance is for use

with propane gas (G31)

This appliance is for use in the United Kingdom (GB) and the Republic of

Ireland (IE) only.

C u s t o m e r C a r e

Thank you for choosing morsø.

All morsø stoves are designed to meet the most stringent quality, perform-

ance and safety requirements to provide our customers with many years’

trouble-free service.

Your owner guide aims to improve your understanding and appreciation

of your gas ﬁre by providing simple and informative instructions to ensure

that you beneﬁt from the excellent performance and features it has to

offer.

If you require further assistance or any advice about gas in general, our

service department will be pleased to help.

In the United Kingdom please telephone 0345-626341.

In the Republic of Ireland please telephone 353 183 75114

IF YOU SMELL GAS

DON’T SMOKE

EXTINGUISH ALL NAKED FLAMES

DON’T TURN ELECTRICAL SWITCHES ON OR OFF

TURN OFF THE GAS SUPPLY AT THE METER

OPEN DOORS AND WINDOWS TO GET RID OF THE GAS

IMMEDIATELY CALL THE GAS EMERGENCY SERVICE - SEE YOUR

LOCAL TELEPHONE DIRECTORY

1. As with any gas appliance, this stove must be installed by a compe-tent

person. In the United Kingdom, installation must be in accordan-ce with

the latest edition of the Gas Safety (installation & use) Regulations. In the

Republic of Ireland, installation must be in accordance with all na-tional

and local regulations in force.

2. If the ﬁre is intended to be installed to a chimney which was previusly

used for solid fuel, please note that the chimney must be swept prior to

installation.

3. On no account must the stove stand on carpets or other combustible

materials. The ﬁre must stand on a non-combustible hearth surface. The

hearth material must be at least 600mm wide x 500mm deep x12mm

thick.

4. Clearances to combustible and non-combustible surfaces must be at

least those shown in ﬁgure 1. Please bear this in mind if altering the

room.

5. Never put any paper or other material on the stove. Never add any extra

coals above the number stated in these instructions. This could cause

a safety hazard.

6. The cast iron top, front, rear and sides of this stove are considered to

be working surfaces and so will become very hot when in use. Always

take care when using this appliance. A suitable guard which complies

with BS 6539 or 6778 should be used for the protection of young chil-

dren, the elderly and the inﬁrm. Such a guard is also recommended for

the protection of pet animals.

7. Always switch the stove off and allow to cool before handling. Note

that this stove retains heat for some time after it has

been

swit

ched

off.

8. Never place clothing, towels or any other fabrics on or over the ﬁre.

9. This appliance is ﬁtted with a device which will automatically shut off

Figure 1

the supply of gas to the ﬁre if, for any reason, the ﬂames go out. If this

device does operate or if the ﬁre is turned off accidentally or intention-

ally, always wait three minutes before attempting to relight.

10.This stove must never be used with the windows open or with either

glass panel damaged or removed. The windows should always be se-

cured with the locking screw (See “Cleaning your stove”). If either win-

dow is damaged or will not close securely the ﬁre must be turned off

and not used until the window is changed or corrected by a competent

service engineer.

11.If the house is left unoccupied for a long period we recommend that the

stove is turned fully off.

PLEASE NOTE

When operating your stove for the ﬁrst time, some vapours may be given

off which may cause a slight odour and could possibly set off any smoke

alarms in the immediate vicinity. These vapours are quite normal with

new appliances. They are totally harmless and will disappear after a few

hours use.

This ﬁre is supplied with ceramic “coals” to simulate a real coal ﬁre. After

some use, the ﬁrebox walls and coals may change colour. This is quite

normal.

The Flame Sensing & Flue Blockage Safety System.

For your safety, this appliance is ﬁtted with a ﬂue blockage safety device that

will shut down the appliance in the event of abnormal ﬂue conditions.

This device is NOT a substitute for an independently mounted Carbon

Monoxide detector.

The device will also automatically shut off the gas supply to the ﬁre if the

pilot ﬂame goes out for any reason. If the device starts to shut off the gas

frequently, get expert advice.

The system incorporates a probe that senses that the heat from the pilot

ﬂame is correct. If this probe is cool, the device will prevent any gas ﬂow

unless the control knob is kept depressed at the PILOT/IGN position.

If, for any reason, the ﬂames go out when the ﬁre is hot or if the ﬁre is turned

off when hot, always wait at least three minutes before attempting to

relight.

Always make sure that the windows are securely closed before light-

ing.

To Light The Pilot

- Push in the right control knob (the pilot lighting knob) and, while keeping

it depressed, turn anticlockwise throughThe ignition position marked

and up to the pilot position marked . The spark should light the

pilot. The pilot ﬂame can be seen by looking through the gap in the left

front coal – See ﬁgure 3.

- When the pilot has lit, keep the right hand control knob depressed for

a few seconds to prevent the ﬂame supervision device from shutting

off the gas supply while its probe warms up, as explained above, then

release it.

- If the pilot does not remain alight turn the knob back to the off position

marked •. Wait a few seconds and repeat the lighting sequence.

To Light the Main Burner

- Partially depress the right control knob and turn to the main burner

position marked The main burner should now light.

- The left-hand knob burner is for ﬂame adjustment. Turning it anti-clock-

wise should gradually increase the ﬂame height and heat output. Turning

clockwise reduces the ﬂame height and heat output.

- The burner ﬂame control does not have to be re-set every time the ﬁre

is lit. Once set, it can be left at that position allowing you to use the

right hand control only to ignite the burner at the set ﬂame height.

OPERATING YOUR STOVE

To Turn Off the Main Burner Only

- Turn the right hand control knob to the pilot position marked .

To Turn Off the Main Burner and Pilot

- Turn the right hand control knob to the pilot position marked . Push the

knob in at this position and turn to the off position marked

•.

Figure 2

Figure 3

Opening the Windows

The windows are secured with a locking screw.

Remove the screw using the special key sup-

plied with the stove. See ﬁgure 4. Always

secure the windows with the locking screw

to prevent personal injury or damage while

the stove is in use.

CLEANING YOUR STOVE

Turn the stove off and allow it to cool before attempting any cleaning.

Note that it will retain heat for some time after it has been turned off.

Cast Iron Surfaces

Regular dusting with a dry cloth is all that should normally be necessary.

Any light stains should be removed with a damp cloth. Make sure that the

stove surfaces are completely dry before lighting.

If the paint needs retouching, allow the stove to cool completely. Brush any

areas needing attention with a wire brush (Not enamelled surfaces). Clean off

any loose matter. Touch up with DANWIB aps high temperature stove paint.

Apply the paint sparingly. Two light coats are better than one thick coat.

The Glass Windows

Any stains on the glass can be removed with a non-abrasive cleaner such as

a ceramic hob cleaner. Never use abrasive cleaners. Clean the windows

carefully in accordance with the instructions supplied with the cleaner.

Ceramic Fuel Pieces and Firebox Walls

This appliance uses ﬁrebox walls and fuel effect pieces containing Refractory

Ceramic Fibres (RCF), which are man-made vitreous silicate ﬁbres. Excessive

exposure to this material may cause temporary irritation to eyes, skin and

respiratory tract. Consequently, it makes sense to take care when handling

these articles to ensure that the release of dust is kept to a minimum.

Light coatings of soot will usually be burnt off during the normal operation

of the ﬁre. Should any soot accumulation become excessive, the fuel effect

pieces should be removed from the ﬁre for cleaning. The front and rear base

coals are fragile and should be handled carefully. Cleaning should be carried

out in a well ventilated area or in the open air by gently brushing with the

Figure 4

Figure 5

pieces held away from your face so that you avoid inhaling the dust. We do

not recommend the use of a normal domestic vacuum cleaner which may

blow dust back into the air. We suggest that you remove the coals in the

reverse order to that shown in the fuel bed reﬁtting instructions.

REFITTING THE CERAMIC WALLS & FUEL PIECES

1. Place the ceramic walls against the ﬁrebox sides. Locate the back

edges of the walls in the tabs at the back corners of the ﬁrebox. See

ﬁgure 5.

2. Place the ceramic rear base coal in position. The front of the coal

must rest behind the two stops at the rear of the burner and not rest

on top of them. See ﬁgure 6.

3. Place the left front coal behind the metal lip at the front of the burner.

See ﬁgure 7.

4. Place the right front coal behind the metal lip at the front of the burn-

er. Its left side should rest over the projection on the left front coal.

See ﬁgures 7 & 8.

5. The double top coals are marked “L” and “R”. Place the coal marked

“L” behind the front left coal. Place the coal marked “R” behind the

front right coal. Place the single coal between the two double coals.

See ﬁgure 9.

7. Close and secure the windows by reﬁtting the locking screw.

Figure 6

Figure 7

Figure 8

Figure 9

MAINTENANCE & SERVICING

Regular maintenance

In order to achieve and maintain high levels of personal safety and

performance efﬁciency, it is essential that the ﬂue is kept clear of any form

of obstruction.

In the United Kingdom it is the law that a landlord must have any gas appli-

ance, ﬂue and pipework which is situated in a tenant’s premises checked

for safety at least every twelve months by a competent person (In the U.K.,

a CORGI registered installer).

We recommend that all gas appliances and their ﬂues, wherever situated,

are checked annually.

Servicing

• In the United Kingdom servicing can be carried out either by a Wonderﬁre

Service engineer or a CORGI registered installer.

• If you require your ﬁre to be serviced by a Wonderﬁre Service engineer

please contact the Wonderﬁre service department on 345 626 341 and

quote the following details;

a) - model name and number.

b) - appliance serial no.

• In Republic of Ireland call 353 183 75114 for all enquiries.

• If you wish to replace any of the owner replaceable parts listed on page

11, please contact your dealer or the Wonderﬁre service department for

your nearest stockist of these parts. When ordering please quote the part

number shown.

Andere Handbücher für 553

Inhaltsverzeichnis

Andere Morso Herd Handbücher

Morso

Morso SQUIRREL 551 Bedienungsanleitung

Morso

Morso Panther Bedienungsanleitung

Morso

Morso 3112 Bedienungsanleitung

Morso

Morso 3400 Series Bedienungsanleitung

Morso

Morso 7800 Series Bedienungsanleitung

Morso

Morso S11-40 Bedienungsanleitung

Morso

Morso 6100 series Bedienungsanleitung

Morso

Morso 3600 Series Bedienungsanleitung

Morso

Morso 6870 Bedienungsanleitung

Morso

Morso 3610 Stücklistenhandbuch

Morso

Morso 1416 Bedienungsanleitung

Morso

Morso 1410 Bedienungsanleitung

Morso

Morso S11 Series Bedienungsanleitung

Morso

Morso P31 Bedienungsanleitung

Morso

Morso S50 Bedienungsanleitung

Morso

Morso 7400 SERIES Bedienungsanleitung

Morso

Morso SQUIRREL 552 Bedienungsanleitung

Morso

Morso 6191 Bedienungsanleitung

Morso

Morso 7600 series Bedienungsanleitung

Morso

Morso 3440 Bedienungsanleitung

Morso

Morso 8100 series Bedienungsanleitung

Morso

Morso S11-40 Bedienungsanleitung

Morso

Morso 1410 Bedienungsanleitung

Morso

Morso 553 Bedienungsanleitung

Beliebte Herd Handbücher anderer Marken

Arada

Arada Cassette Stove Bedienungsanleitung

Parmco

Parmco FS 600 Bedienungsanleitung

MCZ

MCZ SUITE AIR 10 M2 Bedienungsanleitung

HearthStone

HearthStone Stowe DV 8321 Fehlerbehebungshandbuch

Cattara

Cattara FAMILY Bedienungsanleitung

Stanley

Stanley Argon F500 OVAL Bedienungsanleitung

Avalon

Avalon B-VENT Bedienungsanleitung

Nordpeis

Nordpeis Vega Bedienungsanleitung

Exquisit

Exquisit EKC601-5 Bedienungsanleitung

Stanley

Stanley Oisin Oil MK II Betriebsanleitung

Thermocet

Thermocet Brookfield S/CC Bedienungsanleitung

HASE

HASE delhi Bedienungsanleitung

Vermont Castings

Vermont Castings Intrepid 2 Bedienungsanleitung

Italiana Camini

Italiana Camini CLASSICA Kurzanleitung

Avalon

Avalon Vashon Avanti DVS FS Bedienungsanleitung

Spartherm

Spartherm ambiente a1 Bedienungsanleitung

Dimplex

Dimplex MCFSTV12AU Bedienungsanleitung

Warmlite

Warmlite WL46040 Bedienungsanleitung