Motorline professional TEC100 Bedienungsanleitung

V3.0

REV. 01/2019

TEC100 EN

USER/INSTALLER MANUAL

A B

ENEN

STANDARDS TO FOLLOW

PRODUCT PROFILE

PRODUCT INSTALLATION

QUICK REFERENCE PROGRAMMING GUIDE

USER SETTINGS

LEAD WIRE DESCRIPTION

SOUNDS AND LIGHTS

DOOR SETTINGS

RESET TO FACTORY DEFAULT

ANTI TAMPER ALARM

ACCESS CONTROL THROUGH CODE (MCA)

CABLING DIAGRAM

. SAFETY INSTRUCTIONS

. PRODUCT

. INSTALLATION

. PROGRAMMING

. DETAILED PROGRAMMING GUIDE

. CABLING

. ACOUSTO-OPTIC INSTRUCTIONS

. CONTENT . SAFETY INSTRUCTIONS

INDEX STANDARDS TO FOLLOW

TECHNICAL PARAMETERS

ATTENTION:

This product is certified in accordance with European Community

(EC) safety standards.

This product complies with Directive 2011/65/EU of the European

Parliament and of the Council, of 8 June 2011, on the restriction of

the use of certain hazardous substances in electrical and electronic

equipment.

(Applicable in countries with recycling systems).

This marking on the product or literature indicates that the product

andelectronicaccessories(eg.Charger,USBcable,electronicmaterial,

controls, etc.) should not be disposed of as other household waste at

the end of its useful life. To avoid possible harm to the environment

or human health resulting from the uncontrolled disposal of waste,

separate these items from other types of waste and recycle them

responsibly to promote the sustainable reuse of material resources.

Home users should contact the dealer where they purchased this

product or the National Environment Agency for details on where and

how they can take these items for environmentally safe recycling.

Business users should contact their vendor and check the terms and

conditions of the purchase agreement. This product and its electronic

accessories should not be mixed with other commercial waste.

This marking indicates that the product and electronic accessories

(eg. charger, USB cable, electronic material, controls, etc.) are

susceptible to electric shock by direct or indirect contact with

electricity. Be cautious when handling the product and observe all

safety procedures in this manual.

A B

ENEN

. SAFETY INSTRUCTIONS . PRODUCT

STANDARDS TO FOLLOW PRODUCT PROFILE

TECHNICAL PARAMETERS

Theunit is single door multifunction standaloneaccesscontrollerora Wiegand output keypad

or card reader. It is suitable for mounting either indoor or outdoor in harsh environments. It

is housed in a strong, sturdy and vandal proof Zinc Alloy electroplated case which is available

in either a bright silver or matt silver finish. The electronics are fully potted so the unit is

waterproof and conforms to IP68. This unit supports up to 2000 users in either a Card, 4 digit

PIN, or a Card + PIN option. The inbuilt card reader supports 125KHZ EM cards,13.56MHz Mifare

cards. The unit has many extra features including lock output current short circuit protection,

Wiegand output , and a backlit keypad. These features make the unit an ideal choice for

door access not only for small shops and domestic households but also for commercial and

industrial applications such as factories, warehouses, laboratories, banks and prisons.

• Waterproof, conforms to IP68

• Strong Zinc Alloy Electroplated anti-

vandal case

• Full programming from the keypad

• 2000 uses, supports Card, PIN, Card + PIN

• Can be used as a stand alone keypad

• Backlight keys

• Wiegand 26 input for connection to

external reader

• Wiegand 26 output for connection to a

controller

• Adjustable Door Output time, Alarm time,

Door Open time

• Very low power consumption (30mA)

• Fast operating speed, <20ms with 2000

users

• Lock output current short circuit

protection

• Easy to install and program

• Built in light dependent resistor (LDR) for

anti tamper

• Built in buzzer

• Red, Yellow and Green LEDS display the

working status

• Work Voltage ac&dc 9-28V

• Static Current <30mA

• Reading Range 3-8cm

• Capacity 2000 users

• Ambient Temperature -25~55C

• Ambient Humidity 10% ~ 90%

• Electricity lock output <3A

• Alarm output <20A

• Output short circuit protection time <100S

• Open time 0 ~ 99 seconds (adjustable)

• It is important for your safety that these instructions are followed.

• Keep these instructions in a safe place for future reference.

• The ELECTROCELOS S.A. is not responsible for the improper use of the product,

or other use than that for which it was designed.

• The ELECTROCELOS S.A. is not responsible if safety standards were not taken

into account when installing the equipment, or for any deformation that may

occur.

• The ELECTROCELOS S.A. is not responsible for insecurity and malfunction of the

product when used with components that were not sold by the them.

• This product was designed and manufactured strictly for the use indicated in

this manual.

• Any other use not expressly indicated may damage the product and/or can

cause physical and property damages, and will void the warranty.

• Do not make any changes to the automation components and/or their

accessories.

• The customer shall not, under any circumstances, attempt to repair or tune the

automatism. Must call qualified technician only.

•Theinstallermusthavecertifiedprofessionalknowledgeatthelevelofelectronic.

He should also be able to perform electrical connections in compliance with all

applicable regulations.

• The installer should inform the customer how to handle the product in an

emergency and provide him the manual.

• This device can be used by children 8 year old or older and persons whose

physical, sensory or mental capacities are reduced, or by persons without

experience or knowledge if they have received supervision or instructions on

the use of the device in a safe manner and understood the hazards involved.

Children should not play with the device. Cleaning and maintenance by the user

must not be carried out by unsupervised children.

• Automatism powered by very low safety voltage, with electronic board/control

board/control unit.

• Before installing, the installer must verify that the temperature range indicated

on the automatism is appropriate to the location of the installation.

• In order to protect the electrical cables against mechanical stress, you should

use conduit for the electrical wires, essentially on the power cable.

A B

88mm 27mm

122mm

ENEN

. INSTALLATION

PRODUCT INSTALLATION PRODUCT INSTALLATION

. INSTALLATION

1 • Apply the drilling diagram (B) to the

desired installation place.

3 • Using the hex key (C), loosen the screw in

totality and remove the back cover.

5 • Insert the cable into the hole.2 • Make the holes:

F - TEC100 ﬁxing holes;

G - hole to pass the cable.

4 • Insert the bushings, place the back cover

and tighten totally the screws.

BUSHING

SCREW

6 • Attach the body of the TEC100 to the

back cover, insert the screw and tighten

completely.

A • TEC100

B • Drilling diagram

C • Hex key

D • Screws

E • Bushings

Caption

A B

ENEN

To enter the programming mode 999999 is the default factory master code

To exit from the programming

mode

Note that to undertake the following programming the master user must be logged in

To change the master code The master code can be 6 to 8 digits long

Setting the working mode:

Set valid card only users

Set valid card and PIN users

Set valid card or PIN users

Entry is by card only

Entry is by card and PIN together

Entry is by either card or PIN (default)

To add a user in either card or PIN mode, i.e. in the mode. (Default setting)

To add a PIN user

The ID number is any number between 1 & 2000. The

PIN is any four digits between 0000 & 9999 with the

exception of 1234 which is reserved. Users can be

added continuously without exiting programming

mode as follows:

To delete a PIN user

Users can be deleted continuously without exiting

programming mode

To change the PIN of a PIN user

(This step must be done out of

programming mode)

. PROGRAMMING

QUICK REFERENCE PROGRAMMING GUIDE

. DETAILED PROGRAMMING GUIDE

USER SETTINGS

To enter the programming mode 999999 is the default factory master code

To exit from the programming

mode

Note that to undertake the following programming the master user must be logged in

To change the master code The master code can be 6 to 8 digits

To add a PIN user

The ID number is any number between 1 & 2000. The

PIN is any four digits between 0000 & 9999 with the

exception of 1234 which is reserved. Users can be

added continuously without exiting programming mode

To add a card user Cards can be added continuously without exiting

programming mode

To delete a PIN or a card user

Users can be deleted continuously without exiting

programming mode

To unlock the door for a PIN user Enter the then press

To unlock the door for a card user Present the card

Master code

*#Master code

Read card

User ID number

#03

#13

#23

Read card

New code New code

0# #

User ID number PIN

1# #

User ID number

Use ID number

1 # PIN #

User ID no 1 User ID no 2

1 # PIN # #

PIN #

ID number

* # Old PIN #

New PIN New PIN

# #

for PIN user or

for a card user

New code

0##

New code

A B

ENEN

To add a card user (Method 1)

This is the fastest way to enter

cards, user ID number auto

generation Cards can be added continuously without exiting

programming mode

To add a card user (Method 2)

This is the alternative way to

enter cards using User ID

Allocation. In this method a User

ID is allocated to a card. Only

one user ID can be allocated to a

single card User can be added continuously without exiting

programming mode

To add a card user (Method 3)

Card number is the last 8

digits printed on the back of

the card,user ID number auto

generation User can be added continuously without exiting

programming mode

To add a card user (Method 4)

In this method a User ID is

allocated to a card number. Only

one user ID can be allocated to

the card number User can be added continuously without exiting

programming mode

To delete a card user by card.

Note users can be deleted

continuously without exiting

programming mode

To delete a card user by user ID.

This option can be used when a

user has lost their card

To delete a card user by card

number.

This option can be used when the

user want to make the change but

the card has lost Note users can be deleted continuously without

exiting programming mode

To add a card and PIN user in card and PIN mode ( )

To Add a card and Pin user

(The PIN is any four digits

between 0000 & 9999 with

the exception of 1234 which is

reserved.)

Add the card as for a card user

Press to exit from the programming mode

Then allocate the card a PIN as follows:

To change a PIN in card and PIN

mode (Method 1) Note that this is

done outside programming mode

so the user can undertake this

themselves

To change a PIN in card and PIN

mode (Method 2) Note that this is

done outside programming mode

so the user can undertake this

themselves

To delete a Card and PIN user just

delete the card

To add a card user in card mode ( )

To Add and Delete a card user The operating is the same as adding and deleting a

card user in

To delete All users

To delete ALL users. Note that this

is a dangerous option so use with

care

To unlock the door

For a PIN user Enter the then press

For a card User

For a card and PIN user then enter

Read card

Card number

Read Card

User ID

0000

Card number

Read card #

ID number

Card number #

ID number

#13

#03

#23

Read card

*# # #

1234 PIN PIN

Read card

Old PIN New PIN

# #

New PIN

ID number

Old PIN New PIN

# #

New PIN

USER SETTINGS USER SETTINGS

. DETAILED PROGRAMMING GUIDE . DETAILED PROGRAMMING GUIDE

A B

ENEN

Relay Output Delay Time

To set door relay strike time 0-99 is to set the door relay time 0-99 seconds

Door Open Detection

Door Open Too Long (DOTL) warning. When used with an optional magnetic contact or

built-in magnetic contact of the lock, if the door is opened normally, but not closed after

1 minute, the inside buzzer will beep automatically to remind people to close the door

and continue for 1 minute before switching off automatically.

Door Forced Open warning. When used with an optional magnetic contact or built-in

magnetic contact of the lock, if the door is forced open, or if the door is opened after 20

seconds ,the inside buzzer and alarm output will both operate. The Alarm Output time is

adjustable between 0-3 minutes with the default being 1 minute.

To disable door open detection.

(Factory default)

To enable door open detection

Alarm output time

To set the alarm output time

(0-3 minutes) Factory default is 1

minute

Keypad Lockout & Alarm Output options. If there are 10 invalid cards or 10 incorrect

PIN numbers in a 10 minute period either the keypad will lockout for 10 minutes or both

the alarm and the inside buzzer will operate for 10 minutes, depending on the option

selected below.

Normal status: No keypad lockout

or alarm (factory default) (Factory default setting)

Keypad Lockout

Alarm and inside buzzer operate

To remove the alarm

To reset the Door Forced Open

warning or

To reset the Door Open Too Long

warning Close the door or

1• Disconnect power from the unit

2• Press and hold # key whilst powering the unit back up

3• On hearing two “Di” release # key, system is now back factory settings

Please note only installer data is restored, user data will not be affected

The unit uses a LDR (light dependent resistor) as an anti tamper alarm. If the keypad is

removed from the cover then the tamper alarm will operate.

Master Code #

Read valid card

Master Code #

Read valid card

#06

#16

#07

#17

#27

#0~35

DOOR SETTINGS DOOR SETTINGS

RESET TO FACTORY DEFAULT

ANTI TAMPER ALARM

. DETAILED PROGRAMMING GUIDE . DETAILED PROGRAMMING GUIDE

value #

master code # 4

A B

ENEN

ACCESS CONTROL THROUGH CODE (MCA)

. GUIA DE PROGRAMAÇÃO AVANÇADA .

ACCESS CONTROL THROUGH CODE (MCA)

. DETAILED PROGRAMMING GUIDE

1 • Access "Operation" and select the "tools"

tab.

2 • Press "extended function".

3 • Enter the password 5678.

5 - Press "ok".

4 • Go to "Configuration" and select "Activate access keypad".

When to Use

When there is an MCA connected with a

TEC100 to operate only with code, we need

to follow the following steps to register

inputs and outputs.

NOTE: For the changes to take effect, you must restart the device.

A B

ENEN

ACCESS CONTROL THROUGH CODE (MCA)

. DETAILED PROGRAMMING GUIDE

ACCESS CONTROL THROUGH CODE (MCA)

. DETAILED PROGRAMMING GUIDE

9 • Select the user you want to give privilege and click on "Access Privilege".

10 • The box to add / remove doors to the user appears.

11 • To finish this edition press "Confirm and upload".

12 • Now access the "Pwd MGT" tab to set the type of access you want (PIN-Card).

6 • Access "Configuration" and select the "Personnel" tab.

7 • Press "Edit" or double-click on the person.

8 • Fill in the requested data and press "ok". Later, to identify yourself, you will

have to enter the Card Number and PIN, eg * 14 # 123456.

A B

ENEN

. ACOUSTO-OPTIC INSTRUCTIONS

OPERATION STATE RED LIGHT GREEN LIGHT BUZZER NOTE

Standby Slow ﬂashing Off

Buttons Di

Success Off On Di—

Failure Di Di Di

Into programming On Off Di— Indicator is

orange

Set condition On On

Exit programming Slow ﬂash Off Di—

Unlock Off On Di—

Alarm Fast ﬂashing Off Alarm sound 

. CABLING

LEAD WIRE DESCRIPTIONSOUNDS AND LIGHTS

Line

sequence Marks Color Function description

1BELL_A Pink Doorbell button one end

2BELL_B Light pink The doorbell button to the other end

3D Green WG output line D

4D White WG output line D

ALARM Grey Alarm negative (alarm positive

connected   v

OPEN Yellow Exit button one end (Exit button the other end

connected GND)

D_IN Brown Magnetic switch one end (magnetic switch

another end connected GND)

AC&DC Red Power supply -V input (DC input)

AC&DC Black Power supply -V input (DC input -)

 NO Blue Relay NO

 COM Purple Relay common

 NC Orange Relay NC

Andere Handbücher für TEC100

Inhaltsverzeichnis

Andere Motorline professional Tastenfeld Handbücher

Motorline professional

Motorline professional MHACA12PMBE Bedienungsanleitung

Beliebte Tastenfeld Handbücher anderer Marken

BFT

BFT SELETTO Bedienungsanleitung

Micro Id

Micro Id MP7G3BL Gebrauchsanweisung

WindowMaster

WindowMaster WLI 130 Bedienungsanleitung

ACT

ACT ACT PRO 1030 Bedienungsanleitung

Cardin

Cardin SSB Series Bedienungsanleitung

Harman Kardon

Harman Kardon KP 1 Bedienungsanleitung

Chamberlain

Chamberlain KPR2000 Benutzerhandbuch

CYP

CYP CR-KP1 Bedienungsanleitung

Aeware

Aeware k-35 Series Referenzhandbuch

Aritech

Aritech CS-175 Series Bedienungsanleitung

GE NetworX NX-1600E Series Bedienungsanleitung

Lenze AC Tech

Lenze AC Tech MC SERIES Bedienungsanleitung

Burg Wächter

Burg Wächter secuENTRY 7711 Bedienungsanleitung

Aeware

Aeware in.k450 Bedienungsanleitung

Lenze

Lenze EPM-H410 Bedienungsanleitung

Toshiba

Toshiba RKP007Z Bedienungsanleitung

Gemini

Gemini GEM-DXK1 KEYPAD Bedienungsanleitung

Russound

Russound MDK-C5 Betriebsanleitung