Motorola MC319Z RFID Betriebsanleitung

MC319Z RFID

Regulatory Guide

Microsoft®Mobile®6.5

2 MC319Z RFID

Zebra reserves the right to make changes to any product to improve reliability,

function, or design.

Zebra does not assume any product liability arising out of, or in connection with,

the application or use of any product, circuit, or application described herein.

No license is granted, either expressly or by implication, estoppel, or otherwise

under any patent right or patent, covering or relating to any combination, system,

apparatus, machine, material, method, or process in which Zebra products might

be used. An implied license exists only for equipment, circuits, and subsystems

contained in Zebra products.

Zebra and the stylized Zebra head are trademarks of ZIH Corp., registered in

many jurisdictions worldwide. All other trademarks are the property of their

respective owners.

Zebra Technologies Corporation

Lincolnshire, IL U.S.A.

http://www.zebra.com

Warranty

For the complete Zebra hardware product warranty statement, go to:

www.zebra.com/warranty.

For Australia Only:

This warranty is given by Zebra Technologies Asia Pacific Pte. Ltd., 71 Robinson

Road, #05-02/03, Singapore 068895, Singapore. Our goods come with

guarantees that cannot be excluded under the Australia Consumer Law. You are

entitled to a replacement or refund for a major failure and compensation for any

other reasonably foreseeable loss or damage. You are also entitled to have the

goods repaired or replaced if the goods fail to be of acceptable quality and the

failure does not amount to a major failure.

Zebra Technologies Corporation Australia’s limited warranty above is in addition

to any rights and remedies you may have under the Australian Consumer Law. If

you have any queries, please call Zebra Technologies Corporation at+65 6858

0722. You may also visit our website: http://www.zebra.com for the most updated

warranty terms.

Regulatory Guide 3

Health and Safety Recommendations

Ergonomic Recommendations

Caution: In order to avoid or minimize the potential risk of ergonomic injury follow

the recommendations below. To prevent employee injury, consult with the local

Health & Safety Manager to ensure compliance with the required safety

programs.

• Reduce or eliminate repetitive motion

• Maintain a natural position

• Reduce or eliminate excessive force

• Keep objects that are used frequently within easy reach

• Perform tasks at correct heights

• Reduce or eliminate vibration

• Reduce or eliminate direct pressure

• Provide adjustable workstations

• Provide adequate clearance

• Provide a suitable working environment

• Improve work procedures

Regulatory Information

This guide applies to the following Model Numbers: MC319ZEU, MC319ZUS.

All Zebra devices are designed to be compliant with rules and regulations in

locations they are sold and will be labeled as required.

Local language translations are available at the following website:

www.zebra.com/support.

Any changes or modifications to Zebra equipment, not expressly approved by

Zebra, could void the user's authority to operate the equipment.

Only use Zebra approved and UL Listed accessories, battery packs and battery

chargers.

Do NOT attempt to charge damp/wet mobile computers or batteries. All

components must be dry before connecting to an external power source.

Declared maximum operating temperature: 50 Degrees Centigrade

Radio Devices

This device is approved under the Zebra brand.

Model Numbers for Regulatory Certification:

• MC319ZUS - Frequency 902 - 928 MHz (Maximum)

• MC319ZEU - Frequency 865 - 868 MHz

4 MC319Z RFID

Bluetooth®Wireless Technology

This is an approved Bluetooth® product. For more information or to view End

Product Listing, please visit https://www.bluetooth.org/tpg/listings.cfm.

Wireless Device Country Approvals

Regulatory markings, subject to certification, are applied to the device signifying

the radio is approved for use in the following countries: United States, Canada,

China, S. Korea, Australia, and Europe1.

Please refer to the Zebra Declaration of Conformity (DoC) for details of other

country markings. This is available at www.zebra.com/doc.

Note1: For 2.4GHz or 5GHz Products: Europe includes, Austria, Belgium,

Bulgaria, Czech Republic, Cyprus, Denmark, Estonia, Finland, France, Germany,

Greece, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania,

Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovak

Republic, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.

Operation of the device without regulatory approval is illegal.

Country Selection - Worldwide Version Only

Select only the country in which you are using the device. Any other selection will

make the operation of this device illegal.

Frequency of Operation - FCC

The range of channels is limited by firmware.

Country Roaming - Worldwide Version only

This device incorporates the International Roaming feature (IEEE802.11d) which

will ensure the product operates on the correct channels for the particular country

of use.

Ad-Hoc Operation

Ad-Hoc operation is limited to Channels 36-48 (5150-5250 MHz). Use of this band

is restricted to Indoor Use Only, any other use will make the operation of this

device illegal.

Regulatory Guide 5

Frequency of Operation – FCC and IC

5 GHz Only

The use in the UNII (Unlicensed National Information Infrastructure) band 1

(5150-5250 MHz) and the band 5.470-5.725 MHz is restricted to Indoor Use Only;

any other use will make the operation of this device illegal.

Industry Canada statement:

Caution:

The device for the band 5150-5250 MHz and the band 5.470-5.725 MHz is only

for indoor usage to reduce potential for harmful interference to co-channel mobile

satellite systems.

High power radars are allocated as primary users (meaning they have priority) of

5250-5350 MHz and 5650-5850 MHz and these radars could cause interference

and/or damage to LE-LAN devices.

Avertissement:

Le dispositif fonctionnant dans la bande 5150-5250 MHz, 5.470-5.725 MHz est

réservé uniquement pour une utilisation à l'intérieur afin de réduire les risques de

brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes

canaux.

Les utilisateurs de radars de haute puissance sont désignés utilisateurs

principaux (c.-à-d., qu'ils ont la priorité) pour les bandes 5250-5350 MHz et

5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des

dommages aux dispositifs LAN-EL.

6 MC319Z RFID

Please observe all warning notices with regard to the usage of wireless devices.

Potentially Hazardous Atmospheres

You are reminded of the need to observe restrictions on the use of radio devices

in fuel depots, chemical plants etc. and areas where the air contains chemicals or

particles (such as grain, dust, or metal powders) and any other area where you

would normally be advised to turn off your vehicle engine.

Safety in Aircraft

Switch off your wireless device whenever you are instructed to do so by airport or

airline staff. If your device offers a 'flight mode' or similar feature, consult airline

staff as to its use in flight.

Safety in Hospitals

This device is not part of a life-support system.

Wireless devices transmit radio frequency energy and may affect medical

electrical equipment.

Wireless devices should be switched off wherever you are requested to do so in

hospitals, clinics or healthcare facilities. These requests are designed to prevent

possible interference with sensitive medical equipment.

Pacemakers

Pacemaker manufacturers recommended that a minimum of 15 cm (6 inches) be

maintained between a handheld wireless device and a pacemaker to avoid

potential interference with the pacemaker. These recommendations are

consistent with independent research and recommendations by Wireless

Technology Research.

Persons with pacemakers:

• Should ALWAYS keep the device more than 15cm (6 inches) from their

pacemaker when turned ON.

• Should not carry the device in a breast pocket.

• Should use the ear furthest from the pacemaker to minimize the potential for

interference.

• If you have any reason to suspect that interference is taking place, turn OFF

your device.

Warnings for Use of Wireless Devices

Regulatory Guide 7

Other Medical Devices

Please consult your physician or the manufacturer of the medical device, to

determine if the operation of your wireless product may interfere with the medical

device.

Note: Under certain adverse conditions, interference may be experienced when

using ActiveSync; if this occurs, switch off the terminal and re-start ActiveSync.

Safety Information

Reducing RF Exposure - Use Properly

Only operate the device in accordance with the instructions supplied.

International

The device complies with internationally recognized standards covering human

exposure to electromagnetic fields from radio devices. For information on

“International” human exposure to eletromagnic fields refer to the Zebra

Declaration of Conformity (DoC) at

www.zebra.com/doc.

Europe

For RFID operation, to comply with EU RF exposure requirements, this device

must be operated in the hand with a minimum separation distance of 23cm or

more from a person's body. Other operating configurations should be avoided.

US and Canada

For RFID operation, to satisfy FCC RF exposure requirements, a mobile

transmitting device must operate with a minimum separation distance of 23cm or

more from a person's body.

Co-located Statement

To comply with FCC RF exposure compliance requirement, the antenna used for

this transmitter must not be co-located or operating in conjunction with any other

transmitter/antenna except those already approved in this filing.

RF Exposure Guidelines

8 MC319Z RFID

Industry Canada Statement

IMPORTANT NOTE: (For mobile device use)

Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated with

minimum distance 20cm between the radiator & your body.

NOTE IMPORTANTE: (Pour l'utilisation de dispositifs mobiles)

Déclaration d'exposition aux radiations:

Cet équipement est conforme aux limites d'exposition aux rayonnements IC

établies pour un environnement non contrôlé. Cet équipement doit être installé et

utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et

votre corps.

Laser Devices

Complies with 21CFR1040.10 and 1040.11 except for deviations pursuant to

Laser Notice No. 50, dated June 24, 2007.

EN60825-1: 2007

IEC60825-1 (Ed. 2.0)

The laser classification is marked on one of the labels on the device.

Class 2 laser scanners use a low power, visible light diode. As with any very bright

light source, such as the sun, the user should avoid staring directly into the light

beam. Momentary exposure to a Class 2 laser is not known to be harmful.

Regulatory Guide 9

Scanner Labeling

Power Supply

Use ONLY a LISTED, Type no. 50-14000 (5.4Vdc, 3A), PWRS-14000 (5.4Vdc,

3A), or KT -14000 (5.4V, 3A), direct plug-in power supply, marked Class 2 or LPS

(IEC60950-1, SELV). Use of alternative Power Supply will invalidate any

approvals given to this unit and may be dangerous.

Batteries

Taiwan - Recycling

EPA (Environmental Protection Administration) requires dry

battery producing or importing firms in accordance with Article

15 of the Waste Disposal Act are required to indicate the

recycling marks on the batteries used in sales, giveaway or

promotion. Contact a qualified Taiwanese recycler for proper battery disposal.

⊼ ᛣ˖ᠧᓔᯊঞ㘨䫕༅ᬜᯊ᳝▔ܝ䕤ᇘ ࣓Ⳉ㾚ܝᴳ

COMPLIES WITH 21CFR1040.10 AND 1040.11 EXCEPT FOR

DEVIATIONS PURSUANT TO LASER NOTICE NO. 50,

DATED JUNE 24, 2007 AND IEC 60825-1 (Ed. 2.0) EN60825-1:2007

CAUTION- CLASS 2 LASER LIGHT WHEN OPEN. DO NOT STARE INTO THE

BEAM.

ATTENTION- LUMIÉRE LASER DE CLASSE 2 EN CAS D'OUVERTURE.

NE PAS REGARDER DANS LE FAISCEAU.

VORSICHT- LASERLICHT KLASSE 2, WENN ABDECKUNG GEÖFFNET. NICHT

IN DEN STRAHL BLICKEN.

10 MC319Z RFID

Battery Information

Zebra rechargeable battery packs are designed and constructed to the highest

standards within the industry.

However, there are limitations to how long a battery can operate or be stored

before needing replacement. Many factors affect the actual life cycle of a battery

pack, such as heat, cold, harsh environmental conditions and severe drops.

When batteries are stored over six (6) months, some irreversible deterioration in

overall battery quality may occur. Store batteries at half of full charge in a dry, cool

place, removed from the equipment to prevent loss of capacity, rusting of metallic

parts and electrolyte leakage. When storing batteries for one year or longer, the

charge level should be verified at least once a year and charged to half of full

charge.

Replace the battery when a significant loss of run time is detected.

Standard warranty period for all Zebra batteries is 30 days, regardless if the

battery was purchased separately or included as part of the mobile computer or

bar code scanner.

Battery Safety Guidelines

• The area in which the units are charged should be clear of debris and

combustible materials or chemicals. Particular care should be taken where the

device is charged in a non commercial environment.

• Follow battery usage, storage, and charging guidelines found in the user's

guide.

• Improper battery use may result in a fire, explosion, or other hazard.

• To charge the mobile device battery, the battery and charger temperatures

must be between -4ºF and +122 ºF (- 20 ºC and +50 ºC)

• Do not use incompatible batteries and chargers. Use of an incompatible

battery or charger may present a risk of fire, explosion, leakage, or other

hazard. If you have any questions about the compatibility of a battery or a

charger, contact Zebra support.

• For devices that utilize a USB port as a charging source, the device shall only

be connected to products that bear the USB-IF logo or have completed the

USB-IF compliance program.

• Do not disassemble or open, crush, bend or deform, puncture, or shred.

• Severe impact from dropping any battery-operated device on a hard surface

could cause the battery to overheat.

Do not short circuit a battery or allow metallic or conductive objects to contact

the battery terminals.

Andere Handbücher für MC319Z RFID

Inhaltsverzeichnis

Andere Motorola Barcode-Lesegerät Handbücher

Motorola

Motorola SYMBOL MT2000 Series Bedienungsanleitung

Motorola

Motorola Symbol DS3408 Installations- und Betriebshandbuch

Motorola

Motorola MK500 Bedienungsanleitung

Motorola

Motorola MC32N0 SERIES Bedienungsanleitung

Motorola

Motorola DS9808 - Symbol - Wired Handheld Barcode... Referenzhandbuch

Motorola

Motorola CA50 Bedienungsanleitung

Motorola

Motorola Symbol CS3070 Bedienungsanleitung

Motorola

Motorola MC17 Installations- und Betriebshandbuch

Motorola

Motorola Symbol DS3407 Bedienungsanleitung

Motorola

Motorola Symbol LS3578 Bedienungsanleitung

Motorola

Motorola MX101 Installations- und Betriebshandbuch

Motorola

Motorola DS3508 Installations- und Betriebshandbuch

Motorola

Motorola Symbol CS3000 Series Bedienungsanleitung

Motorola

Motorola MP6000 Montageanleitung

Motorola

Motorola DS4208 Bedienungsanleitung

Motorola

Motorola Symbol LS9208 Installations- und Betriebshandbuch

Motorola

Motorola DS9208 Betriebsanleitung

Motorola

Motorola SYMBOL LS7708 Bedienungsanleitung

Motorola

Motorola Symbol DS6878 Bedienungsanleitung

Motorola

Motorola DS4208 Bedienungsanleitung

Motorola

Motorola LS3408-FZ20005 Installations- und Betriebshandbuch

Motorola

Motorola LI2208 Bedienungsanleitung

Motorola

Motorola SYMBOL DS6707-DP Bedienungsanleitung

Motorola

Motorola SYMBOL LS7708 Installations- und Betriebshandbuch

Beliebte Barcode-Lesegerät Handbücher anderer Marken

POSMicro

POSMicro Datalogic PowerScan D7100 Bedienungsanleitung

Marson

Marson MT780 Kurzanleitung zur Einrichtung

NCR

NCR RealPOS Bedienungsanleitung

Element

Element P130BT Bedienungsanleitung

Meec tools

Meec tools OBD-II / VAG Bedienungsanleitung

SICK

SICK CLP 100 Bedienungsanleitung

Royal Tag SA

Royal Tag SA I-Read Bedienungsanleitung

Welch Allyn

Welch Allyn IMAGETEAM 3800 Bedienungsanleitung

Meteor

Meteor 8310 Bedienungsanleitung

Denso

Denso BHT-500B Bedienungsanleitung

Datalogic

Datalogic Heron HD3130 Bedienungsanleitung

Newland

Newland NLS-HR15-BT Bedienungsanleitung

ARTDEV

ARTDEV AS-1310 Bedienungsanleitung

Aopos

Aopos AS290 Bedienungsanleitung

ENS

ENS 367-5455 Bedienungsanleitung

Atid

Atid AT188N Plus Bedienungsanleitung

AZENTA

AZENTA 281947 Bedienungsanleitung

Datalogic

Datalogic DS2x00N-DS4800 Series Leitfaden