Motorola RFS4010 Series Bedienungsanleitung

RFS4010 Series RF Switch

Installation Guide

MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office.

Symbol is a registered trademark of Symbol Technologies, Inc. All other product or service

1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

2.0 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

3.0 LED Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

4.0 Hardware Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

5.0 Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

6.0 Part Numbers, Support, and Sales . . . . . . . . . . . . . . . . . . . . . 26

7.0 End-User License Agreement . . . . . . . . . . . . . . . . . . . . . . . . . 27

8.0 RFS4010 China ROHS Compliance . . . . . . . . . . . . . . . . . . . . . 30

Contents

Introduction 1

1 Introduction

The Motorola RFS4010 RF Switch is a member of Motorola’s RFS Series Wireless Switch family. The

RFS4010 RF Switch provides centralized Wireless LAN (WLAN) configuration and management by

coalescing a network “intelligence” previously spread across physically distributed access points.

The RFS4010 simplifies deployment of a Wired/Wireless 802.11 a/b/g/n network, for a SME/SMB.

With the integrated Layer 2/Layer 3 Networking Services such as integrated Layer 2 Switching with

PoE+ ports, Onboard DHCP Server, Security Services like Wired/Wireless Firewall, Wireless IDS/IPS,

Onboard AAA Server and IPSEC VPN Gateway, and QoS mechanisms to support Voice & Video , the

RFS4000 transforms the enterprise by delivering a SMART Branch. The RFS4010 RF Switch is the

WLAN’s point of management reducing wireless networking complexity by moving management out

of the ceiling and into the wiring closet. The RFS4010 can adopt upto 6 Adaptive APs or Thin Access

Points and does not require any additional licenses at this time, for AP adoption.

This document is written for the network device installer.

1.1 Package Contents

Inspect the package contents and report any missing or damaged items to your sales representative.

The package should contain the following:

• RFS4010 RF Switch

• Console Cable

•Installation Guide (this document)

• Rubber Feet

• Power Supply Unit (Motorola Part Number: 50-14000-244R)

1.2 Document Conventions

The following graphical alerts are used in this document to indicate notable situations:

NOTE Tips, hints, or special requirements that you should take note of.

CAUTION Care is required. Disregarding a caution can result in data loss or

equipment malfunction.

RFS4010 RF Switch: Installation Guide

1.3 Warnings

•Read all installation instructions and site survey reports, and verify correct equipment installation before connecting

the system to its power source.

•Remove jewelry and watches before installing this equipment.

•Install the equipment in a rack or on a desktop with adequate dimensions and weight allowances.

•Verify the unit is grounded before connecting it to the power source.

•Verify any device connected to this unit is properly wired and grounded.

•Connect all power cords to a properly wired and grounded electrical circuit.

•Verify the electrical circuits have appropriate overload protection.

•Motorola strongly recommends the use of an Uninterruptible Power Supply (UPS) that supports the RFS4010 RF

Switch power rating. Not using a UPS can result in data loss or equipment damage due to a power surge or power

failure.

•Verify that the power connector and socket are accessible at all times during the operation of the equipment.

•Do not work with power circuits in dimly lit spaces.

•Do not install this equipment or work with its power circuits during thunderstorms or other weather conditions that

could cause a power surge.

•Verify there is adequate ventilation around the device, and ambient temperatures meet equipment operation

specifications.

•This product is designed for in building installation only and is not intended to be connected to exposed (outside

plant) networks.

1.4 Site Preparation

•Consult your site survey and network analysis reports to determine specific equipment placement, port capacity,

power drops, and so on.

•Assign installation responsibility to the appropriate personnel.

•Identify where all installed components are located.

•Verify appropriate rack mounting requirements, as required.

•Provide a sufficient number of power drops for your equipment.

•Ensure adequate, dust-free ventilation to all installed equipment.

•Identify and prepare Ethernet and console port connections.

•Verify that cable lengths are within the maximum allowable distances for optimal signal transmission.

•Verify that the RFS4010 RF Switch is powered through an Uninterruptible Power Supply (UPS).

WARNING! Indicates a condition or procedure that could result in personal injury or

equipment damage.

Specifications 3

2 Specifications

2.1 Physical Specifications

2.2 Power Cord Specifications

A power supply is included, however a power cord is not supplied with the switch. Use only a

correctly rated power cord certified (as appropriate) for the country of operation.

2.2.1 Power Protection

•If possible, use a circuit dedicated to data processing equipment. Commercial electrical

contractors are familiar with wiring for data processing equipment and can help with the load

balancing of these circuits.

•Install surge protection. Be sure to use a surge protection device between the electricity

source and the RFS4010 RF Switch.

•Install an Uninterruptible Power Supply (UPS). A UPS provides continuous power during a

power outage. Some UPS devices have integral surge protection. UPS equipment requires

periodic maintenance to ensure reliability. A UPS of the proper capacity for the data processing

equipment must be purchased.

Width 304.8mm (12.0in)

Height 44.45mm (1.75 in) 1 RU

Depth 254mm (10.0 in)

Weight 2.15 Kg (4.75 lbs)

Operating Temperature 0°C - 40°C (32°F - 104°F)

Operating Humidity 5% - 85% RH, non-condensing

Operating Altitude 10,000 ft @ 28deg C < 15% Relative Humidity

RFS4010 RF Switch: Installation Guide

3 LED Codes

The RFS4010 RF Switch has four vertically-stacked LEDs on its front panel. Each of the six Gigabit

Ethernet Ports have two status LEDs. These LEDs display two colors (green & amber), and three lit

states (solid, blinking, and off). The following tables decode the combinations of LED colors and

states for the System Status LEDs and the Gigabit Ethernet LEDs.

3.1 System Status LEDs

SYS

System Status 1

System Status 2

Fan status

Temperature status

LED Codes 5

3.1.1 Start Up / POST (Primary System or Redundant System)

System Status 1 LED System Status 2 LED Event

Off Off Power off

Green Blinking Green Blinking Power On Self Test (POST) running

Green Solid Green Blinking POST succeeded (Operating System Loading)

Green Solid Off POST succeeded (Normal Operation)

Amber Blinking Off POST Failure

Alternating Green Blinking

& Amber Blinking

Alternating Green Blinking

& Amber Blinking System Boot Up Error

NOTE During switch start up, the Temperature status LED will be lit Solid

Amber. This is normal behavior and does not indicate an error. At the

completion of start up the Temperature Status LED will switch to Solid

Green.

RFS4010 RF Switch: Installation Guide

3.1.2 Switch Status (Primary System)

3.1.3 Switch Status (Redundant System)

System Status 1 LED System Status 2 LED Event

Off Off Power off

Green Solid Off

Redundancy Feature Enabled

Primary System Normal Operation

No Access Ports Adopted

Green Solid Green Solid

Redundancy Feature Enabled

Primary System Normal Operation

Actively Adopting Access Ports

Green Solid Amber Blinking

No Country Code configured on the switch

Access Port or Adaptive AP License and Country

Code configured, but no APs adopted

System Status 1 LED System Status 2 LED Event

Off Off Power off

Green Solid Off Redundant System Normal Operation

Green Blinking Green Solid Redundant System failed over and adopting

ports

Green Blinking Alternating Green Blinking

& Amber Blinking Redundant System not failed over.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Motorola Schalten Handbücher

Motorola

Motorola T2-2500 Bedienungsanleitung

Motorola

Motorola RFS Series Bedienungsanleitung

Motorola

Motorola APEX1000 Bedienungsanleitung

Motorola

Motorola WS5100 Series Bedienungsanleitung

Motorola

Motorola RFS Series Bedienungsanleitung

Motorola

Motorola WS2000 - Wireless Switch - Network Management... Bedienungsanleitung

Motorola

Motorola WS2000 - Wireless Switch - Network Management... Bedienungsanleitung

Motorola

Motorola RFS7000GR Bedienungsanleitung

Motorola

Motorola WS2000 - Wireless Switch - Network Management... Bedienungsanleitung

Motorola

Motorola RFS7000 Series Bedienungsanleitung

Motorola

Motorola AP-PSBIAS-1P2-AFR Bedienungsanleitung

Motorola

Motorola WS5100 Series Bedienungsanleitung

Motorola

Motorola RFS7000 Series Bedienungsanleitung

Motorola

Motorola DIMETRA MTS 4 Bedienungsanleitung

Motorola

Motorola M68LC302CAF20VCT Bedienungsanleitung

Motorola

Motorola 549478-001-00 - PowerBroadband EthernetXD M2a WallPlate... Bedienungsanleitung

Motorola

Motorola AP-PSBIAS-1P2-AFR Bedienungsanleitung

Motorola

Motorola RFS6000 - Wireless RF Switch Bedienungsanleitung

Motorola

Motorola RFS7000 Series Bedienungsanleitung

Motorola

Motorola WS5100 Series Bedienungsanleitung

Motorola

Motorola RFS7000 Series Bedienungsanleitung

Motorola

Motorola RFS7000 Series Bedienungsanleitung

Motorola

Motorola M68ICS08JB Bedienungsanleitung

Motorola

Motorola WiNG 4.4 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung

Cisco

Cisco Catalyst X4448 Handbuch