Motorola RFS7000 Series Bedienungsanleitung

RFS7000 Series RF Switch

Installation Guide



MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office.

Symbol is a registered trademark of Symbol Technologies, Inc. All other product or service

1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

2.0 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

3.0 LED Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

4.0 Hardware Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

5.0 Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

6.0 Part Numbers, Support, and Sales . . . . . . . . . . . . . . . . . . . . . 23

7.0 End-User License Agreement . . . . . . . . . . . . . . . . . . . . . . . . . 25

Contents

Introduction 1

1 Introduction

The Motorola RFS7000 Series RF Switch is a high-performance member of Motorola’s Wireless

Switch family. The RFS7000 Series RF Switch provides centralized Wireless LAN (WLAN)

configuration and management by coalescing a network “intelligence” previously spread across

physically distributed access points. By replacing access points with simpler access ports (or “thin”

access points), the RFS7000 Series RF Switch becomes a WLAN’s single point of contact, thus

reducing wireless networking complexity by moving management out of the ceiling and into the

wiring closet. In addition, through the use of patented Virtual AP architecture, the RFS7000 Series

RF Switch lets you create multiple WLANs without changing or adding to the existing wired network

infrastructure.

This document is written for the network device installer.

1.1 Package Contents

Inspect the package contents and report any missing or damaged items to your sales representative.

The package should contain the following:

• RFS7010 RF Switch with Rack Brackets installed

• Console Cable

•Installation Guide (this document)

• China RoHS compliance document

1.2 Document Conventions

The following graphical alerts are used in this document to indicate notable situations:

NOTE Tips, hints, or special requirements that you should take note of.

CAUTION Care is required. Disregarding a caution can result in data loss or

equipment malfunction.

WARNING! Indicates a condition or procedure that could result in personal injury or

equipment damage.

RFS7000 Series RF Switch: Installation Guide

1.3 Warnings

•Read all installation instructions and site survey reports, and verify correct equipment installation before connecting

the system to its power source.

•Remove jewelry and watches before installing this equipment.

•Install the equipment in a rack with adequate dimensions and weight allowances.

•Verify the rack is anchored and cannot tip over or break away from its mountings.

•Verify the unit is grounded before connecting it to the power source.

•Verify any device connected to this unit is properly wired and grounded.

•Connect all power cords to a properly wired and grounded electrical circuit.

•Verify the electrical circuits have appropriate overload protection.

•Attach only approved power cords to the device.

•Motorola strongly recommends the use of an Uninterruptible Power Supply (UPS) that supports the RFS7000 Series

RF Switch power rating. Not using a UPS can result in data loss or equipment damage due to a power surge or power

failure.

•Verify that the power connector and socket are accessible at all times during the operation of the equipment.

•Do not work with power circuits in dimly lit spaces.

•Do not install this equipment or work with its power circuits during thunderstorms or other weather conditions that

could cause a power surge.

•Verify there is adequate ventilation around the device, and ambient temperatures meet equipment operation

specifications.

1.4 Site Preparation

•Consult your site survey and network analysis reports to determine specific equipment placement, port capacity,

power drops, and so on.

•Assign installation responsibility to the appropriate personnel.

•Identify where all installed components are located.

•Verify appropriate rack mounting requirements.

•Provide a sufficient number of power drops for your equipment.

•Ensure adequate, dust-free ventilation to all installed equipment.

•Identify and prepare Ethernet and console port connections.

•Verify that cable lengths are within the maximum allowable distances for optimal signal transmission.

•Verify that the RFS7000 Series RF Switch is powered through an Uninterruptible Power Supply (UPS).

Specifications 3

2 Specifications

2.1 Physical Specifications

2.2 Power Cord Specifications

A power cord is not supplied with the switch. Use only a correctly rated power cord certified (as

appropriate) for the country of operation.

2.2.1 Power Protection

•If possible, use a circuit dedicated to data processing equipment. Commercial electrical

contractors are familiar with wiring for data processing equipment and can help with the load

balancing of these circuits.

•Install surge protection. Be sure to use a surge protection device between the electricity

source and the RFS7000 Series RF Switch.

•Install an Uninterruptible Power Supply (UPS). A UPS provides continuous power during a

power outage. Some UPS devices have integral surge protection. UPS equipment requires

periodic maintenance to ensure reliability. A UPS of the proper capacity for the data processing

equipment must be purchased.

Width 440mm (17.32 in)

Height 44.45mm (1.75 in)

Depth 390.8mm (15.38 in)

Weight 6.12 Kg (13.5 lbs)

Operating Temperature 0°C - 40°C

Operating Humidity 5% - 85% RH, non-condensing

Operating Altitude 3 km (10000 ft)

RFS7000 Series RF Switch: Installation Guide

3 LED Codes

The RFS7010 RF Switch has four vertically-stacked LEDs on its front panel. Each of the switch’s

Gigabit Ethernet ports have two status LEDs. These LEDs display two colors (green & amber), and

three lit states (solid, blinking, and off). The following tables decode the combinations of LED colors

and states for the System Status LEDs and the Gigabit Ethernet LEDs.

3.1 System Status LEDs

3.1.1 Start Up / POST (Primary System or Redundant System)

System Status 1 LED System Status 2 LED Event

Off Off Power off

Green Blinking Green Blinking Power On Self Test (POST) running

Green Solid Green Blinking POST succeeded (Operating System Loading)

Green Solid Off POST succeeded (Normal Operation)

Amber Blinking Off POST Failure

Alternating Green Blinking

& Amber Blinking

Alternating Green Blinking

& Amber Blinking Boot Up Error: Device has an invalid checksum

NOTE During switch start up, the Temperature status LED will be lit Solid

Amber. This is normal behavior and does not indicate an error. At the

completion of start up the Temperature Status LED will switch to Solid

Green.

6\VWHP6WDWXV

)DQVWDWXV

7HPSHUDWXUHVWDWXV

6\VWHP6WDWXV

LED Codes 5

3.1.2 Switch Status (Primary System)

3.1.3 Switch Status (Redundant System)

3.1.4 Fan LED

System Status 1 LED System Status 2 LED Event

Off Off Power off

Green Solid Off No Redundancy Feature Enabled

Green Solid Green Solid Redundancy Feature Enabled

Actively Adopting Access Ports

Green Solid Amber Blinking No License to adopt Access Ports or No Country

Code configured on the switch.

System Status 1 LED System Status 2 LED Event

Off Off Power off

Green Solid Off No Redundancy Feature Enabled

Green Blinking Green Solid Redundant System failed over and adopting

ports

Green Blinking Alternating Green Blinking

& Amber Blinking Redundant System not failed over.

Green Solid Amber Blinking No License to adopt Access Ports or No Country

Code configured on the switch.

Fan LED Event

Off System Off / POST Start

Green Blinking POST in Process

Green Solid All System Fans Normal Operation

Amber Solid Redundant Cooling Failure

System Operational

Amber Blinking

System Cooling Failure

System will be held in reset until the issue is

resolved

RFS7000 Series RF Switch: Installation Guide

3.1.5 Temperature Status LED

Temperature LED Event

Off System Off

Green Solid Ambient Inlet Temperature is within specified

operating limit

Amber Solid

Ambient Inlet Temperature is near the maximum

operating temperature

During switch start up this LED will be lit Solid

Amber. This is normal behavior and does not

indicate an error.

Amber Blinking

Ambient Inlet Temperature is above the

maximum specified operating temperature

System will be held in reset until the issue is

resolved

LED Codes 7

3.2 RJ-45 Gigabit Ethernet LEDs

3.2.1 RJ-45 Port Speed LED

3.2.2 RJ-45 Port Status LED

Port Speed LED Event

Off 10 Mbps

Green Solid 100 Mbps

Green Blinking 1000 Mbps

Amber Blinking Port Fault

Port Status LED Event

Off No Link or Administratively shut down

Green Solid Link present

Green Blinking Activity: Transmit and Receive

Amber Blinking Link Fault

V\PB

3RUW

VSHHG

3RUW

VWDWXV

3RUW

VSHHG

3RUW

VWDWXV

Andere Handbücher für RFS7000 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Motorola Schalten Handbücher

Motorola

Motorola WS5100 Series Bedienungsanleitung

Motorola

Motorola RFS6000 - Wireless RF Switch Bedienungsanleitung

Motorola

Motorola RFS4010 Series Bedienungsanleitung

Motorola

Motorola WS2000 - Wireless Switch - Network Management... Bedienungsanleitung

Motorola

Motorola RFS7000 Series Bedienungsanleitung

Motorola

Motorola WS2000 - Wireless Switch - Network Management... Bedienungsanleitung

Motorola

Motorola WS2000 - Wireless Switch - Network Management... Bedienungsanleitung

Motorola

Motorola RFS7000GR Bedienungsanleitung

Motorola

Motorola RLN5929 Bedienungsanleitung

Motorola

Motorola AP-PSBIAS-1P2-AFR Bedienungsanleitung

Motorola

Motorola EX-3524 Bedienungsanleitung

Motorola

Motorola RFS Series Bedienungsanleitung

Motorola

Motorola RFS6000 - Wireless RF Switch Bedienungsanleitung

Motorola

Motorola APEX1000 Bedienungsanleitung

Motorola

Motorola WS2000 - Wireless Switch - Network Management... Bedienungsanleitung

Motorola

Motorola M68LC302CAF20VCT Bedienungsanleitung

Motorola

Motorola M68ICS08JB Bedienungsanleitung

Motorola

Motorola DIMETRA MTS 4 Bedienungsanleitung

Motorola

Motorola WS5100 Series Bedienungsanleitung

Motorola

Motorola RFS7000 Series Bedienungsanleitung

Motorola

Motorola WiNG 4.4 Bedienungsanleitung

Motorola

Motorola WS5100 Series Bedienungsanleitung

Motorola

Motorola RFS Series Bedienungsanleitung

Motorola

Motorola T2-2500 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung

Cisco

Cisco Catalyst X4448 Handbuch