Moxa Technologies VPort 66-2MP Series Bedienungsanleitung

P/N: 1802000661010

*1802000661010*

VPort 66-2MP Series

Quick Installation Guide

Edition 1.0, September 2015

Technical Support Contact Information

www.moxa.com/support

Moxa Americas:

Toll

-free: 1-888-669-2872

Tel:

1-714-528-6777

Fax:

1-714-528-6778

Moxa China (Shanghai office):

Toll

-free: 800-820-5036

Tel:

+86-21-5258-9955

Fax:

+86-21-5258-5505

Moxa Europe:

Tel:

+49-89-3 70 03 99-0

Fax:

+49-89-3 70 03 99-99

Moxa Asia-Pacific:

Tel:

+886-2-8919-1230

Fax:

+886-2-8919-1231

Moxa India:

Tel:

+91-80-4172-9088

Fax:

+91-80-4132-1045



- 2 -

Overview

The VPort 66-2MP is a vandal-proof, IP66-rated, PTZ speed dome IP

camera for use in harsh, outdoor environments. With a 360° endless PAN,

-6 to 96° TILT, 22X/30X optical/20X digital zoom, H.264/MJPEG triple

video streams, day-and-night camera lens, and -40 to 65°C operating

temperature, the VPort 66-2MP is especially well-suited for outdoor video

surveillance applications.

Package Checklist

Moxa’s VPort 66-2MP is shipped with the following items. If any of these

items is missing or damaged, please contact your customer service

representative for assistance.

•1 × VPort 66-2MP

Model

Lens

Power

Ethernet

VPort 66-2MP-CAM22X f=4.3 mm (wide)

to 94.6 mm (tele),

24 VDC/VAC RJ45

VPort 66-2MP-CAM30X

f=4.3 mm (wide)

to 129.0 mm (tele)

24 VDC/VAC

RJ45

•Screw handle accessory package

Torx screw driver for

attaching/detaching the top

cover.

3.5 mm power jack to 2-pin

terminal block connector for

2-wire power line connection.

Silica gel dry bag (silica gel

desiccant)

for absorbing moisture

inside the camera.

Hook-and-loop fasteners for

attaching the dry bag inside the

camera.

•Quick Installation Guide

•Documentation and software CD (includes user’s manual, Quick

Installation Guide, and utility)

•Warranty card

NOTE

Check the model name on the VPort’s side label to determine if

the model name is correct for your order.

- 3 -

NOTE

This product must be installed in compliance with your local laws

and regulations.

Features

•Maximum 60 FPS @ full HD (1080P, 1920x1080) resolution (only in

single stream mode)

•22X/30X optical and 20X digital zoom (22X: 4.3 to 94.6 mm,

30X: 4.3 to 129 mm)

•Supports MJPEG and H.264 dual codecs

•Supports Full HD/SXGA/WXGA/720P/SVGA/ Full D1/ 4CIF/ VGA/

CIF/QVGA resolution

•TCP, UDP, and HTTP network transmission modes

•Supports QoS (ToS) for transmission priority

•Supports RTSP streaming

•Supports multicast (IGMP) video streaming

•Supports SNMP (V1/V2C/V3) for network system integration and

management

•Accessible IP filtering

•UPnP supported

•Built-in web server for easy configuration

•360° endless pan and -6° to +96° tilt

•Manual max pan speed of 120°/s; Preset max of 255°/s; Alarm

Trigger max of 360°/s*

•Supports PTZ movement calibration

•Minimum illumination up to 0.4 lux (color) and 0.03 lux (B/W)

•Built-in tamper alarm and Video Motion Detection (VMD)

•-40 to 65°C operating temperature

•1 10/100BaseT(X) port with RJ45 connector

•IP66 protection and NEMA Type 4X form factor

•SDXC slot for local event / disconnected recording

•CBR Pro for flexible flow control

•DynaStream™ for network efficiency with dynamic frame rate change

•EN50121-4 compliance

•Supports ONVIF Profile S for multiple video stream profiles

•24 VDC/VAC power input

•Supports NTCIP 1205

•EN 62262 IK10 level vandal resistance

•CE, FCC, UL 60950-1

•Pre, Trigger, and post snapshot images supported

•Sequential snapshot images supported

•Supports SMTP and FTP for alarm message transmission

•Supports HTTP event server

•3-year warranty for product, and 1-year warranty for moving parts**

When the temperature is under -10°C, the maximum PT speed will be

reduced to a max. of 130°/sec.

The following moving parts come with a 1-year warranty:

•

Fan

•

Shutter

•

Zoom lens

•

DC-Iris, P-Iris lens

•

PAN, TILT and lens motors/ mechanism

•Slip ring

- 4 -

VPort 66-2MP Product Description

Appearance

•Top cover screws: Four screws used to secure the top cover.

•Top cover: The top cover can be removed to take out the camera

body for installing or re-installing the SD card.

•Zoom Lens: The VPort 66-2MP-M12 supports 2 lenses with different

optical zoom specs:

22X: f = 4.3 mm (wide) to 94.6 mm (tele), F1.6 to F4.5

30X: f = 4.3 mm (wide) to 129.0 mm (tele), F1.6 to F4.7

•Dome cover: The VPort 66-2MP has a vandal-proof PC dome cover,

satisfying EN 62262 (IEC 62262) class IK10 level.

•Mounting kit: For installing the VPort 66-2MP on a wall or pole. The

mounting kit is not included as a standard accessory with the VPort

66-2MP; it must be ordered and purchased separately. Refer to the

ordering information on the VPort 66-2MP’s datasheet or webpage for

mounting accessory information.

NOTE

The color of the dome cover can be customized based on your

installation environment. Please contact your Moxa sales

representative for information about this customization service.

Note that the color of the dome cover could decrease the light

transmittance of the video image. The darker the dome cover,

the greater the decrease of light transmittance.

Inside the camera

•Camera module: The main body of the VPort 66-2MP.

•Camera module connector: A patented connector for connecting

the camera module with the external connectors with cables.

- 5 -

•SD card socket (SDXC): The VPort 66-2MP supports the SDXC

interface, which can use SD cards with more than 64 GB of memory

for local storage of video recordings (by event or continuous

recording).

NOTE

Since video recording requires a high frequency of read and write

actions

, we recommend using high performance,

high reliability

SD cards, such as Sca

ndisk or Transcend high-end SD cards.

Most important

ly, we highly recommend backing up videos

recorded

on an SD card to a

video recorder, hard disk, or other

more permanent storage media.

External cables and connectors

•Power connector: The VPort 66-2MP supports one 24 VDC or 24

VAC power input, with a 3.5 mm power jack male connector. You can

use a standard 24 VDC/VAC power adapter (3 A min.) to power the

VPort 66-2MP. In addition, a 3.5 mm power jack to 2-pin terminal

block connector is included as a standard VPort 66-2MP accessory for

direct power line connections.

VPort 66-2MP Power Consumption Information

Heater/Fan

Operation

PTZ

Operation

Temp. (inside

the camera)

Power

consumption

Heater/Fan off

Off

0 to 35°C

19 watts

Heater/Fan off

Operating

27 watts

Heater/Fan on

Off

-40 to 0°C

67 watts

Heater/Fan on

Operating

71 watts

Heater off / Fan on

Off

≥35°C

24 watts

Heater off / Fan on

Operating

31 watts

- 6 -

NOTE

•The heater and fan will be enabled when the internal

temperature is under -

10°C, and disabled when above 0°C.

The fan will be enabled when the internal temperature is

above 50°C, and disabled when under 35°C.

•

When using the 3.5 mm power jack to 2-pin terminal block

connector for a direct power line connection, be sure to pay

attention to the “+” and “-“ pin assignments on the

connector.

•

The power input rating of the VPort 66-

2MP is 24 VDC (21.6

to 26.4 VDC) or 24 VAC (21.6 to 26.4 VAC).

•Reset button: For rebooting and restoring factory defaults.

Reboot: Press the button once.

Factory default: Press and hold the button for at least 10

seconds.

•RJ45 Ethernet connector: The RJ45 Ethernet port is for 10/100

Mbps network transmission.

•5-pin terminal block connector for DI/Relay: The VPort 66-2MP

supports 1 DI (digital input) and 1 relay output.

Relay

Output

N.C.

(normal close)

Max. 1 A, 24 VDC

Initial status is

Normal Open

COM (common)

(normal open)

DI DI: I+

High:

+13 V to +30 V

Low:

-30 V to +3 V

GND:

⊥

•4-pin terminal block for audio input/output: The VPort 66-2MP

supports 1 audio input and 1 audio output for an external microphone

and external speaker.

Audio input

IN +

Audio input +

IN -

Audio input -

Audio output

OUT -

Audio output -

OUT +

Audio output +

•Grounding: Attach the grounding cable with attachment ring to the

mounting kit’s grounding screw (inside the mounting kit box) to

ground the VPort 66-2MP.

- 7 -

•Safety Rope: For easier installation, use the safety rope to hook the

camera to the mounting kit buckle.

Hardware Installation

A mounting kit is required to install the VPort 66-2MP. Below we use the

VP-520LB to illustrate; the installation method of other accessories is

similar.

Step 1: Open and remove the top cover.

Use the security torx to loosen the 4 top cover screws.

Step 2: Installing an SD card requires removing the camera

module.

1. Loosen the 2 anti-drop Phillips screws, which hold the camera

module in place.

- 8 -

2. Pull the camera module a little and turn it clockwise to remove the

camera module from the camera module connector.

3. Insert the SD card, and then install the camera module by rotating

the camera module connector counterclockwise. Screw in the 2

anti-drop Phillips screws.

NOTE

If you have difficulty removing the camera module from the

camera module connector,

position the camera module in a

downwards direction. Doing so will make it easier to turn the

camera module clockwise.

Step 3: Install the sunshield (VP-SH1) if required

The VP-SH1 sunshield can be used with the VPort 66-2MP to prevent

direct sunlight from shining on the housing. Using the sunshield could be

warranted since sunlight can affect the heat dissipation mechanism.

Loosen the 4 security screws

on the top of the camera.

- 9 -

2. Remove the black mount kit

and put the VP-SH1 on the

housing. Use the 3 small

Phillips screws in the

VP-SH1’s package to fix the

VP-SH1 to the housing.

3. Replace the black mount kit

tighten the 4 security screws

Step 4: Fasten the dry bag inside the housing

Use the hook-and-loop fastener to attach the dry bag to the camera

housing.

Remove the dry bag from the package stick it

to the hook fastener.

Attach the other side of the hook fastener to

the internal wall of the camera housing. Be

sure not to place

the dry bag on top of the 2

Phillips screws since the dry bag

will block the

way when removing the camera module.

- 10 -

Step 5: Close the top cover and screw in the 4 top cover screws

immediately (5.5 kgf-cm torque is recommended)

NOTE

The dry bag will absorb moisture inside the camera to prevent

oisture from condensing on the inside of the

transparent dome

when

the camera is used in low temperature environments.

Install the dry bag and replace the camera’s top cover

immediately after o

pening the dry bag and exposing it to the

atmosphere.

Step 6: Install the VPort 66-2MP on the VP-520LB mounting kit

1. Loosen the 3 socket set screws on the VP-520LB tube.

2. Loosen the 4 Phillips screws on the front cover, the stud bolts inside

the front cover, and the ground screw inside the box, and then pull

the bolt from the hinge to separate the front cover and the box.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Moxa Technologies Computerhardware Handbücher

Moxa Technologies

Moxa Technologies Smartio CP-104UL Bedienungsanleitung

Moxa Technologies

Moxa Technologies Industrial Serial Board CI-132 Bedienungsanleitung

Moxa Technologies

Moxa Technologies Smartio C104H Bedienungsanleitung

Moxa Technologies

Moxa Technologies CP-602U-I-T Bedienungsanleitung

Moxa Technologies

Moxa Technologies UC-7420-CE Bedienungsanleitung

Moxa Technologies

Moxa Technologies DA-661 Gebrauchsanweisung

Moxa Technologies

Moxa Technologies MiiNePort E1-SDK Bedienungsanleitung

Moxa Technologies

Moxa Technologies RKP-A110 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies WAPN008 Bedienungsanleitung

Moxa Technologies

Moxa Technologies Moxa Smartio C168H Bedienungsanleitung

Moxa Technologies

Moxa Technologies CSM-G200 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies WAPN008-1 Bedienungsanleitung

Moxa Technologies

Moxa Technologies C104P Bedienungsanleitung

Moxa Technologies

Moxa Technologies ABC-02-USB-T Bedienungsanleitung

Moxa Technologies

Moxa Technologies CP-102U/UL Bedienungsanleitung

Moxa Technologies

Moxa Technologies TC-6110 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ioLogik 2500 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies UC-8100 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies CP-118U Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ABC-02-USB Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPort 200A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies CP-102N-T Bedienungsanleitung

Moxa Technologies

Moxa Technologies MPC-2101 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies DA-661 Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung