Moxa Technologies OnCell G3150A-LTE Bedienungsanleitung

P/N: 1802031500022

*1802031500022*

OnCell G3150A-LTE

Quick Installation Guide

Moxa OnCell Series

Edition 2.0, August 2017

Technical Support Contact Information

www.moxa.com/support

Moxa Americas:

Toll

-free: 1-888-669-2872

Tel:

1-714-528-6777

Fax:

1-714-528-6778

Moxa China (Shanghai office):

Toll

-free: 800-820-5036

Tel:

+86-21-5258-9955

Fax:

+86-21-5258-5505

Moxa Europe:

Tel:

+49-89-3 70 03 99-0

Fax:

+49-89-3 70 03 99-99

Moxa Asia-Pacific:

Tel:

+886-2-8919-1230

Fax:

+886-2-8919-1231

Moxa India:

Tel:

+91-80-4172-9088

Fax:

+91-80-4132-1045



- 2 -

Overview

The OnCell G3150A-LTE is a reliable, secure, LTE gateway with

state-of-the-art global LTE module. This 4G cellular gateway provides a

more reliable connection to your Ethernet network for cellular

applications.

To enhance industrial reliability, the OnCell G3150A-LTE features isolated

power inputs, which together with high-level EMS and wide-temperature

support give the OnCell G3150A-LTE the highest level of device stability

for any rugged environment. In addition, with dual-SIM GuaranLink and

dual power inputs, the OnCell G3150A-LTE supports network redundancy

to ensure uninterrupted connectivity.

The OnCell G3150A-LTE also comes with a 3-in-1 serial port for serial over

LTE cellular network communication. Use the OnCell G3150A-LTE to

collect data and exchange data with serial/Ethernet devices.

Package Checklist

Moxa’s OnCell G3150A-LTE is shipped with the following items. If any of

these items is missing or damaged, please contact your customer service

representative for assistance.

•1 OnCell G3150A-LTE unit

•2 2G/3G/4G antennas 2 dBi omni-directional with SMA male

connectors

•1 DIN-rail mounting kit

•Quick installation guide (printed)

•Warranty card

Installation and Configuration

Before installing the OnCell G3150A-LTE, make sure that all items in the

package checklist are in the box. In addition, you will need access to a

notebook computer or PC equipped with an Ethernet port. The OnCell

G3150A-LTE has a default IP address that you must use when connecting

to the device for the first time.

Take the following steps to configure your OnCell G3150A-LTE. Refer to

the Panel Layout of the OnCell G3150A-LTE section below for the location

of the ports and sockets.

Step 1: Insert a SIM card and turn on the OnCell G3150A-LTE

1. Use a screwdriver to loosen the screws and remove the SIM card

cover.

2. Insert one or two 2G/3G/4G SIM cards (full-sized SIM/1FF) into the

SIM card slots located on the bottom of the OnCell G3150A-LTE.

If you are only using one SIM card, insert it in the top slot (slot 1; the

card in slot 1 is referred to as SIM1).

By default, the SIM card in the slot 1 is treated as the primary card.

To change the default to SIM2 (the card in slot 2), log in to the

OnCell’s web UI, and configure SIM2 as the primary card. When the

OnCell device is turned on, it boots up based on the configuration

information stored on the primary SIM card.

3. Turn on the OnCell G3150A-LTE by connecting a power terminal

block to a DC power source (12 to 48 VDC). For details refer to the

Connecting the Power Input section.

4. Reattach the cover.

- 3 -

Step 2: Connect the OnCell G3150A-LTE to a notebook or PC

Since the OnCell G3150A-LTE supports MDI/MDI-X auto-sensing, you can

use either a straight-through cable or crossover cable to connect the

OnCell G3150A-LTE to a computer. See the 10/100BaseT(X) Ethernet

Port Connection section below for detailed instructions. If the LED

indicator on the OnCell G3150A-LTE’s LAN port lights up, it means a

connection has been established.

Step 3: Set up an IP address for the computer

Set an IP address on the same subnet as the OnCell G3150A-LTE. Since

the OnCell G3150A-LTE’s default IP address is 192.168.127.254, and the

subnet mask is 255.255.255.0, you should set the IP address of the

computer to 192.168.127.xxx and subnet mask to 255.255.255.0.

Step 4: Use the web-based manager to configure the OnCell

G3150A-LTE

Open your computer’s web browser and type http://192.168.127.254

in the address field to access the homepage of the web-based

management system. Before the homepage opens, you will need to enter

the username and password. For first-time configuration, enter the

default username and password given below:

Username: admin

Password: moxa

Click on the Login button.

ATTENTION

For security reasons, we strongly recommend changing the

password. To

change the password, select Maintenance



Username/Password

, and then follow the on-screen

instructions.

NOTE

You must either click the Save Configuration or the Restart

button for the configuration changes to take effect.

- 4 -

Panel Layout of the OnCell G3150A-LTE

GPS antenna connector (female SMA)

2. Terminal block (top-down PWR1

and PWR2, 1 digital relay and 2

digital inputs)

3. Grounding screw (M5)

4. 2x2 MIMO antenna ports for LTE

(female SMA)

5. RS-232 serial console (RJ45)

6. 10/100 Base T(X) Ethernet port

(RJ45)

7. LED display

8. DIN-rail mounting kit

9. Reset button

10.

Dual SIM–SIM1

11.

Dual SIM–SIM2

- 5 -

Device Dimensions

DIN-Rail Mounting

DIN-Rail Kit Dimensions

Unit = mm (inch)

The OnCell G3150A-LTE Series computers come with a DIN-rail kit

attached to the back panel. Mount the OnCell G3150A-LTE Series on

corrosion-free mounting rails that meet the EN 60715 standard.

- 6 -

Installation

STEP 1: Insert the upper lip of the DIN rail into the top hook of the

DIN

-rail mounting kit.

STEP 2:

Press the OnCell G3150A-LTE S

eries towards the DIN rail until it

snaps into place.

To remove the OnCell G3150A-LTE from the DIN rail, reverse steps 1 and

2 above.

Wall Mounting (optional)

Wall-Mounting Kit

Dimension

Unit = mm (inch)

For some applications, it may be more convenient to mount the OnCell

G3150A-LTE to a wall, as illustrated below:

STEP 1:

Remove the aluminum

DIN

rail attachment plate

from the OnCell

G3150A

-LTE, and then

attach the wall

-mounting

plates with M3 screws, as

shown in the adjacent

diagram.

- 7 -

STEP 2:

Mounting the OnCell

G3150A-LTE

to a wall requires 4

screws. Use the OnCell

G3150A-LTE

device, with wall

mount plates attached as a guide, to mark the correct

locations of the 4 screws. The heads of the screws

should be less than 6.0 mm in diameter, and the

shafts

should be less than 3.5 mm in diameter, as shown in

the figure at the right.

NOTE

Test the screw head and shank size by inserting the screws into

one of the k

eyhole shaped apertures of the wall-mounting p

lates

before attaching the plates to the wall.

STEP 3:

Once the screws are fixed into the

wall, insert the four screw heads

through the large opening of the

keyhole

-shaped apertures, and

then slide the OnCell

G3150A-LTE

downwards, as indicated in the

accompanying diagram. Tighten

the four screws for added stability.

WARNING

•

This equipment is intended to be used in a Restricted Access

Location, such as a dedicated computer room, where a

ccess

can only be gained by SERVICE PERSONS or by USERS who

have been instructed about the

fact that the metal chassis of

the equipment is extremely hot and may cause burns.

•

Service persons or users should pay special attention and

take special precautions before handling this equipment.

•

Only authorized, well-trained professionals should be allo

wed

to access the restricted access location. Access should be

controlled by the authority responsible for the location with

lock and key or a security identity system.

•

External metal parts are hot!!

Pay special attention or use

special protection before handling this equipment.

Wiring Requirements

WARNING

Safety First!

Be sure to disconnect the power cord before installing and/or

wiring your Moxa OnCell G3150A-LTE.

- 8 -

Read and Follow These Guidelines

•Use separate paths to route wiring for power and devices. If power

wiring and device wiring paths must cross, make sure the wires are

perpendicular at the intersection point.

NOTE

Do not run signal or communications wiring and power wiring in

the same wire conduit. To avoid interference, wires with different

signal characteristics should be routed separately.

•You can use the type of signal transmitted through a wire to

determine which wires should be kept separate. The rule of thumb is

that wiring with similar electrical characteristics can be bundled

together.

•Keep input wiring and output wiring separate.

•It is strongly advised that you label wiring to all devices in the system

when necessary.

ATTENTION

This product is

intended to be supplied by a Listed Power Unit

marked “Class 2” or “LPS” and rated O/P: 9.6 W (12 V/0.78 A to

48 V/0.2 A).

ATTENTION

Make sure

that the external power adapter

(includes power cords

and plug assemblies) provided with the unit is certified and

suitable for use in your country.

Grounding the Moxa OnCell G3150A-LTE

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from the

ground screw to the grounding surface prior to connecting devices. The

minimum cross-sectional area of the grounding conductor should be

equal to that of the input cable.

ATTENTION

his product is intended to be mounted on a well-grounded

mounting surface, such as a metal panel.

The potential difference

between the two ground potentials must be zero. If the potential

difference is NOT zero, the product could be permanently

damaged.

- 9 -

Connecting the Power Input

Pinouts for the Power Inputs and Relay Output

Name

Usage

V1+

DC Power Input 1

V1-

V2+

DC Power Input 2

V2-

Relay Output

Digital Input

COM_1

Digital Input GND

Digital Input

COM_2

Digital Input GND

Wiring the Redundant Power Inputs

The top two pairs of contacts of the 10-contact terminal block connector

located on the top panel of the OnCell G3150A-LTE are used as the two

DC inputs. Top and front views of the terminal block connector are shown

below:

STEP 1: Insert the negative/positive DC wires

into the

V-/V+ terminals.

STEP 2:

To keep the DC wires from pulling

loose,

use a small flat

-blade screwdriver to tight

en the

wire

-clamp screws on the front of the terminal

block connector.

STEP 3:

Insert the plastic terminal block

connector prongs into the terminal block

receptor, which is

located on the

top panel of the

OnCell

G3150A-LTE.

ATTENTION

Before connecting the

OnCell G3150A-LTE to the DC power

inputs, make sure that the DC power source voltage is stable.

Wiring the Relay Contact

The OnCell G3150A-LTE has one relay output, which consists of the two

contacts of the terminal block on the OnCell G3150A-LTE’s top panel.

Refer to the Specifications section for detailed electrical requirement. The

relay contacts are used to indicate user-configured events. The two wires

attached to the relay contacts form an open circuit when a

user-configured event is triggered. If a user-configured event does not

occur, the relay circuit will be closed.

- 10 -

Wiring the Digital Inputs

The OnCell G3150A-LTE has two sets of digital inputs—DI1 and DI2. Each

DI comprises of two contacts on the 6-pin terminal block connector

located on the top panel of the OnCell G3150A-LTE. Refer to the

Specifications section for detailed information on isolated digital input

definition.

Communication Connections

10/100BaseT(X) Ethernet Port Connection

The 10/100BaseT(X) ports located on the front panel of the OnCell

G3150A-LTE are used to connect to Ethernet-enabled devices.

Pinouts for both MDI (NIC-type) ports and MDI-X (HUB/Switch-type)

ports are shown below:

MDI Port Pinouts

MDI-X Port Pinouts

8-pin RJ45

Signal

Tx+

Rx+

Tx-

Rx-

Rx+

Tx+

Rx-

Tx-

Serial DB9 Connection

The OnCell G3150A-LTE has one DB9 male port that supports RS-232,

RS-485-4W, RS-485-2W, and RS-422. The pin assignments are shown in

the table below:

DB9 Male

Connector

RS-232

RS-422/485-4w

RS-485-2w

DCD

TxD-(A)

–

RxD

TxD+(B)

–

TxD

RxD+(B)

Data+(B)

DTR

RxD-(A)

Data-(A)

GND

DSR

–

TRS

–

CTS

–

RS-232 Connection

The OnCell G3150A-LTE has one RS-232 (8-pin RJ45) console port

located on the front panel. Use either an RJ45-to-DB9 or RJ45-to-DB25

cable to connect the Moxa OnCell G3150A-LTE’s console port to your PC’s

COM port. You may then use a console terminal program to access the

OnCell G3150A-LTE for configuring the console configuration.

Inhaltsverzeichnis

Andere Moxa Technologies Tor Handbücher

Moxa Technologies

Moxa Technologies CCG-1500 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies MGate 5102-PBM-PN Bedienungsanleitung

Moxa Technologies

Moxa Technologies MGate 5105-MB-EIP-T Bedienungsanleitung

Moxa Technologies

Moxa Technologies MGate 5102-PBM-PN-T Bedienungsanleitung

Moxa Technologies

Moxa Technologies OnCell Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies SMG-6100 Bedienungsanleitung

Moxa Technologies

Moxa Technologies MGate 5135 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 4511 Handbuch

Moxa Technologies

Moxa Technologies MGate 5101-PBM-MN Bedienungsanleitung

Moxa Technologies

Moxa Technologies MGate 5102-PBM-PN Bedienungsanleitung

Moxa Technologies

Moxa Technologies MGate MB3170 Bedienungsanleitung

Moxa Technologies

Moxa Technologies OnCell G3100 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies AIG-101 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies UC-8580 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies MRC-1002 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies MGate 5119 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies MGate 5122 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies MGate MB3270I Bedienungsanleitung

Moxa Technologies

Moxa Technologies OnCell G3150A-LTE-EU-T Bedienungsanleitung

Moxa Technologies

Moxa Technologies OnCell Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies MGate MB3270 Bedienungsanleitung

Moxa Technologies

Moxa Technologies MGate 5114 Bedienungsanleitung

Moxa Technologies

Moxa Technologies 6110 Bedienungsanleitung

Moxa Technologies

Moxa Technologies UC-8410 Bedienungsanleitung

Beliebte Tor Handbücher anderer Marken

LST

LST M500RFE-AS Bedienungsanleitung

Kinnex

Kinnex Media Gateway Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace 2N StarGate Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung

Telsey

Telsey CPVA 500 - SIP Bedienungsanleitung

RTA

RTA 460A-NNA4 Technisches Datenblatt

Shaw

Shaw Gateway HDPVR Bedienungsanleitung

ABB

ABB VSN900 Kurzanleitung

Commander

Commander Pulse Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Bedienungsanleitung

NETGEAR

NETGEAR C6300BD Bedienungsanleitung

Amit

Amit CDW531AM Bedienungsanleitung

HMS

HMS Netbiter EasyConnect EC150 Bedienungsanleitung

Huawei

Huawei EchoLife HG620 Bedienungsanleitung

AT&T

AT&T U-verse 3801 Gebrauchs- und Pflegehandbuch

Logic IO

Logic IO RTCU MX2 turbo Bedienungsanleitung

Suttle

Suttle MediaMAX MXM-521 Bedienungsanleitung