Moxa Technologies OnCell Series Bedienungsanleitung

P/N: 1802031200010

*1802031200010*

OnCell 3120-LTE-1

Quick Installation Guide

Moxa OnCell Series

Version 1.0, October 2019

Technical Support Contact Information

www.moxa.com/support

Moxa Americas:

Toll

-free: 1-888-669-2872

Tel:

1-714-528-6777

Fax:

1-714-528-6778

Moxa China (Shanghai office):

Toll

-free: 800-820-5036

Tel:

+86-21-5258-9955

Fax:

+86-21-5258-5505

Moxa Europe:

Tel:

+49-89-3 70 03 99-0

Fax:

+49-89-3 70 03 99-99

Moxa Asia-Pacific:

Tel:

+886-2-8919-1230

Fax:

+886-2-8919-1231

Moxa India:

Tel:

+91-80-4172-9088

Fax:

+91-80-4132-1045



- 2 -

Overview

The OnCell 3120-LTE-1 is a reliable, secure, LTE gateway with a state-

of-the-art global LTE module. This 4G cellular gateway provides a more

reliable connection to your Ethernet network for cellular applications.

The OnCell 3120-LTE-1 is ideal for remote-access applications where

power consumption needs to be well managed. The power-saving

functions, which include power scheduling, allow you to manage the

power consumption in your cellular network. Wide-temperature support

coupled with high-level EMS protection give the OnCell 3120-LTE-1 the

highest level of device stability for any rugged environment. In

addition, dual-SIM and GuaranLink support help provide network

redundancy to ensure uninterrupted connectivity.

The OnCell 3120-LTE-1 also comes with a 3-in-1 serial port for serial-

over-LTE cellular network communication, making it suitable for

collecting and exchanging data with serial/Ethernet devices.

Package Checklist

Before installing your OnCell 3120-LTE-1, verify that the package

contains the following items. If any of these items is missing or

damaged, please contact your customer service representative for

assistance.

•1 OnCell 3120-LTE-1 unit

•1 DIN-rail mounting kit

•1 console cable

•Quick installation guide (printed)

•Warranty card

Installation and Configuration

You will need access to a notebook computer or PC equipped with an

Ethernet port. The OnCell 3120-LTE-1 has a default IP address that you

must use when connecting to the device for the first time.

Take the following steps to configure your OnCell 3120-LTE-1. Refer to

the Panel Layout of the OnCell 3120-LTE-1 section below for the

location of the ports and sockets.

- 3 -

Step 1: Insert a SIM card and turn on the OnCell 3120-LTE-1

1. Use a screwdriver to loosen the screws and remove the SIM card

cover located on the top panel of the OnCell 3120-LTE-1.

2. Insert one or two 4G SIM cards (nano SIM) into the SIM card

slot(s).

If you are only using one SIM card, insert it in the top slot (slot 1;

the card in slot 1 is referred to as SIM1).

By default, the SIM card in slot 1 is treated as the primary card.

To change the default to SIM2 (the card in slot 2), log in to the

OnCell’s web UI, and configure SIM2 as the primary card. When

the OnCell device is turned on, it boots up based on the

configuration information stored on the primary SIM card.

3. Turn on the OnCell 3120-LTE-1 by connecting a power terminal

block to a DC power source (9 to 36 VDC). For details, refer to the

Connecting the Power Input section.

4. Reattach the cover.

Step 2: Connect the OnCell 3120-LTE-1 to a notebook or PC

Since the OnCell 3120-LTE-1 supports MDI/MDI-X auto-sensing, you

can use either a straight-through cable or crossover cable to connect

the OnCell 3120-LTE-1 to a computer. See the 10/100BaseT(X)

Ethernet Port Connection section below for detailed instructions. If the

LAN LED indicator on the OnCell 3120-LTE-1 lights up, it means a

connection has been established.

Step 3: Set up an IP address for the computer

Set an IP address on the same subnet as the OnCell 3120-LTE-1. Since

the OnCell 3120-LTE-1’s default IP address is 192.168.127.254, and

the subnet mask is 255.255.255.0, you should set the IP address of

the computer to 192.168.127.xxx and the subnet mask to

255.255.255.0.

Step 4: Use the web-based manager to configure the OnCell

3120-LTE-1

Open your computer’s web browser and type

http://192.168.127.254 in the address field to access the homepage

of the web-based management system. Before the homepage opens,

you will need to enter the username and password. For first-time

configuration, enter the default username and password given below:

Username: admin

Password: moxa

Click on the Login button.

ATTENTION

For security reasons, we strongly recommend changing the

password. To

change the password, select Maintenance



Username/Password

, and then follow the on-screen

instructions.

NOTE

You must click the Save Configuration

and then the

Restart

buttonsfor the configuration changes to take effect.

- 4 -

Panel Layout of the OnCell 3120-LTE-1

1. SIM card holders (SIM1/SIM2)

2. 2x2 MIMO cellular antenna port

3. 10/100 Base-T(X) Ethernet port 1

(RJ45)

4. 10/100 Base-T(X) Ethernet port 2

(RJ45)

5. USB port

6. DB9 serial port

7. LED display

8. Reset button

9. Console port (reserved for

engineering use)

10.

Grounding screw (M3)

11.

Terminal block (V+, V-, GND)

12.

LED display

13.

DIN-rail mounting kit

- 5 -

Device Dimensions

DIN-rail Mounting

The OnCell 3120-LTE-1 Series comes with a DIN-rail kit attached to the

back panel. Mount the OnCell 3120-LTE-1 Series on corrosion-free

mounting rails that meet the EN 60715 standard.

Installation

STEP 1: Insert the upper lip of the DIN rail into the top hook of the

DIN

-rail mounting kit.

STEP 2:

Press the OnCell 3120-LTE-1 Series towards the DIN rail until

it snaps into

place.

- 6 -

To remove the OnCell 3120-LTE-1 from the DIN rail, pull down the

lever at the bottom of the DIN-rail kit.

Wall Mounting (optional)

For some applications, it may be more convenient to mount the OnCell

3120-LTE-1 to a wall, as illustrated below:

STEP 1:

Remove the aluminum

DIN

rail attachment plate

from the OnCell

3120-

LTE

-1, and then attach

the wall

-mounting plates

with M3 screws, as shown

in the adjacent diagram.

STEP 2:

Mounting the OnCell

3120-LTE-1 to a wall requires 4

screws. Use the

OnCell 3120-LTE-1 device, with wall

mount plates attached as a guide, to mark the

correct locations of the 4 screws. The heads of the

screws should be less than 6.0 mm in diameter, and

the

shafts should be less than 3.5 mm in diameter,

as shown in the figure at the right.

NOTE

Test the screw head and shank size by inserting the screws into

one of the k

eyhole shaped apertures of the wall-mounting

plates before attaching the plates to the wall.

STEP 3:

Once the screws are fixed into

the wall, insert

the four screw

heads through the large opening

of the keyhole

-shaped apertures

of the mounting kit

, and then

slide the OnCell

3120-LTE-1

downwards. Tighten the four

screws for added stability.

- 7 -

WARNING

•

This equipment is intended to be used in a Restricted

Access Location, such as a dedicated computer room,

where access can only be gained by SERVICE PERSONS or

by USERS who have been instructed about the fact that the

metal chassis of the equipment is extremely hot and may

cause burns.

•

Service persons or users should pay special attention and

take special precautions before handling this equipment.

•

Only authorized, well-trained professionals should be

allowed to access the restricted access location. Access

should be controlled by the authority responsible for the

location with lock and key or a security identity system.

•

External Metal Parts are Hot!! Pay special attention or

use special protection before handling this equipment.

Wiring Requirements

WARNING

Safety First!

Be sure to disconnect the power cord before installing and/or

wiring the OnCell 3120-LTE-1 device.

Read and Follow These Guidelines

•Use separate paths to route wiring for power and devices. If power

wiring and device wiring paths must cross, make sure the wires are

perpendicular at the intersection point.

NOTE

Do not run signal or communications wiring and power wiring in

the same wire conduit. To avoid interference, wires with

different signal characteristics should be routed separately.

•You can use the type of signal transmitted through a wire to

determine which wires should be kept separate. The rule of thumb

is that wiring with similar electrical characteristics can be bundled

together.

•Keep input wiring and output wiring separate.

•It is strongly advised that you label wiring to all devices in the

system when necessary.

ATTENTION

This product is intended to be supplied by a Listed Power Unit

marked “Class 2” or

“LPS” and rated O/P: 9.6 W (12 V/0.78 A

to 48 V/0.2 A).

- 8 -

Grounding the Moxa OnCell 3120-LTE-1

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from

the ground screw to the grounding surface prior to connecting devices.

The minimum cross-sectional area of the grounding conductor should

be equal to that of the input cable.

ATTENTION

This product is intended to be mounted

on a well-grounded

mount

ing surface, such as a metal panel. The potential

difference between the two ground potentials must be zero. If

the potential difference is NOT zero, the product could be

permanently damaged.

SIM Card Socket

The OnCell 3120-LTE-1 comes with two nano-SIM card sockets for

cellular communication. The nano-SIM card sockets are located on the

top panel along with the antenna connectors. Loosen the screws and

the remove the cover to access the SIM-card sockets, and then insert

the nano-SIM cards into the sockets directly. You will hear a click when

the cards are in place. The left socket is for SIM 1 and the right socket

is for SIM 2. To remove the cards, push the cards in before releasing

them.

Connecting the Power Input

Pinouts for the Power Inputs

Name

Usage

1 V1+

DC Power

Input 1

2 V1-

DC Power

Input 2

GND

Ground

- 9 -

Wiring the Power Input

Top and front views of the terminal block connector are shown below:

STEP 1: Insert the negative/positive DC wires

into the

V-/V+ terminals, and the ground wire

into the G

ND terminal.

STEP 2:

To keep the DC wires from pulling

loose, use a small flat

-blade screwdriver to

tighten the wire

-clamp screws on the front of

the terminal block connector.

STEP 3:

Insert the plastic terminal block

connector prongs into the terminal block

receptor, which is

located on the bottom panel

of the

OnCell 3120-LTE-1.

ATTENTION

Before connecting the

OnCell 3120-LTE-1 to the DC power

inputs, make sure that the DC power source voltage is stable.

Communication Connections

10/100Base-T(X) Ethernet Port Connection

The 10/100Base-T(X) ports located on the front panel of the OnCell

3120-LTE-1 are used to connect to Ethernet-enabled devices.

Pinouts for both MDI (NIC-type) ports and MDI-X (HUB/Switch-type)

ports are shown below:

MDI Port Pinouts

MDI-X Port Pinouts

8-pin RJ45

Signal

Tx+

Rx+

Tx-

Rx-

Rx+

Tx+

Rx-

Tx-

Serial DB9 Connection

The OnCell 3120-LTE-1 has one DB9 male port that supports RS-232,

RS-485-4W, RS-485-2W, and RS-422. The pin assignments are shown

in the table below:

- 10 -

DB9 Male

Connector

RS-232

RS-422/485-4w

RS-485-2w

DCD

TxD-(A)

–

RxD

TxD+(B)

–

TxD

RxD+(B)

Data+(B)

DTR

RxD-(A)

Data-(A)

GND

DSR

–

TRS

–

CTS

–

Console Port

The console port is an RS-232 port that you can connect to with a 4-pin

pin header cable (in the package). You can use this port for debugging

or firmware upgrades.

Signal

GND

RxD

TxD

USB

The OnCell 3120-LTE-1 is provided with a type-A USB 2.0 port, which

can be used to connect USB storage device or other type-A USB

compatible devices.

LED Indicators

LED indicators are provided on the side panel of the OnCell 3120-LTE-1.

The function of each LED is described in the table below:

LED

Color

Behavior

Function

SYS

(2 LEDs)

Green

Power On: System startup is

complete and the system is in

operation.

Off

No power is supplied to the

OnCell device.

Green

1.Blinking at 1-sec

interval

2.Blinking at 2

-sec

intervals

3. Blinking at 0.5

sec intervals

Blinking at 5-

sec

intervals

1. The OnCell device has been

located by the Wireless Search

Utility.

2. The ABC-02-USB device

connected to OnCell device has

been detected.

3. Importing or exporting files

from/to the ABC-02-USB device.

4. The OnCell device is in power

saving mode.

Red

1. Steady On

2. Blinking at

1-sec

intervals

1. System error or failure to get

an IP address for the device.

2. Load/save to the ABC-02-USB

device failed.

LAN 1/2

Green

10/100 Mbps Ethernet mode.

Andere Handbücher für OnCell Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Moxa Technologies Tor Handbücher

Moxa Technologies

Moxa Technologies MGate 5105-MB-EIP Bedienungsanleitung

Moxa Technologies

Moxa Technologies OnCell G3150A-LTE-EU-T Bedienungsanleitung

Moxa Technologies

Moxa Technologies MGate 5105-MB-EIP Bedienungsanleitung

Moxa Technologies

Moxa Technologies MGate MB3180 Bedienungsanleitung

Moxa Technologies

Moxa Technologies MGate-4101-MB-PBS Bedienungsanleitung

Moxa Technologies

Moxa Technologies Mgate MB3660 Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 6110 Bedienungsanleitung

Moxa Technologies

Moxa Technologies OnCell G3150A-LTE Bedienungsanleitung

Moxa Technologies

Moxa Technologies MGate MB3480 Bedienungsanleitung

Moxa Technologies

Moxa Technologies AIG-100 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies MGate MB3180 Bedienungsanleitung

Moxa Technologies

Moxa Technologies MGate MB3280 Bedienungsanleitung

Moxa Technologies

Moxa Technologies MRC Bedienungsanleitung

Moxa Technologies

Moxa Technologies OnCell G3111-HSPA series Bedienungsanleitung

Moxa Technologies

Moxa Technologies MGate 5102-PBM-PN Bedienungsanleitung

Moxa Technologies

Moxa Technologies MGate MB3170 Bedienungsanleitung

Moxa Technologies

Moxa Technologies MGate 5102-PBM-PN Bedienungsanleitung

Moxa Technologies

Moxa Technologies MGate 5102-PBM-PN Bedienungsanleitung

Moxa Technologies

Moxa Technologies 4101I-MB-PBS-T Bedienungsanleitung

Moxa Technologies

Moxa Technologies MGate MB3270I Bedienungsanleitung

Moxa Technologies

Moxa Technologies MGate 5105-MB-EIP Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort Z3150 Bedienungsanleitung

Moxa Technologies

Moxa Technologies MGate MB3000 Modbus Bedienungsanleitung

Moxa Technologies

Moxa Technologies OnCell G3470A-LTE-EU-T Bedienungsanleitung

Beliebte Tor Handbücher anderer Marken

LST

LST M500RFE-AS Bedienungsanleitung

Kinnex

Kinnex Media Gateway Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace 2N StarGate Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung

Telsey

Telsey CPVA 500 - SIP Bedienungsanleitung

RTA

RTA 460A-NNA4 Technisches Datenblatt

Shaw

Shaw Gateway HDPVR Bedienungsanleitung

ABB

ABB VSN900 Kurzanleitung

Commander

Commander Pulse Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Bedienungsanleitung

NETGEAR

NETGEAR C6300BD Bedienungsanleitung

Amit

Amit CDW531AM Bedienungsanleitung

HMS

HMS Netbiter EasyConnect EC150 Bedienungsanleitung

Huawei

Huawei EchoLife HG620 Bedienungsanleitung

AT&T

AT&T U-verse 3801 Gebrauchs- und Pflegehandbuch

Logic IO

Logic IO RTCU MX2 turbo Bedienungsanleitung

Suttle

Suttle MediaMAX MXM-521 Bedienungsanleitung