Moxa Technologies UC-8112-LX STK Bedienungsanleitung

– 1 – – 2 – – 3 –

UC-8112-LX STK Hardware

Quick Installation Guide

First Edition, May 2015

Overview

The UC-8112-LX-STK is a starter kit that contains a UC-8100-LX

embedded computer, a Wi-Fi module, and a cellular module,

offering a complete solution for system evaluation. Users can

easily deploy the UC-8100-LX computer for wireless system

integration and development.

Package Checklist

Before installing the UC-8100, verify that the package contains the

following items:

UC-8112 Computer Kit

•UC-8112-LX computer x 1

•Console cable x 1

•GPS antenna x 1

•Cellular antenna x 1

•Wi-Fi antenna x 1

•DIN rail mounting kit x 1

•1 GB SD x 1

•Power jack x 1

•Power adapter x 1

Wi-Fi Module Kit

•Wi-Fi module x 1

•Wi-Fi antenna cable x 1

Cellular module kit

•Cellular module x 1

•Cellular antenna cable x 1

NOTE: Notify your sales representative if any of the above items

are missing or damaged.

Installing the UC-8100

There are two sliders on the back of the unit for DIN rail and wall

mounting.

Mounting on a DIN-Rail

Pull out the bottom slider, latch the unit onto the DIN-rail, and then

push the slider back in.

Mounting on the Wall

Pull out both the top and bottom

sliders and align the screws

accordingly.

Another method for wall mounting installation is to use the

optional wall mounting kit. Attach two mounting brackets on the

side panel of the computer, and fasten with screws. Install the

computer on a wall or cabinet by fastening two screws for each

bracket.

Connector Description

Power Connector

Connect the “terminal block to power jack converter” (in the

package) to the UC-8100’s DC terminal block (located on the top

panel), and then connect the power adapter. It takes about 30

seconds for the system to boot up. Once the system is ready, the

Ready LED will light up.

Grounding the UC-8100

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI).

SG:

The Shielded Ground (sometimes

called Protected Ground) contact is

the

top contact of the 3-pin power

terminal block connector when

viewed from the angle shown here.

Connect the SG wire to an

appropriate grounded metal surface.

Ethernet Ports

The two 10/100 Mbps Ethernet ports (LAN 1 and LAN 2) use RJ45

connectors.

Signal

ETx+

ETx-

ERx+

ERx-

Serial Ports

The two serial ports (P1 and P2) use terminal connectors. Each

port can be configured by software for RS-232, RS-422, or RS-485.

The pin assignments for the ports are shown in the following table:

RS-232

RS-422

RS-485

TXD

TXD+

---

RXD

TXD-

---

RTS

RXD+

D+

CTS

RXD-

D-

GND

SD/SIM Card Sockets

The UC-8100 comes with an SD socket for storage expansion, and

a SIM card socket for cellular communication. The SD card/SIM

card sockets are located at the lower part on the front panel. To

install them, remove the screw and the protection cover to access

the sockets, and then plug the SD card or the SIM card into the

sockets directly. You will hear “click” when finished. Remember to

push in on the SD card or SIM card first if you want to remove

them.

ATTENTION

By defa

ult, the operating system is stored o

n the SD card.

Do not remove the SD card while the computer is still

running.

– 4 – – 5 – – 6 –

www.moxa.com/support

The Americas:

+1-714-528-6777 (toll-free: 1-888-669-2872)

Europe:

+49-89-3 70 03 99-0

Asia-Pacific:

+886-2-8919-1230

China:

+86-21-5258-9955 (toll-free: 800-820-5036)

Micro SD Card

The UC-8100 comes with a micro SD card socket for storage

expansion. Remove the screws on the side panel, and take off the

cover. Insert the micro SD card into the socket. Make sure you

insert the card in the correct direction.

Console Port

The console port is an RS-232 port that can be connected with a

4-pin pin header cable. You may use this port for debugging or

firmware upgrade. Note that this cable is not included in the

package.

Signal

TxD

RxD

GND

USB

The USB 2.0 port is located in the lower part of the front panel, and

supports a USB storage device driver. The USB storage will be

mounted at /mnt/usbstorage.

Real Time Clock

The UC-8100’s real time clock is powered by a lithium battery. We

strongly recommend that you do not replace the lithium battery

without help from a qualified Moxa support engineer. If you need

to change the battery, contact the Moxa RMA service team.

ATTENTION

There is

a risk

of explosion if the battery is replaced by an

incorrect type of battery.

Cellular Module

The UC-8100 comes with a PCIe socket inside for wireless

communication. Follow these steps:

1. Remove the screws on the side panel, and take off the cover.

2. Find the location of the PCIe socket. Insert the cellular module

into the socket. Fasten the socket with screws.

3. Next you need to install the antenna cable. There are two

antenna connectors on the cellular module. Connect the cable

onto either connector.

4. Install the other end of the cable onto the connector on the

front panel of the UC-8100. Remove the black plastic cover

first.

5. Install the connector, place the locker washer first, and then

insert the nut. Connect the antenna onto the connector.

Wi-Fi Module

1. Use the two silver screws to fasten the stabilization bracket to

the Wi-Fi module. Make sure you connect the bracket in the

correct direction. Insert the Wi-Fi module into the PCIe socket,

and then fasten the bracket in place using the two black

screws.

2. Next you need to install the antenna cable. There are two

antenna connectors on the Wi-Fi module. Connect the cable

onto either connector.

3. Install the other end of the cable onto the connector on the

front panel of the UC-8100. Remove the black plastic cover

first.

4. Install the connector, place the locker washer first, and then

insert the nut. Connect the antenna onto the connector.

Connecting the UC-8100 to a PC

1. Configure the serial console port with the following settings:

Baudrate=115200 bps, Parity=None, Data bits=8, Stop

bits =1, Flow Control=None

ATTENTION

Remember to choose the “VT100” terminal type. Use the

CBL

-RJ45F9-150 cable included in the package

to connect a

PC to the UC-8100’s serial console port.

2. For better network security, we suggest that you download an

SSH program, such as PuTTY, to connect to the UC-8112,

using the following IP address and login information.

Default IP Address

Netmask

LAN 1

192.168.3.127

255.255.255.0

LAN 2

192.168.4.127

255.255.255.0

Password: moxa

Andere Moxa Technologies Industrie-PC Handbücher

Moxa Technologies

Moxa Technologies DA-682C Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies IA3341 Bedienungsanleitung

Moxa Technologies

Moxa Technologies DA-660 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies V460 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies V481-XPE Bedienungsanleitung

Moxa Technologies

Moxa Technologies ThinkCore DA-660-8-CE Bedienungsanleitung

Moxa Technologies

Moxa Technologies UC-8200 Series Gebrauchsanweisung

Moxa Technologies

Moxa Technologies EM-1240-LX Bedienungsanleitung

Moxa Technologies

Moxa Technologies ioLogik E2200 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies W406 WinCE Bedienungsanleitung

Moxa Technologies

Moxa Technologies V2406 Bedienungsanleitung

Moxa Technologies

Moxa Technologies IA241-LX Bedienungsanleitung

Moxa Technologies

Moxa Technologies THINKCORE W345 Bedienungsanleitung

Moxa Technologies

Moxa Technologies V2406-24I Series Gebrauchsanweisung

Moxa Technologies

Moxa Technologies IA240-LX Bedienungsanleitung

Moxa Technologies

Moxa Technologies TC-6110-W7E Bedienungsanleitung

Moxa Technologies

Moxa Technologies DA-685 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies UC-2200A Series Gebrauchsanweisung

Moxa Technologies

Moxa Technologies CN2510 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies DRP-C100 Series Gebrauchsanweisung

Moxa Technologies

Moxa Technologies V2426A-C2 Bedienungsanleitung

Moxa Technologies

Moxa Technologies V481-XPE Bedienungsanleitung

Moxa Technologies

Moxa Technologies UC-8100 Series Gebrauchsanweisung

Moxa Technologies

Moxa Technologies V481-XPE Bedienungsanleitung

Beliebte Industrie-PC Handbücher anderer Marken

Chipsee

Chipsee PPC-A72-101 Bedienungsanleitung

Advantech

Advantech UNO-2184G Bedienungsanleitung

MSI

MSI MS-9A76 Bedienungsanleitung

Stackrack

Stackrack THOR200 Bedienungsanleitung

Nodka

Nodka eBOX-3000-ETC Bedienungsanleitung

Siemens

Siemens SIMATIC IPC627E Bedienungsanleitung

Artila

Artila Matrix-516 Bedienungsanleitung

MSI

MSI MS-9A89 Bedienungsanleitung

Siemens

Siemens SIMATIC Rack PC 840 V2 Bedienungsanleitung

Advantech

Advantech IPPC-6152A Bedienungsanleitung

Beckhoff

Beckhoff CX9020 Bedienungsanleitung

Dell

Dell Embedded Box PC 5000 Bedienungsanleitung

IBASE Technology

IBASE Technology ASB200-918 Series Bedienungsanleitung

Lenovo

Lenovo ThinkCentre M90q Betriebsanleitung

IXXAT

IXXAT Econ 100 Bedienungsanleitung

Kontron

Kontron KBox A-151-TGL Bedienungsanleitung

AXIOMTEK

AXIOMTEK ICO500-518 Series Bedienungsanleitung

JLT

JLT 1214N Bedienungsanleitung