Moxa Technologies NPort W2150A-W4 Series Bedienungsanleitung

P/N: 1802021503052

*1802021503052*

NPort W2150A-W4/

NPort W2250A-W4 Series

Quick Installation Guide

Version 1.1, January 2023

Technical Support Contact Information

www.moxa.com/support



- 2 -

Overview

The NPort W2150A-W4/W2250A-W4 wireless device servers are an

ideal choice for connecting serial devices or Ethernet devices, including

PLCs, meters, and sensors, to an IP-based wireless LAN or Ethernet

LAN.

Features

•Links serial and Ethernet devices to an IEEE 802.11a/b/g/n network

•Web-based configuration using built-in Ethernet or WLAN

•Secure boot for Moxa-only allowed firmware allowed to run

•Remote configuration with HTTPS, SSH

•Secure data access with WEP, WPA, WPA2

•Fast roaming for quick automatic switching between access points

•Offline port buffering and serial data log

•Enhanced surge protection for serial, LAN, and power

•Dual power inputs (1 screw-type power jack, 1 terminal block)

Package Checklist

Before installing the NPort W2150A/W2250A-W4 device server, verify

that the package contains the following items:

•1 NPort W2150A-W4 or NPort W2250A-W4 wireless device server.

•1 antenna 2.4/5GHz: ANT-WDB-ASM-03 BK.

•100 to 240 VAC power adapter. (excluding T models)*

•1 Ethernet cable: CBL-RJ458P-100.

•Quick installation guide (printed).

•Warranty card.

NOTE

The power adapter is suitable for your region.

Optional Accessories

•DK35A (35 mm DIN-rail mounting kit; 4 screws included).

•CBL-PJ21NOPEN-BK-30: Locking barrel plug to bare-wires cable.

•Mini DB9F-to-TB: DB9-female-to-terminal-block adapter for RS-

422/485 applications.

NOTE

Notify your sales representative if any of the above items are

missing or damaged.

ATTENTION

To comply with FCC

RF exposure compliance requirements, the

antenna used for this transmitter must be installed to provide a

separation distance of at least 20 cm from all persons and must

not be co

-located or operating in conjunction with any other

antenna or transmitter.

- 3 -

TTENTION

이

기기는 업무용 환경에서 사용할 목적으로 적합성 평가를 받은 기기로서

가정용

환경에서 사용하는 경우 전파간섭의 우려가 있습니다.

ATTENTION

「取得審驗證明之低功率射頻器材，非經核准，公司、商號或使用者均不

得擅自變更頻率、加大功率或變更原設計之特性及功能。低功率射頻器材

之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即

停用，並改善至無干擾時方得繼續使用。前述合法通信，指依電信管理法

規定作業之無線電通

信。低功率射頻器材須忍受合法通信或工業、科學及

醫療用電波輻射性電機設備之干擾。」

「應避免影響附近雷達系統之操作。」

NOTE

Before connecting the NPort W2150A-W4 and NPort W2250A-

W4 Series DC power inputs, make sure the DC power source

voltage is stable.

•

A qualified person must install the wiring for the input

terminal block.

•

Wire type: Cu.

•

Only use 12 to

28 AWG wire size and a torque value of 0.51

N-m.

NOTE

The operating temperature of the power adapter (included with

the NPort W2150A

-W4/W2250A-W4) is from 0 to 40°C (32 to

104°F). If your application is not i

n this range, please use a

power adapter supplied according to the requirements below:

•

The external power source must comply with UL listed, IEC

60950-1, or IEC/EN 62368-1.

•

Output complies to SELV/ES1, PS2/LPS; output rating 12 to

48 VDC, 0.455 A minimum.

•

A minimum ambient temperature of 55°C or 75°C. (55°C

for the NPort W2150A-W4 and NPort W2250A-W4; 75°

C for

the NPort W2150A-W4-T and NPort W2250A-W4-T)

Hardware Introduction

The NPort W2150A-W4 models have one serial port; the NPort

W2250A-W4 models have two serial ports. Both models support RS-

232/422/485 operation with DB9 connectors and include one 10/100M

Ethernet port.

- 4 -

NPort W2150A-W4

NPort W2150A-W4-T

NPort W2250A-W4

NPort W2250A-W4-T

Reset Button: The reset button is used to load the factory default

settings. Use a pointed object to hold the reset button down for five

seconds to load the factory defaults.

Name

Color

Function

End Panel LED Indicators

Ethernet

Orange

10 Mbps Ethernet connection.

Green

100 Mbps Ethernet connection.

Off

Ethernet cable is disconnected.

Top Panel LED Indicators

Ready

Red

Steady on:

Power is on, and the NPort is booting

up.

Blinking: An IP conflict exists or the DHCP server

did not respond properly.

Green

Steady on:

The NPort is functioning normally.

Blinking:

The NPort is responding to Locate

function.

Off

Power is off or a power error condition exists.

WLAN Green

Steady on:

Wireless enabled.

Blinking:

The NPort can’t establish a WLAN

connection with the AP (Infrastructure).

Off

Wireless not enabled.

Serial 1

Serial 2

Orange

The serial port is receiving data.

Green

The serial port is transmitting data.

Off

No data is flowing to or from the serial port.

- 5 -

Name

Color

Function

Signal

Strength

Red

1 Red - The signal strength (RSSI) is lower than

-88 dBm.

2 Red -

The signal strength (RSSI) is between

-87 to -79 dBm.

Green

3 Green -

The signal strength (RSSI) is between

-78 to -68 dBm.

4 Green - The signal strength (RSSI) is between

-67 to -60 dBm.

5 Green -

The signal strength (RSSI) is between

-59 to -45 dBm.

Pull-high/low Resistors and Termination Resistor

for RS-422/485

You may need to set the pull

high/low resistors when

the

termination

resistors are used in

certain RS

-422 or RS-485

environments.

S4 (Serial 1)

S5 (Serial 2)

DIP 1

DIP 2

DIP 3

DIP 4

Pull-high

Resistor

Pull-low

Resistor

Termination

Resistor

Reserved

1 kΩ

120 Ω

–

OFF (Default)

150 kΩ

N/A

–

S5 is for the NPort W2250A-W4 only.

NOTE

Do not use the 1 k

Ωsetting while in RS-232 mode. Doing so

will degrade the RS

-232 signals and reduce the effective

communication distance.

- 6 -

First-Time Hardware Installation

STEP 1:

After removing the NPort W2150A-W4/W2250A-W4 from the

box, use a crossover Ethernet cable t

o connect the NPort’s

RJ45 Ethernet port directly to your comput

er’s Ethernet port.

STEP 2:

Attach the power adapter to the NPort and then plug the

adapter into an electrical outlet.

STEP 3:

Configure the NPort W2150A-W4/W2250A-W4 through the

Etherne

t port. See the next section on how to install

software.

NOTE

You

must connect the Ethernet cable first before powering up

your NPort.

Wall Mounting (Optional)

Mounting the NPort W2x50A-W4 Series on the wall requires 2 screws.

The heads of the screws should follow the specification of the M3 pitch

0.5 screws with a minimum length > 7mm.

NOTE

Do not screw the screws in all the way—leave about 2 mm to

allow room for sliding the

wall mount panel between the wall

and the screws.

DIN-rail Mounting (Optional)

DIN-rail attachments can be purchased separately to attach the NPort

W2x50A-W4 Series to a DIN rail. When snapping the attachments to

the DIN rail, make sure that the stiff metal springs are at the top.

- 7 -

Software Installation

For the NPort’s configuration, the default IP address of the NPort is:

LAN: Static; IP = 192.168.126.254; netmask = 255.255.255.0

WLAN: Static; IP = 192.168.127.254; netmask = 255.255.255.0

If the NPort is configured for DHCP, but the DHCP server cannot be

found, then the NPort will use the factory default IP settings.

NOTE

If you have forgotten the NPort's IP address, use the Device

Search Utility

(DSU) from your PC to locate the NPort. After

sear

ching the LAN for NPort units, the DSU will display the IP

address of each unit.

NOTE

Ethernet Bridge Disabled (default): Only one network

interface

can be activated at a time. If the Ethernet link is

active, the WLAN will be inactive. If the WLAN is active, the

Ethernet link will be inactive.

Ethernet Bridge Enabled:

The LAN and WLAN will both be

active. Go to the web console, find the network setting

s page,

and set Ethernet Bridge to Enabled.

You may log in with the account name admin and password moxa to

change any settings to meet your network topology (e.g., IP address)

or serial device (e.g., serial parameters). For first-time use, click the

Wizard in the left navigation panel. The wizard will prompt you to

configure the IP address, SSID, and security mode. For other settings,

use the factory defaults or change the settings for your application.

For software installation, download the relative utilities from Moxa's

website:

https://www.moxa.com/support/support_home?isSearchShow=1

•Download the NPort Windows Driver Manager and install it as the

driver to run with Real COM mode of the NPort Series.

•Execute NPort Windows Driver Manager; then map the virtual COM

ports on your Windows platform.

•You may refer to the DB9 Male pin assignment section to loop back

pin 2 and pin 3 for the RS-232 interface to carry out a self-test on

the device.

•Use HyperTerminal or a similar program (you may download Moxa's

program, called PComm Lite) to test whether the device is good or

not.

- 8 -

Pin Assignments and Cable Wiring

Pin RS-232

RS-422,

4w RS-485

2w RS-485

DCD

TxD-(A)

–

RXD

TxD+(B)

–

TXD

RxD+(B)

Data+(B)

DTR

RxD-(A)

Data-(A)

GND

DSR

–

RTS

–

CTS

–

Specifications

Power Requirements

Power Input

12 to 48 VDC

Input Rating

1-port: 12 to 48 VDC, max 429 mA @ 12 VDC

2-port: 12 to 48 VDC, max 455 mA @ 12 VDC

Power Connector Screw-type power jack or terminal block (only one

connection at a time)

Physical Characteristics

Material

Aluminum sheet metal (1 mm)

Dimensions 77 × 111 × 26 mm (no ears, no antenna)

100 × 111 × 26 mm (with ears, no antenna)

Antenna Length

108 mm

Magnetic Isolation

1.5 kV magnetic isolation built in

Environmental Limits

Operating

Temperature

Standard Models:

0 to 55°C (32 to 131°F), 5 to 95%RH

Wide Temp. Models:

-40 to 75°C (-40 to 167°F), 5 to 95%RH

Storage

Temperature

-40 to 85°C (-40 to 185°F), 5 to 95%RH

Andere Handbücher für NPort W2150A-W4 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Moxa Technologies Server Handbücher

Moxa Technologies

Moxa Technologies NPort 5210A Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort W2250A-T-EU Bedienungsanleitung

Moxa Technologies

Moxa Technologies CN2600 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5200 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice Handbuch

Moxa Technologies

Moxa Technologies NPort IA5250I/5250I-T Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort W2250A Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 2310 Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPORT 6600 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 6150 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5600-8-DT Bedienungsanleitung

Moxa Technologies

Moxa Technologies 6150 Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort P5250A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort DE-311 Bedienungsanleitung

Moxa Technologies

Moxa Technologies CN2500 Bedienungsanleitung

Moxa Technologies

Moxa Technologies CN2510-8 Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5150AI-M12 Bedienungsanleitung

Moxa Technologies

Moxa Technologies 5400 Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort W2150A Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5110 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5600-8-DTL Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies CN2610 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies CN2510 Series Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung

Planet

Planet NAS-7410 Bedienungsanleitung

Lenovo

Lenovo ThinkSystem SR635 V3 Bedienungsanleitung