Moxa Technologies EDS-G205-1GTXSFP Handbuch

P/N: 1802002051030

EDS-G205-1GTXSFP

Hardware Installation Guide

Moxa EtherDevice Switch

First Edition, April 2015

- 2 -

Overview

The EDS-G205-1GTXSFP switches are equipped with 5 Gigabit Ethernet

ports (4 10/100/1000BaseT(X) ports and 1 combo 10/100/1000BaseT(X)

or 100/1000BaseSFP port), making them ideal, economical solutions for

demanding, high bandwidth Gigabit Ethernet applications. In addition,

the built-in relay warning function alerts system administrators when

power failures or port breaks occur, and the add-on 4-pin DIP switches

can be used to configure broadcast storm protection, jumbo frame rate,

IEEE 802.3az energy saving, and 100/1000 SFP speed switching. The

EDS-G205-1GTXSFP series includes 2 models: one with an operating

temperature range of -10 to 60°C, and the other with an extended

operating temperature range of -40 to 75°C. These 2 models have passed

a 100% burn-in test to ensure that they fulfill the special needs of

industrial automation control. The EDS-G205-1GTXSFP series can be

easily installed on a DIN rail or in distribution boxes.

Package Checklist

The EDS-G205-1GTXSFP is shipped with the following items.

•Moxa EDS-G205-1GTXSFP Switch

•Hardware installation guide

•Warranty card

Note: Please contact your customer service representative for assistance

if any of these items are missing or damaged.

Features

High Performance Network Switching Technology

•10/100/1000BaseT(X) (RJ45), auto negotiation speed, F/H duplex

mode

•IEEE 802.3/802.3u/802.3ab/802.3z

•100BaseSFP/1000BaseSFP; easily configure speed by DIP switch

•Store and Forward switching process type, 8K MAC address entries.

Industrial Grade Reliability and Efficiency

•Power failure, port break alarm by relay output

•Redundant dual 12/24/48 VDC power inputs

•IEEE 802.3az energy-efficient Ethernet settings by DIP switch

•Jumbo frame setting by DIP switch

Rugged Design

•Operating temperature range of -10 to 60°C, or extended operating

temperature of -40 to 75°C for T models

•IP30, rugged high-strength housing

•DIN rail or panel mounting capability

- 3 -

Panel Layout of the EDS-G205-1GTXSFP

1. Terminal block for power input

(PWR1, PWR2) and relay output

2. PWR1: LED for power input 1

3. PWR2: LED for power input 2

4. FAULT: LED indicator

5. 10/100/1000BaseT(X) LED

indicator (Amber: 10/100M;

Green: 1000M)

6. Port number

7. 2 to 5: 10/100/1000 BaseT(X)

ports

8. 1: 10/100/1000 BaseT(X) or

100/1000Base SFP slot combo

port

9. Model Name

10.

Grounding screw

11.

DIP switches

12.

Screw hole for wall mounting kit

13.

DIN rail kit

- 4 -

Mounting Dimensions, unit = mm (inch)

- 5 -

DIN Rail Mounting

The aluminum DIN rail attachment plate should already be fixed to the

back panel of the switch when you take it out of the box. If you need to

reattach the DIN rail attachment plate, make sure the stiff metal spring is

situated towards the top, as shown in the figures below.

STEP 1:

Insert the top of the DIN

rail into

the slot just

below the stiff metal

spring.

STEP 2:

The DIN

rail attachment unit will

snap into place as shown below.

To remove the DIN rail from the switch, simply reverse Steps 1 and 2.

Wall Mounting (optional)

For some applications, you will find it convenient to mount the switch on

the wall, as illustrated below.

STEP 1:

Remove the aluminum DIN

rail attachment plate from

the

switch’s

rear panel, and

then attach the wall mount

plates, as shown in the

igure.

STEP 2:

Mounting

the switch

on the wall requires 4 screws. Use

the

witch, with wall mount plates attached, as a guide

to mark the correct locations of the 4 s

crews. The

heads of the screws should be less than 6.0 mm in

diameter, and the shafts should be less than 3.5

mm in

diameter, as shown in the figure at the right.

NOTE

Before tightening the screws into the wall, make sure the screw

head and shank size are suitable by inserting the screw into one

of the keyhole-shaped apertures of the wall mounting plates.

Do not screw the screws in all the way—leave about 2 mm to allow room

for sliding the wall mount panel between the wall and the screws.

- 6 -

STEP 3:

Once the screws are fixed in

the wall, insert the four screw

heads through the large parts

of the keyhole

-shaped

apertures, and then slide the

switch

downwards, as

indicated

. Tighten the four

screws for

added stability.

Wiring Requirements

WARNING

Safety First!

Turn

the power off before disconnecting modules or wires. The

proper

power supply voltage is listed on the product label. Check

the voltage of your power source to make sure you are using the

correct voltage. Do NOT use a voltage greater than

what is

specified on the product label.

These devices must be supplied by a

AELV source as defined in

the Low Voltage Directive 2006/95/EC and 2004/108/EC.

WARNING

Safety First!

Calculate the maximum possible current in each power wire and

common wire.

Observe all electrical codes dictating the

maximum current allowable for each wire size.

If the current goes above the maximum ratings, the wiring could

overheat, causing serious damage to your equipment.

You should also pay attention to the following items:

•Use separate paths to route wiring for power and devices. If power

wiring and device wiring paths must cross, make sure the wires are

perpendicular at the intersection point.

NOTE: Do not run signal or communications wiring and power wiring

in the same wire conduit. To avoid interference, wires with different

signal characteristics should be routed separately.

•You can use the type of signal transmitted through a wire to

determine which wires should be kept separate. The rule of thumb is

that wiring with similar electrical characteristics can be bundled

together.

•Keep input wiring and output wiring separated.

- 7 -

•We strongly advise labeling the wiring for all devices in the system.

Grounding Your Moxa Switch

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from the

ground screw to the grounding surface prior to connecting devices.

ATTENTION

This produ

ct is intended to be mounted to a well-grounded

mounting surface, such as a metal panel.

Wiring the Alarm Contact

The alarm contact consists of the two middle contacts of the terminal

block on the switch’s top panel. You may refer to the next section for

detailed instructions on how to connect the wires to the terminal block

connector, and how to attach the terminal block connector to the terminal

block receptor.

In this section, we explain the meaning of the two contacts used to

connect the alarm contact.

FAULT: The two middle contacts of the

-contact terminal block connector

are used to

detect both power faults and port faults. The

two wires attached to the Fault contacts form

n open circuit when:

1. The switch has lost power from one of the

DC power inputs.

2. The PORT ALARM DIP switch for one of

the ports is set to ON, but the port is not

connected properly.

neither of these two conditions is satisfied,

the Fault circuit will

be closed.

Wiring the Redundant Power Inputs

The top two contacts and the bottom two contacts of the 6-contact

terminal block connector on the switch’s top panel are used for DC inputs.

Top and front views of one of the terminal block connectors are shown

here.

- 8 -

STEP 1: Insert the negative/positive DC

wires into the

V-/V+ terminals.

STEP 2:

To keep the DC wires from pulling

loose, use a small flat

blade screwdriver to

tighten the wire

clamp screws on the front

of the terminal block connector.

STEP

3: Insert the plastic terminal block

connector prongs into the terminal block

receptor, which is

located on switch’s top

panel.

ATTENTION

Before connecting

the switch

to the DC power inputs, make sure

the DC power source voltage is stable.

Communication Connections

EDS-G205-1GTXSFP switches have 2 types of communication port:

•4 10/100/1000BaseT(X) Ethernet ports

•1 combination 10/100/1000T(X) or 100/1000BaseSFP port

10/100/1000BaseT(X) Ethernet Port Connection

The 10/100/1000BaseT(X) ports located on switch’s front panel are used

to connect to Ethernet-enabled devices. Most users will choose to

configure these ports for Auto MDI/MDI-X mode, in which case the port’s

pinouts are adjusted automatically depending on the type of Ethernet

cable used (straight-through or cross-over), and the type of device

(NIC-type or HUB/Switch-type) connected to the port.

In what follows, we give pinouts for both MDI (NIC-type) ports and MDI-X

(HUB/Switch-type) ports. We also give cable wiring diagrams for

straight-through and cross-over Ethernet cables.

10/100BaseT(x) RJ45 Pinouts

MDI Port Pinouts

MDI-X Port Pinouts

8-pin RJ45

Signal

Tx+

Tx-

Rx+

Rx-

Signal

Rx+

Rx-

Tx+

Tx-

- 9 -

1000BaseT RJ45 Pinouts

MDI

MDI-X

BI_DA+

BI_DB+

BI_DA-

BI_DB-

BI_DB+

BI_DA+

BI_DC+

BI_DD+

BI_DC-

BI_DD-

BI_DB-

BI_DA-

BI_DD+

BI_DC+

BI_DD-

BI_DC-

RJ45 (8-pin) to RJ45 (8-pin) Straight-Through Cable Wiring

RJ45 (8-pin) to RJ45 (8-pin) Cross-Over Cable Wiring

100/1000BaseSFP (mini-GBIC) Fiber Port

One of the Gigabit Ethernet ports on the EDS-G205-1GTXSFP is an SFP

slot, which requires 100M or 1G mini-GBIC fiber transceivers to work

properly. Moxa provides complete transceiver models for various distance

requirements.

The concept behind the LC port and cable is straightforward. Suppose you

are connecting devices I and II. Unlike electrical signals, optical signals do

not require a circuit in order to transmit data. Consequently, one of the

optical lines is used to transmit data from device I to device II, and the

other optical line is used to transmit data from device II to device I, for

full-duplex transmission.

Remember to connect the Tx (transmit) port of device I to the Rx (receive)

port of device II, and the Rx (receive) port of device I to the Tx (transmit)

port of device II. If you make your own cable, we suggest labeling the two

- 10 -

sides of the same line with the same letter (A-to-A and B-to-B, as shown

below, or A1-to-A2 and B1-to-B2).

LC-Port Pinouts

LC-Port to LC-Port Cable Wiring

ATTENTION

This is a Class 1 Laser/LED product. To avoid causing serious

damage to your eyes, do not stare directly into the laser beam.

Redundant Power Inputs

Both power inputs can be connected simultaneously to live DC power

sources. If one power source fails, the other live source acts as a backup,

and automatically supplies all of the switch’s power needs.

Alarm Contact

The EDS-G205-1GTXSFP has one alarm contact located on the top panel.

For detailed instructions on how to connect the alarm contact power wires

to the two middle contacts of the 6-contact terminal block connector, see

the Wiring the Alarm Contact section on page 7. A typical scenario

would be to connect the Fault circuit to a warning light located in the

control room. The light can be set up to switch on when a fault is detected.

The alarm contact has two terminals that form a Fault circuit for

connecting to an alarm system. The two wires attached to the Fault

contacts form an open circuit when (1) the switch has lost power from one

of the DC power inputs, or (2) one of the ports, for which the

corresponding PORT ALARM DIP switch is set to ON, is not properly

connected.

If neither of these two conditions occurs, the Fault circuit will be closed.

DIP Switch Settings

The default setting for each DIP switch is OFF.

The following table explains the effect of setting

the DIP switches to the ON positions.

Inhaltsverzeichnis

Andere Moxa Technologies Schalten Handbücher

Moxa Technologies

Moxa Technologies PT-7324 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDS-510E Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ToughNet Switch TN-5500 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies PowerTransPT-7528 Series Handbuch

Moxa Technologies

Moxa Technologies PT-7528 Handbuch

Moxa Technologies

Moxa Technologies TN-5516A Series Handbuch

Moxa Technologies

Moxa Technologies ETHERDEVICE EDS-305 Handbuch

Moxa Technologies

Moxa Technologies EtherDevice EDS-P206A-4PoE Series Handbuch

Moxa Technologies

Moxa Technologies EtherDevice EDS-G205A-4POE-1GSFP-T Bedienungsanleitung

Moxa Technologies

Moxa Technologies ThinkCore DA-660-8-CE Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDS-2016-ML Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ToughNet TN-5524-8PoE Handbuch

Moxa Technologies

Moxa Technologies UPort 400A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies PowerTrans PT-7528-24TX-WV Bedienungsanleitung

Moxa Technologies

Moxa Technologies PowerTrans PT-7728-PTP Handbuch

Moxa Technologies

Moxa Technologies EDS-G2008-EL Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDS-205 Bedienungsanleitung

Moxa Technologies

Moxa Technologies ToughNet TN-5510-2GLSX-ODC Handbuch

Moxa Technologies

Moxa Technologies EDS-316 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort S8000 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies IEX-408E-2VDSL2-HV Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDS-G509-T Handbuch

Moxa Technologies

Moxa Technologies NSwitch Outdoors Bedienungsanleitung

Moxa Technologies

Moxa Technologies TN-5508A Series Handbuch

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung

Cisco

Cisco Catalyst X4448 Handbuch