Moxa Technologies IKS-6728-8PoE Handbuch

P/N: 1802067280022

IKS-6728-8PoE

Hardware Installation Guide

Third Edition, October 2013

- 2 -

Package Checklist

The Moxa IKS-6728-8PoE industrial rackmount switch is shipped with the

following items. If any of these items are missing or damaged, please

contact your customer service representative for assistance.

•IKS-6728-8PoE switch

•USB cable (Type A male to Type B male)

•Protective caps for unused ports

•2 rackmount ears

•Documentation and software CD

•Hardware installation guide

•CD-ROM with user's manual and SNMP MIB file

•Moxa product warranty statement

Panel Layouts

1. System status LEDs

2. Model name

3. Reset button

4. Terminal block for relay output

5. USB serial console port

6. USB storage port (ABC-02-USB-T)

7. 10/100/1000BaseT(X) or 100/1000Base SFP combo ports

8. 100/1000Base SFP port status LEDs

9. PoE+ status LEDs

10. 10/100BaseT(X) port status LEDs

11. Fast Ethernet or PoE+ interface ports

12. Fast Ethernet or PoE+ interface modules

13. Terminal blocks for DC power inputs

14. Grounding screw

15. Power sockets for AC power inputs

- 3 -

Dimensions

Unit = mm (inch)

Fast Ethernet Interface Modules (IM-6700 Series)

- 4 -

Grounding the Moxa Industrial Rackmount Switch

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from the

ground screw to the grounding surface prior to connecting devices.

NOTE

Using a shielded cable achieves better electromagnetic

compatibility.

Connecting the Power Inputs

The IKS-6728-8PoE switches support 4 types of power supply.

•IKS-6728-8PoE-4GTXSFP-HV-HV-T: Two isolated 110/220 VAC (85

to 264 VAC) power supplies for switch and two isolated 48 VDC power

inputs for PoE+ ports

•IKS-6728-8PoE-4GTXSFP-HV-T: One isolated 110/220 VAC (85 to

264 VAC) power supply for the switch and one isolated 48 VDC power

input for the PoE+ ports

•IKS-6728-8PoE-4GTXSFP-48-48-T: Two isolated 48 VDC power

supplies for switch and PoE+ ports

•IKS-6728-8PoE-4GTXSFP-48-T: One isolated 48 VDC power supply

for switch and PoE+ ports

For the HV models, the 110/220 VAC power supplies provide power for

switch operation. Separate 48 VDC power supplies are required to provide

power to all PoE+ ports (50 to 57 VDC is recommended for IEEE 802.3at

devices).

For the 48 VDC models, the 48 VDC power supplies provide power for

switch operation and to all PoE+ ports (50 to 57 VDC is recommended for

IEEE 802.3at devices).

Wiring Requirements

WARNING

Do not disconnect modules or wires unless power has been

switched off or the area is known to be non

-hazardous. The

device may only be connected to the supply voltage shown on the

type plate. The

device is designed for operation with a Safety

Extra

-Low Voltage (SELV) or an isolated power supply, which

means that they may only be connected to the supply voltage

connections and to the signal contact with a SELV or an isolated

power supply in complian

ce with IEC 60950-1/EN 60950-

1 or UL

508.

AC Power Inlets

The connection for PWR1 (power supply 1) and PWR2 (power supply 2)

are located on the rear panel (shown below). Be sure to use a standard

power cord with an IEC C13 connector, which is compatible with the AC

power inlet.

- 5 -

DC Power Terminal Blocks

The connection for EPS1 (external power supply 1) / PWR1 (power supply

1) and EPS2 (external power supply 2) / PWR2 (power supply 2) are

located on the rear panel (shown below).

STEP 1: Insert the negative/positive DC wires into the V-/V+ terminals,

respectively.

STEP 2: To keep the DC wires from pulling loose, use a screwdriver to

tighten the wire-clamp screws.

Wiring the Relay Contact

Each IKS-6728-8PoE switch has one relay output.

FAULT:

The relay contact of the 2-pin terminal block connector is used to detect

user-configured events. The two wires attached to the fault contacts form

an open circuit when a user-configured event is triggered. If a

user-configured event does not occur, the fault circuit remains closed.

USB Connection

The IKS-6728-8PoE switch has two USB ports, one type B USB-serial

console port and one type A USB host port, located on the front panel. Use

a USB cable (type A male to type B male) to connect the USB-serial

console port to your PC's COM port, and install the UPort 1110 driver to

verify operation. You may then use a console terminal program, such as

Moxa’s PComm Terminal Emulator, to access the IKS-6728-8PoE's

console configuration utility.

Use Moxa’s USB Automatic Backup Configurator ABC-02-USB-T to

connect to the USB host port to backup and restore configuration files,

auto-load configuration files, upgrade firmware, and backup system log

files.

- 6 -

The Reset Button

Depress the Reset button for five continuous seconds to load the factory

default settings. Use a pointed object, such as a straightened paper clip or

toothpick, to depress the Reset button. When you do so, the STATE LED

will start to blink about once per second. Continue to depress the STATE

LED until it begins blinking more rapidly; this indicates that the button has

been depressed for five seconds and you can release the Reset button to

load factory default settings.

NOTE

DO NOT power off the switch when loading default settings

LED Indicators

The front panel of the IKS switch contains several LED indicators. The

function of each LED is described in the table below.

LED

Color

State

Description

System LEDs

PWR1* AMBER

Power is being supplied to the main

module’s power input PWR1

Off

Power is not being supplied to the

main module’s power input PWR1

PWR2* AMBER

On Power is being supplied to the main

module’s power input PWR2

Off

Power is not being supplied to the

main module’s power input PWR2

EPS1 AMBER

Power is being supplied to the PoE+

power input EPS1

Off Power is not being supplied to the

PoE+ power input EPS1

EPS2 AMBER

Power is being supplied to the PoE+

power input EPS2

Off

Power is not being supplied to the

PoE+ power input EPS2

*: On the IKS-6728-8PoE-4GTXSFP-48-48-T model, both PWR1 and

PWR2 LED will be “On” with a single power input. This is because both

internal power units are operating as redundant secondary power with

the single input.

STATE

GREEN

On System has passed self-diagnosis test

on boot-up and is ready to run

Blinking

1. System is undergoing the

self-diagnosis test

2. Blink continuously when pressing

the reset button 5 seconds to reset to

factory default

3. Blink slowly when an ABC-02

automatic backup device is detected

RED On

System failed self-diagnosis on

boot-up

- 7 -

LED

Color

State

Description

FAULT RED On

System is in the event of failure, or is

under quick inspection

Off

System is in normal operation

MSTR/

HEAD GREEN

When the IKS-6728-8PoE is set as the

Master of the Turbo Ring, or as the

Head of the Turbo Chain

Blinking

The IKS-6728-8PoE has become the

Ring Master of the Turbo Ring, or the

Head of the Turbo Chain, after the

Turbo Ring or the Turbo Chain is down

Off

The IKS-6728-8PoE is not the Master

of this Turbo Ring or is set as a

Member of the Turbo Chain

CPLR/

TAIL GREEN

When the IKS-6728-8PoE coupling

function is enabled to form a back-

path, or when it’s set as the Tail of the

Turbo Chain

Blinking

When the Turbo Chain is down

Off When this IKS-6728-8PoE switch

disables the coupling function

When the system is importing/exporting data from or to an ABC-02

automatic backup device, the FAULT, MSTR/HEAD, and CPLR/TAIL LEDs

will blink in sequence.

Port Status LEDs

G1 to G4

(1000M TP

ports, left

LED on the

connector)

GREEN

On The corresponding port’s 1000 Mbps

link is active

Blinking

Data is being transmitted at 1000

Mbps

Off

The corresponding port’s 1000 Mbps

link is inactive

G1 to G4

(10/100M TP

ports, right

LED on the

connector)

GREEN

The corresponding port’s 10/100

Mbps link is active

Blinking Data is being transmitted at 10/100

Mbps

Off

The corresponding port’s 10/100

Mbps link is inactive

G1 to G4

(100/1000M

Fiber Optic

ports)

GREEN

Fiber optic port's 1000 Mbps link is

active

Blinking Data is being transmitted at 1000

Mbps

Off

Fiber Optic port’s 1000 Mbps link is

inactive

AMBER

Fiber optic port's 100 Mbps link is

active

Blinking

Data is being transmitted at 100 Mbps

Off

Fiber Optic port’s 100 Mbps link is

inactive

- 8 -

P1 to P8

(10/100M TP

ports)

GREEN

The corresponding port’s 100 Mbps

link is active

Blinking

Data is being transmitted at 100 Mbps

Off

The corresponding port’s 100 Mbps

link is inactive

AMBER

The corresponding port’s 10 Mbps link

is active

Blinking

Data is being transmitted at 10 Mbps

Off The corresponding port’s 10

Mbps link

is inactive

P1 to P8

(PoE+ ports)

GREEN

The corresponding port is connected

to an IEEE 802.3at power device

Blinking

Over current or short circuit on the

power device with IEEE 802.3at

standard

Off

The corresponding port is not

connected to a power device with IE

802.3at standard

AMBER

The corresponding port is connected

to a power device with IEEE 802.3af

standard

Blinking

Once per second:

Detecting error on the power device

Twice per second:

Over current or short circuit on the

power device with IEEE 802.3af

standard

Off

The corresponding port is not

connected to a power device with IEEE

802.3af standard

Specifications

Technology

Standards

IEEE 802.3af/at for Power-over-Ethernet

IEEE 802.3 for 10BaseT

IEEE 802.3u for 100BaseT(X) and 100BaseFX

IEEE 802.3ab for 1000BaseT(X)

IEEE 802.3z for 1000BaseX

IEEE 802.3x for Flow Control

IEEE 802.1D-2004 for Spanning Tree Protocol

IEEE 802.1w for Rapid STP

IEEE 802.1s for Multiple Spanning Tree Protocol

IEEE 802.1Q for VLAN Tagging

IEEE 802.1p for Class of Service

IEEE 802.1X for Authentication

IEEE 802.3ad for Port Trunk with LACP

Protocols

IGMP v1/v2, GMRP, GVRP, SNMPv1/v2c/v3, DHCP

Server/Client, BootP, TFTP, SNTP, SMTP, RARP,

RMON, HTTP, HTTPS, Telnet, SSH, Syslog, DHCP

Option 66/67/82, EtherNet/IP, Modbus/TCP, LLDP,

IEEE 1588 PTP V2, IPv6, NTP Server/Client

MIB

MIB-II, Ethernet-like MIB, P-BRIDGE MIB,

Q-BRIDGE MIB, Bridge MIB, RSTP MIB, RMON MIB

Group 1, 2, 3, 9

- 9 -

Flow Control

IEEE 802.3x flow control, back pressure flow control

Interface

Fast Ethernet 8-port 10/100Base T(X) or PoE+ 10/100BaseT(X)

2 modular slots for any 8-, or 6-port Interface

Modules with 10/100BaseT(X), 100BaseFX (SC/ST

connector), 100Base SFP, or PoE+ 10/100BaseT(X)

Gigabit Ethernet

4-port 10/100/1000BaseT(X) or 100/1000Base SFP

Console Port

USB-serial console (Type B connector)

LED Indicators PWR1, PWR2, EPS1, EPS2, STATE, FAULT,

MSTR/HEAD, CPLR/TAIL

Alarm Contact

1 relay output with current carrying capacity of 2 A

@ 30 VDC

Power Requirements

Input Voltage

HV models:

110/220 VAC (85 to 264 VAC) and

48 VDC (46 to 57 VDC)

48 models: 48 VDC (46 to 57 VDC)

Input Current

(without IM-6700

modules

consumption)

HV models:

PWR input current:

(switch system)

EPS input current:

(PoE system)

Max. 0.33 A @ 110 VAC

Max. 0.24 A @ 230 VAC

x. 0.29 A @ 48 VDC

48 models:

PWR/EPS input current :

(switch and PoE systems)

Max. 0.53 A @ 48 VDC

Note: Power consumption of PoE devices not included.

Overload Current

Protection

Present

Reverse Polarity

Protection

Present

Physical Characteristics

Housing

IP30 protection

Dimensions

440 x 44 x 280 mm (17.32 x 1.37 x 11.02 in)

Weight

IKS-6728-8PoE-4GTXSFP-HV-HV-T: 4250 g

IKS-6728-8PoE-4GTXSFP-HV-T: 4150 g

IKS-6728-8PoE-4GTXSFP-48-48-T: 4250 g

IKS-6728-8PoE-4GTXSFP-48-T: 4150 g

Installation

19’’ rack mounting

Environmental Limits

Operating Temp.

-40 to 75°C (-40 to 167°F)

Storage Temp.

-40 to 85°C (-40 to 185°F)

Ambient Relative

Humidity

5 to 95% (non-condensing)

Standards and Certifications

Safety

UL 60950-1, EN 60950-1

EMI

FCC Part 15 Subpart B Class A, EN 55022 Class A

EMS

EN 61000-4-2 (ESD) Level 3, EN 61000-4-3 (RS)

Level 3, EN 61000-4-4 (EFT) Level 3, EN 61000-4-

(Surge) Level 3, EN 61000-4-6 (CS) Level 3, EN

61000-4-8, EN 61000-4-11

Note: For better conductive radiation immunity, ST

cable is recommended.

Rail Traffic

EN 50121-4 (pending)

- 10 -

Shock

IEC 60068-2-27

Freefall

IEC 60068-2-32

Vibration

IEC 60068-2-6

Warranty

Warranty Period

5 years

Details

See www.moxa.com/warranty

Rack Mounting Instructions

1. Elevated Operating Ambient: If installed in a closed or multi-unit

rack assembly, the operating ambient temperature of the rack

environment may be greater than room ambient. Therefore,

consideration should be given to installing the equipment in an

environment compatible with the maximum ambient temperature

(Tma) specified by the manufacturer.

2. Reduced Air Flow: Installation of the equipment in a rack should

be such that the amount of air flow required for safe operation of the

equipment is not compromised.

3. Mechanical Loading: Mounting of the equipment in the rack

should be such that a hazardous condition is not achieved due to

uneven mechanical loading.

4. Circuit Overloading: Consideration should be given to the

connection of the equipment to the supply circuit and the effect that

overloading of the circuits might have on overcurrent protection and

supply wiring. Appropriate consideration of equipment nameplate

ratings should be used when addressing this concern.

5. Reliable Grounding: Reliable grounding of rack-mounted

equipment should be maintained. Particular attention should be

given to supply connections other than direct connections to the

branch circuit (e.g. use of power strips).

NOTE

The rackmount ears can be equipped on the front or rear of Moxa

IKS-6728-8PoE switch.

Restricted Access Locations

•This equipment is intended to be used in Restricted

Access Locations, such as a computer room, with

access limited to SERVICE PERSONAL or USERS

who have been instructed on how to handle the

metal chassis of equipment that is so hot that

special protection may be needed before touching it. The location

should only be accessible with a key or through a security identity

system.

•External metal parts of this equipment are extremely hot!! Before

touching the equipment, you must take special precautions to protect

your hands and body from serious injury.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Moxa Technologies Schalten Handbücher

Moxa Technologies

Moxa Technologies EDS-G2008-EL Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPort 404 Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDS-G508E-T Handbuch

Moxa Technologies

Moxa Technologies ioLogik E1200 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDS-405A Handbuch

Moxa Technologies

Moxa Technologies EDS-G205-1GTXSFP-T Handbuch

Moxa Technologies

Moxa Technologies ToughNet TN-G4500 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDS-505A Handbuch

Moxa Technologies

Moxa Technologies MDS-G4000 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies TN-5308-LV Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPort 400A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDS-516A Series Handbuch

Moxa Technologies

Moxa Technologies EDS-516A Series Handbuch

Moxa Technologies

Moxa Technologies EtherDevice EDS-P510 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDS-G509 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies PowerTrans PT-7728-F-24 Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDS-510A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies MDS-G4000-4XGS Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies PT-7528 Handbuch

Moxa Technologies

Moxa Technologies ETHERDEVICE EDS-305 Handbuch

Moxa Technologies

Moxa Technologies SPL-24 Bedienungsanleitung

Moxa Technologies

Moxa Technologies NSwitch Outdoors Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDS-508 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies TN-G4516-8GPoE-4XGPoE-WV-T Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung