Moxa Technologies MDS-G4000-4XGS Series Bedienungsanleitung

P/N: 1802040000021

*1802040000021*

MDS-G4000-4XGS/

MDS-G4000-L3-4XGS Series

Quick Installation Guide

Version 1.1, September 2022

Technical Support Contact Information

www.moxa.com/support



- 2 -

Package Checklist

Moxa’s MDS-G4000-4XGS/MDS-G4000-L3-4XGS Series industrial

modular DIN-rail switch is shipped with the following items. If any of

these items are missing or damaged, please contact your customer

service representative for assistance.

•1 MDS-G4000-4XGS or MDS-G4000-L3-4XGS switch

•Pre-installed DIN-rail kit

•2 screws (M4 x 8 mm & M3 x 8 mm)

•Quick installation guide (printed)

•Substance Disclosure Table

•Product Certificate of Quality Inspection (Simplified Chinese)

•Product Notices (Simplified Chinese)

•Warranty card

NOTE

You can find information and software downloads on the

relevant p

roduct pages located on Moxa’s website:

www.moxa.com

Default Settings

•IP address: 192.168.127.253

•Subnet mask: 255.255.255.0

•Username: admin

•Password: moxa

Panel Layouts

1. System status LEDs (from left to right, top to bottom)

STATE, FAULT, MASTER/HEAD, COUPLER/TAIL, and SYNC LED

indicators

2. USB storage port

3. Module Status

4. Switch and Control Module slot 1 (embedded)

5. Ethernet module slot 2

6. Ethernet module slot 3

7. External power input status from EPS

8. Ethernet module slot 4

9. Ethernet module slot 5

10. Ethernet module slot 6

11. Ethernet module slot 7

- 3 -

12. External Power Supply (EPS) input for PoE

13. Redundant power module slot 1

14. Redundant power module slot 2

15. RS-232 console port with RJ45 interface

16. Reset button (Pin hole 0.9 mm diameter)

17. Relay output and Digital Input port

18. Relay output

19. Power input

20. Grounding screw

Dimensions

MDS-G4012-4XGS and MDS-G4012-L3-4XGS Series

MDS-G4020-4XGS and MDS-G4020-L3-4XGS Series

MDS-G4028-4XGS and MDS-G4028-L3-4XGS Series

Unit: mm (inch)

Ethernet Modules (Hardware Rev.2.0.0 and above)

LM-7000H-4GTX

LM-7000H-4GSFP

LM-7000H-4GPoE

LM-7000H-4TX

- 4 -

LM-7000H-4PoE

Power Modules (Hardware Rev.2.1.0 and above)

PWR-HV-P48-A

PWR-LV-P48-A

PWR-HV-NP

PWR-LV-NP

DIN-rail Dimension and Instructions

Unit: mm (inch)

1. Insert the upper lip of the DIN rail into the DIN-rail mounting kit.

2. Press the device towards the DIN rail until it snaps into place.

3. Pull down the two latches one by one to release the DIN-rail kit

and lift up to remove the device from the DIN rail.

NOTE

The DIN-rail must use TS35 (15 mm) specification for the MDS-

G4000-4XGS/MDS-G4000-L3-4XGS Series.

- 5 -

Wall Mount Dimension and Instructions (Optional:

WK-112-01)

NOTE

The wall-mount kit is certified for Hazardous Location usage.

Mounting the switch to a wall requires four screws per

kit

(there are two kits). The heads of the screws

should be between 6.0 to 9.0 mm in diameter, and the

diameter of screw thread should be between 3.5 to 4

mm, as shown in the figure on the right. Use the

switch with the wall

-mounting kit attached as a guide

to mark the correct locations of the eight screws.

MDS-G4012-4XGS and MDS-G4012-L3-4XGS Series

MDS-G4020-4XGS and MDS-G4020-L3-4XGS Series

MDS-G4028-4XGS and MDS-G4028-L3-4XGS Series

Please note, there are two wall-mount kit screws for the MDS Series

(M4 x 8 mm and M3 x 6 mm).

- 6 -

Rack-mounting Kit Dimensions and Instructions

(Optional: RK-3U-02)

Please refer to the RK-3U-02 Series QIG.

Matters That Require Attention

1. Elevated Operating Temperature:If installed in a closed or

multi-unit rack assembly, the operating ambient temperature of

the rack environment may be greater than room temperature.

Therefore, consideration should be given to installing the

equipment in an environment compatible with the maximum

ambient temperature (Tma) specified by the manufacturer.

NOTE

In order to ensure reliable operations, please make sure the

operating temp

erature of the environment does not exceed the

spec. When mounting a rack

-mounted switch with other

operating units in a cabinet without forced ventilation, it is

recommended that 1U of space is reserved between each rack

mounted switch and/or device.

2. Required Air Flow: Installation of the equipment in a rack should

be such that the amount of air flow required for safe operation of

the equipment is not compromised.

3. Mechanical Loading: Mounting of the equipment in the rack

should be such that a hazardous condition is not achieved due to

uneven mechanical loading.

4. Circuit Overloading: Consideration should be given to the

connection of the equipment to the supply circuit and the effect

that overloading of the circuits might have on overcurrent

protection and supply wiring. Appropriate consideration of

equipment nameplate ratings should be used when addressing this

concern.

5. Reliable Grounding: Reliable grounding of rack-mounted

equipment should be maintained. Particular attention should be

given to supply connections other than direct connections to the

branch circuit (e.g. use of power strips).

ATTENTION

Safety First

Be sure to disconnect the power cord before installing and/or

wiring your Ethernet Switch. Calculate the maximum

possible

current in each power wire and common wire. Observe all

electrical codes dictating the maximum current allowable for

each wire size. If the current goes above the maximum ratings,

the wiring could overheat,

which can cause serious damage to

your equipment.

WARNING

When end users are

using Optical SFP Communications

modules, these must be limited to Laser Class 1.

- 7 -

Connecting the Power Inputs

NOTE

The required power module depends on the choice of LM-7000H

module. Refer to the following power/module combination

requirements.

•

LM-7000H non-PoE modules:

Any power module

•

LM-7000H PoE modules:

PWR-HV-P48-A, PWR-LV-P48-A only

The MDS-G4000-4XGS/MDS-G4000-L3-4XGS Series supports 4 types of

power supply:

•PWR-HV-P48-A: one 110/220 VAC/VDC (90 to 264 VAC, 88 to 300

VDC), one 48 VDC PoE power input for PoE+ ports.

•PWR-LV-P48-A: one 24/48 VDC (18 to 72 VDC), one 48 VDC PoE

power input for PoE+ ports.

•PWR-HV-NP: one 110/220 VAC/VDC (90 to 264 VAC, 88 to 300

VDC) power input.

•PWR-LV-NP: one 24/48 VDC (18 to 72 VDC) power input.

For the PWR-HV-P48-A, the 110/220 VAC/VDC power supplies provide

power to the switch. Separate 48 VDC power supplies are required to

provide power to all PoE+ ports (50 to 57 VDC is recommended for

IEEE 802.3at devices. The maximum PoE output from an external

power supply is 720 W when the operating temperature is under 60°C;

360 W when the operating temperature is under 75°C.)

For the PWR-LV-P48-A models, the 24/48 VDC power supplies provide

power to the switch. Separate 48 VDC power supplies are required to

provide power to all PoE+ ports (50 to 57 VDC is recommended for

IEEE 802.3at devices. The maximum PoE output from an external

power supply is 720 W when the operating temperature is under 60°C;

360 W when the operating temperature is under 75°C.)

For the PWR-HV-NP, the 110/220 VAC/VDC power supplies provide

power to the switch. For the PWR-LV-NP, the 24/48 VDC power supplies

provide power to the switch.

Power Terminal Blocks

The connections for the power input are on the power modules.

- 8 -

PWR-HV-P48-A/PWR-HV-NP

Step 1: Insert the neutral/line (L/N/Ground) AC wires into the

terminals.

Step 2: Insert the terminal block connector into the terminal block

receptor.

PWR-LV-P48-A/PWR-LV-NP

Step 1: Insert the negative/positive (-/+) DC wires into the terminals.

Step 2: Insert the terminal block connector prongs into the terminal

block receptor.

PoE Power Terminal Blocks

Step 1: Insert the negative/positive DC wires into the -/+ terminals,

respectively.

Step 2: Insert the terminal block connector prongs into the terminal

block receptor.

NOTE

In order to have higher levels of protection against surge, it is

suggested to install

a surge protector in front of the power

input of the PoE powered device so that it is suitable for use in

IEC 61850 conditions.

WARNING

When wiring the power input, we suggest using the cable type -

AWG

(American Wire Gauge) 16 (1.31 mm2) and the

corresponding pin type cable terminals. The rated temperature

of the wiring should be at least 105°C and the wire type should

be CU.

- 9 -

NOTE

When two power units are installed on the MDS-G4000-

4XGS/MDS

-G4000-L3-4XGS Series

switch, both power units will

be activated simultaneously, which will enab

le power

redundancy.

NOTE

The reverse power input connection will not activate the device

or PoE input. In addition, the PoE will only activate when the

external power supply is installed on the same power unit.

Wiring the Relay Contact

Each power module has one relay output that can provide two types of

relay output. Refer to the table below for detailed information.

The relay contact is used to detect user-configured events. Two wires

are attached to the relay pins with normally close and normally open

options.

FAULT: The relay contact of the 3-pin terminal block connector is used

to detect user-configured events. The module provides normally open

and normally closed circuits depending on what the user chooses. For

pin definitions, refer to the table below.

Relay Connection

Power Off

Boot up Ready

Event Trigger

NO and COM

Closed Circuit

Open Circuit

Closed Circuit

NC and COM

Open Circuit

Closed Circuit

Open Circuit

WARNING

When wiring the relay contact, we suggest using the cable type

AWG (American Wire Gauge) 16-21 (1.31-0.412 mm2) and

the corresponding pin type

cable terminals. The rated

temperature of the wiring should be at least 105°C

and the wire

type should be CU.

Digital Input/Output

Digital Output

1 relay output with a current carrying capacity of 2 A @ 30 VDC.

Digital Input

1 digital output with the same ground, but electrically isolated from the

electronics.

•+13 to +30 V for state 1

•-30 to +1 V for state 0

•Max. input current: 8 mA

- 10 -

WARNING

When wiring the Digital Input/Output contact, we suggest using

the cable

type - AWG (American Wire Gauge) 16-28 (1.31-

0.081 mm

2) and the corresponding pin type cable terminals.

The rated temperature of the wiring should be at least 105°C

and the wire type should be CU.

Installing and Removing the Ethernet Modules

The Ethernet modules are hot-swappable for the same module type.

You can mount or remove the Ethernet module while the device is

operating.

NOTE

When performing a cold start, you cannot remove and

insert a module before the device has fully booted up as

this will cause the module to fail initialization.

The default module is 4XGS. If this is the first time

mounting a 4TX or SFP module, please reboot the switch

after inserting it. The hot-swappable function, as defined

above, will work after the device is rebooted for the first

time.

When swapping out a slotted module with a different type

of module, it is recommended to reconfigure the settings

reset the device to factory default settings after rebooting

the switch.

The installation procedure is as follows:

1. Insert the Ethernet module straight into the slot

2. Fasten the module to the device by tightening the 2 screws. The

tightening torque is 3.5 kgf-cm (0.35 Nm)

The removal procedure is as follows:

1. Loosen the 2 screws of the module

2. Pull the module out of the slot

3. Insert the dummy module into the slot in order to have better

protection against dust and EMI

4. Fasten the dummy module using the 2 screws. The tightening

torque is 4 kgf-cm (0.4 Nm)

Installing and Removing the Power Modules

The power supply units are hot-swappable when both power modules

are installed. You can mount or remove the power supply units while

the device is operating.

The installation procedure is as follows:

1. Insert the power unit straight into the slot

2. Fasten the unit to the device by tightening the 2 screws. The

tightening torque is 3.5 kgf-cm (0.35 Nm)

The removal procedure is as follows:

1. Loosen the 2 screws of the module

2. Pull the module out of the slot

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Moxa Technologies Schalten Handbücher

Moxa Technologies

Moxa Technologies EtherDevice EDS-405A/408A Series Handbuch

Moxa Technologies

Moxa Technologies IESH-MB205G-C2E-R Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPort 400A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDS-4012 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies PT-7710 Series Handbuch

Moxa Technologies

Moxa Technologies EDS-P206A-4PoE-SS-SC Handbuch

Moxa Technologies

Moxa Technologies EDS-516A Series Handbuch

Moxa Technologies

Moxa Technologies EtherDevice EDS-828 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDS-516A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDS-518A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies MDS-G4000-L3-4XGS Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDS-G205-T Handbuch

Moxa Technologies

Moxa Technologies EDS-600 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies PowerTransPT-7528 Series Handbuch

Moxa Technologies

Moxa Technologies PT-508 Series Handbuch

Moxa Technologies

Moxa Technologies ToughNet TN-5516 Series Handbuch

Moxa Technologies

Moxa Technologies EDS-516A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ETHERDEVICE EDS-305 Handbuch

Moxa Technologies

Moxa Technologies EtherDevice EDS-4008 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies TN-5516A Series Handbuch

Moxa Technologies

Moxa Technologies TN-5305 Series Handbuch

Moxa Technologies

Moxa Technologies EDS-G4014 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDS-510A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies IKS-6728 Series Handbuch

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung