Moxa Technologies NPort S8000 Series Bedienungsanleitung

P/N: 1802080000015

*1802080000015*

NPort S8000 Series

Quick Installation Guide

Edition 6.1, November 2018

Technical Support Contact Information

www.moxa.com/support

Moxa Americas:

Toll

-free: 1-888-669-2872

Tel:

1-714-528-6777

Fax:

1-714-528-6778

Moxa China (Shanghai office):

Toll

-free: 800-820-5036

Tel:

+86-21-5258-9955

Fax:

+86-21-5258-5505

Moxa Europe:

Tel:

+49-89-3 70 03 99-0

Fax:

+49-89-3 70 03 99-99

Moxa Asia-Pacific:

Tel:

+886-2-8919-1230

Fax:

+886-2-8919-1231

Moxa India:

Tel:

+91-80-4172-9088

Fax:

+91-80-4132-1045



- 2 -

Overview

The Moxa NPort S8000 series fully integrates an industrial serial device

server and redundant managed Ethernet switch into a single device,

making it easy to enable your serial devices to operate over a network

and connect Ethernet-enabled devices in industrial field applications.

Package Checklist

Before installing the NPort S8000, verify that the package contains the

following items:

•1 NPort S8000 combo switch / serial device server

•CBL-RJ45F9-150 cable

•Documentation and software CD

•Quick installation guide

•Warranty card

Optional Accessories (must be ordered separately)

•Wall-mounting kit

Please notify your sales representative if any of the above items are

missing or damaged.

Hardware Introduction

The NPort S8455I integrates 5 Ethernet ports and 4 male DB9 ports

for the RS-232/422/485 serial port.

NPort S8455I-SS-SC/NPort S8455I-MM-SC integrates 2 fiber ports,

3 Ethernet ports, and 4 male DB9 ports for the RS-232/422/485 serial

port.

The NPort S8458 integrates 4 fiber ports, 4 Ethernet ports, and 4

male DB9 ports for the RS-232/422/485 serial port.

Reset Button—Hold the Reset button for 5 seconds to load factory

default settings: Use a pointed object, such as a straightened paper clip

or toothpick, to press the reset button. This will cause the Ready LED to

blink on and off. The factory defaults will be loaded once the Ready LED

stops blinking (after about 5 seconds). At this point, you should release

the reset button.

- 3 -

LED Indicators—The NPort S8000’s front panel contains some LED

indicators as described in the following table.

Type

Color

Meaning

PW 1

Green

Power 1 input

PW 2

Green

Power 2 input

Ready

Red

Steady On: Power is on, and the NPort is

booting up.

Blinking: Indicates a LAN-IP conflict, or the

DHCP or BOOTP server did not respond

properly.

Green

Steady On: Power is on, and the NPort is

functioning normally.

Blinking: The device server has been located

by the Administrator’s location function.

Off

Power is off, or power error condition exists.

Master

Green

When the NPort is the Master of this Turbo

Ring.

Blinking

When the NPort is the Ring Master of this

Turbo Ring and the Turbo Ring is

disconnected.

Coupler

Green

When the NPort enables the coupling function

to form a backup path

Serial Port TX

Green

The serial port is transmitting data.

Serial Port RX

Yellow

The serial port is receiving data.

Link (FX)

Green

The FX port’s 100 Mbps is active

Blinking

Data is being transmitted/received at 100

Mbps

Link

Green

The 100 Mbps Ethernet connection is active.

Yellow

The 10 Mbps Ethernet connection is active.

Hardware Installation Procedure

STEP 1: After removing the NPort S8000 from the box, attach the

power adaptor.

STEP 2: Connect the NPort S8000 to a network. Use a standard

straight-through Ethernet cable to connect to a hub or switch. When

setting up or testing the NPort S8000, you might find it convenient to

connect directly to your computer’s Ethernet port. In this case, use a

crossover Ethernet cable.

STEP 3: Connect the NPort S8000’s serial port to a serial device.

STEP 4: Mount the NPort S8000 to either a wall or DIN-rail, as

described below.

- 4 -

Wall Mounting (optional)

In high-vibration environments, we suggest using the NPort S8000’s

wall-mount kit to fix. The installation procedure is described below:

STEP 1: Remove the aluminum DIN-rail attachment plate from the

NPort S8000’s rear panel and then attach the wall-mount plates with

M3 screws.

STEP 2: Four screws are required. Use the NPort

S8000

, with wall-mount plates attached, as a guide

mark the correct locations of the 4 screws. The

heads of the

screws should be less than 6.0 mm in

diameter, and the shafts

should be less than 3.5 mm

in diameter.

NOTE

Before tightening the screws into the wall, make sure the screw

head and shank size

s are suitable by inserting one of the

screws into one of the keyhole

-shaped openings of the wall-

mounting plates.

Do not screw the screws in completely—leave about 2 mm to allow

room for sliding the wall-mount panel between the wall and the screws.

STEP 3: Once the screws are fixed to the wall, insert the four screw

heads through the large parts of the keyhole-shaped openings and slide

the NPort S8000 downwards as indicated. Tighten the four screws for

added stability.

DIN-rail Mounting (optional)

DIN-rail attachments can be purchased separately to

attach the product to

a DIN-rail. When snapping the

attachments to the DIN

-rail, make sure that the stiff

metal springs are at the top.

- 5 -

Turbo Ring DIP Switch Settings

The default setting for each DIP switch is OFF. The

following table explains the effect of setting the DIP switch

to the ON

position.

Turbo Ring Settings

DIP

DIP 1

DIP 2

DIP 3

DIP 4

–

Ring Master

Ring Coupling

port

DIP 1, 2, 3

–

Enable

Activates

Default

OFF

–

Disable

Disabled

Turbo Ring V2 Settings

DIP

DIP 1

DIP 2

DIP 3

DIP 4

Ring Coupling Ring Master

Ring Coupling

port

DIP 1, 2, 3

ON Backup port

Enable

Enable Enable Activates

Default OFF

Primary port

Enable

Disable Disable Disabled.

Software Installation Information

For the NPort’s configuration, the default IP address of the NPort is:

LAN: Static IP = 192.168.127.254; netmask = 255.255.255.0

You may log in with the account name admin and password moxa to

change any settings to meet your network topology (e.g., IP address)

or serial device (e.g., serial parameters). You may also refer to Moxa

support website https://www.moxa.com/support for user’s manual,

driver, SNMP MIB, and NPort Search Utility.

NOTE

For NPort with DB Male serial ports, you may refer to the DB9

Male Port

s pin assignment section to loop back pin 2 and pin 3

for the RS-232 interface to carry out a self test on the device.

Pin Assignments and Cable Wiring

DB9 Male Port Pinouts

Pin RS-232

RS-422/

RS-485-4w

RS-485-2w

DCD

TxD-(A)

–

RxD

TxD+(B)

–

TxD

RxD+(B)

Data+(B)

DTR

RxD-(A)

Data-(A)

GND

DSR

–

RTS

–

CTS

–

- 6 -

Wiring the Relay Contact

The NPort S8000 has two sets of relay outputs: relay 1 and relay 2.

Each relay contact consists of two contacts of the terminal block on the

NPort S8000’s top panel. Refer to the next section for detailed

instructions on how to connect the wires to the terminal block

connector and how to attach the terminal block connector to the

terminal block receptor. The two contacts used to connect the relay

contacts work as follows (see illustration below):

The fault circuit will open if

A relay warning event is triggered, OR

The NPort S8000 is the Master of this Turbo

Ring, and the Turbo Ring is disconnected, OR

Start-up fails.

none of these three conditions are met, the fault

circuit will remain closed.

Wiring the Digital Inputs

The NPort S8000 unit has two sets of digital inputs: DI 1 and DI 2.

Each DI consists of two contacts of the 6-pin terminal block connector

on the NPort S8000’s top panel. The remaining contacts are used for

the NPort S8000’s two DC inputs. The top and front views of one of the

terminal block connectors are shown below.

Take the following steps to wire the digital inputs:

Insert the negative (ground) or positive DI

wires into the terminals.

To keep the DI wires from getting loose, use a

small flat-blade screwdriver to tighten the wire-

clamp screws on the front of the terminal block

connector.

Insert the plastic terminal block connector

prongs into the terminal block receptor, which

is located on the NPort 8000’s top panel.

Wiring the Redundant Power Inputs

The NPort S8000 unit has two sets of power inputs: power input 1 and

power input 2. The top two contacts and the bottom two contacts of the

6-pin terminal block connector on the top panel are used for the NPort

S8000’s two power inputs. The top and front views of one of the

terminal block connectors are shown below.

Take the following steps to wire the redundant power inputs:

1. Insert the negative/positive DC wires into the V-/V+ terminals.

2. To keep the DC wires from pulling loose, use a small flat-blade

screwdriver to tighten the wire-clamp screws on the front of the

terminal block connector.

3. Insert the plastic terminal block connector prongs into the terminal

block receptor, which is located on the NPort S8000’s top panel.

Andere Handbücher für NPort S8000 Series

Inhaltsverzeichnis

Andere Moxa Technologies Schalten Handbücher

Moxa Technologies

Moxa Technologies EDS-P308 Series Handbuch

Moxa Technologies

Moxa Technologies PowerTrans PT-7728-PTP Handbuch

Moxa Technologies

Moxa Technologies TN-5308-LV-T Bedienungsanleitung

Moxa Technologies

Moxa Technologies PowerTrans PT-7528-24TX-WV Bedienungsanleitung

Moxa Technologies

Moxa Technologies S9450I Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDS-205 Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDS-516A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDS-P510 Series Handbuch

Moxa Technologies

Moxa Technologies PT-7710 Series Handbuch

Moxa Technologies

Moxa Technologies EDS-4014 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDS-516A Series Handbuch

Moxa Technologies

Moxa Technologies EtherDevice EDS-516A-T Handbuch

Moxa Technologies

Moxa Technologies EtherDevice EDS-P510A-8PoE Series Handbuch

Moxa Technologies

Moxa Technologies RKS-G4028 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ToughNet TN-5524-8PoE-P24-T Bedienungsanleitung

Moxa Technologies

Moxa Technologies TN-G6512 Serie Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPORT 6610 Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDS-P510-T Bedienungsanleitung

Moxa Technologies

Moxa Technologies OnCell G3111 Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDS-G205A-4POE-1GSFP-T Bedienungsanleitung

Moxa Technologies

Moxa Technologies TN-5305 Series Handbuch

Moxa Technologies

Moxa Technologies UPort 404 Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDS-205A series Handbuch

Moxa Technologies

Moxa Technologies EDS-P206A-4PoE-SS-SC Handbuch

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung