MRMC BROADCAST TALOS Bedienungsanleitung

CRANES AND RIGS | BROADCAST | HEADS & DSLR | PRODUCT PHOTOGRAPHY | RENTALS

Broadcast

Talos

Quick Start Guide

QSG Product code: MRMC-2113-00

Product Covered: MRMC-2081-00

Broadcast Talos Quick Start Guide

QSG Product code: MRMC-2113-00

Product Covered: MRMC-2081-00

No part of this publication may be reproduced, transmitted, or translated

by any means — graphical, electronic, or mechanical — including

photocopying, recording, taping, or storage in an information retrieval

system, without the express written permission of Mark Roberts Motion

Control.

Although every care has been taken to ensure that the information in this

document is accurate and up to date, Mark Roberts Motion Control

continuously strives to improve their products and may make changes to

the hardware, firmware, and software described in this document. Mark

Roberts Motion Control therefore cannot be held responsible for any

error or omission in this document.

All product names mentioned herein are the trademarks or registered

trademarks of their respective owners.

Contact information

Mark Roberts Motion Control Ltd.

Unit 3, South East Studios

Blindley Heath

Surrey

RH7 6JP

United Kingdom

Telephone: +44 (0) 1342 838000

E-mail: [email protected]m (sales and general enquiries)

[email protected]m (customer support)

Web: www.mrmoco.com

www.mrmocorentals.com

Broadcast Talos Quick Start Guide

iii

Broadcast TalosQuick Start GuideBroadcast TalosQuick Start Guide

Contents

Chapter 1 Assembling the hardware .............................................. 1

Safety........................................................................................1

Overview .................................................................................1

General procedure .................................................................3

Mounting the head.................................................................4

Mounting Talos on the Track ...............................................5

Connecting the cables ...........................................................8

Umbilical cable - base - turret connections ..............8

Rail Connector Panel - Flight Case connections .......

Attaching the track motor pinch wheel to Talos ....11

Removing the trolley wheels .....................................13

Appendix 1 Talos panels.................................................................. 16

Panel summary.....................................................................16

Appendix 2 Specifications............................................................... 18

Broadcast Talos Quick Start Guide

Broadcast TalosQuick Start GuideBroadcast TalosQuick Start Guide

Chapter 1 Assembling the hardware

Safety

•Due to the size and weight of Talos components, it is recommended

that you use at least two people to assemble it.

•Do not use around flammable gas. All electrical equipment can

generate sparks that can ignite flammable gas.

•Talos has powerful motors that can pinch, so take care not to get

your hands trapped in the rig or cabling.

•Keep the equipment dry. The system has not been made

weatherproof. Do not use with wet hands.

•Keep cables tidy. Use cable ties to keep them out of harm’s way. If

you have a head with slip rings then make use of them; avoid

running any cables between Talos and the rotating head or camera if

possible.

•Use a 240V AC power supply that is properly earthed (grounded).

This is not only for safety reasons; electrical noise on an unearthed

system can make axes controller boards trip out unpredictably,

interrupting the shoot and creating intermittent problems that can

be difficult to trace.

Overview

Thank you for using the Broadcast Talos motion control rig from Mark

Roberts Motion Control (MRMC). Talos is designed for reliable day-in,

day-out use in professional studio and Outside Broadcast environments.

Broadcast Talos is typically part of a complete motion control system that

includes:

Broadcast Talos Quick Start Guide

Talos itself.

A head such as an Ulti-Head or SFH-50, on which you mount

your video camera.

A Teleprompter

A Windows PC running MRMC Software.

Additional controllers such as a Broadcast Panel, Hand-Held

Box (HHB), Mimic Handwheels or Pan Bars.

Broadcast Talos Quick Start Guide

General procedure

1. Mount the Head- page 4.

2. Mount Talos on a track - page 5. If you want, you can mount the

Talos base onto the track first and then build Talos on the track

starting with step 2.

3. Connect the cables - page 8.

Broadcast Talos Quick Start Guide

Mounting the head

If not already mounted, you can mount the head under-slung as shown or

over-slung.

Mount the head to the swan neck with the single bolt and disk,

making sure that the key on the head fits into the slot in the neck.

Key

Slot

Disk

Example: Ulti-Head

Broadcast Talos Quick Start Guide

Mounting Talos on the Track

1. Roll the Talos to a position just off the end of the track, raise the rig

on its wheels high enough to go over the track using the wheel

cranks, and rotate the Talos on its wheels to be the correct way

around so that the track motor gear on the Talos underside is on the

toothed side of the rack. Do not engage the teeth yet; just make

sure the rig is the correct way around for the track.

2. On the underside of the Talos, remove the pinch wheel if you haven’t

already done so and push the track motor out of the way on its

sliding bearings, so that the track motor gear will not interfere with

the Rack on the track. (For details of removing the pinch wheel,

follow the procedure on page 11 in reverse order.) Do not slide the

pinion gear too far away from the rack when moving it into place,

the rear (inner) track motor mounting bolt will hit the racking as

you drop the rig down.

3. Push the Talos on its wheels over the track about a metre, being

careful not to push the track motor gear against the rack while

moving.

4. Carefully lower the Talos onto the track, ensuring that the track

motor gear on the underside of the Talos clears the rack.

5. Apply the brakes to the wheels to keep them from pivoting against

the track (the brakes affect both rotation and pivot), and raise the

wheels off the ground so the full Talos weight is taken by the track.

Broadcast Talos Quick Start Guide

6. .Add the cable chain to the tray such that the panel can be mounted

at the end of the rails and the bracket at other end can be secured

with Talos.

7. Secure the cable chain with the cable tray top.

8. Attach the track motor pinch wheel on the underside of the Talos,

described in Attaching the track motor pinch wheel to Talos on page

11.

9. Add the cable tray cover strips along the length of the track. The

thicker one is for the side closer to the edge of the rail and thinner

one for the other side. Secure using nylocks.

Thicker strip Thinner strip

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere MRMC Robotik Handbücher

MRMC

MRMC Bolt X Bedienungsanleitung

MRMC

MRMC CINEBOT Bolt Jr+ Bedienungsanleitung

MRMC

MRMC Bolt Jr+ Bedienungsanleitung

MRMC

MRMC Studiobot-165 Bedienungsanleitung

MRMC

MRMC MRMC-2165-00 Bedienungsanleitung

MRMC

MRMC TX90L Bedienungsanleitung

MRMC

MRMC PTA-1 Bedienungsanleitung

MRMC

MRMC CINEBOT MINI Bedienungsanleitung

MRMC

MRMC STUDIOBOT XL Bedienungsanleitung

MRMC

MRMC SHOWBOLT JUNIOR Bedienungsanleitung

MRMC

MRMC Bolt Junior Bedienungsanleitung

MRMC

MRMC MOVER RV13 Bedienungsanleitung

MRMC

MRMC STUDIOBOT TX90 Bedienungsanleitung

MRMC

MRMC UR10 ROBOT Mover Bedienungsanleitung

Beliebte Robotik Handbücher anderer Marken

STEMCenter USA

STEMCenter USA Pi-Bot v2.00 Bedienungsanleitung

SunFounder

SunFounder PiDog Bedienungsanleitung

Universal Robots

Universal Robots UR5 Bedienungsanleitung

Universal Robots

Universal Robots E Series Bedienungsanleitung

YASKAWA

YASKAWA MOTOMAN-MPL80 II Bedienungsanleitung

EFORT

EFORT ECR5 Gebrauchsanweisung

Epson

Epson C8 Series Bedienungsanleitung

WowWee

WowWee ROBOQUAD Bedienungsanleitung

Milvus Robotics

Milvus Robotics SEIT 100 Bedienungsanleitung

RoboMaster

RoboMaster AI Robot 2020 Standard Version Bedienungsanleitung

fischertechnik

fischertechnik Mini Bots Bedienungsanleitung

YASKAWA

YASKAWA MA2010 Handbuch

Abicor Binzel

Abicor Binzel iCAT mini Bedienungsanleitung

ABB

ABB OmniCore E10 Bedienungsanleitung

YASKAWA

YASKAWA Motoman DX200 Bedienungsanleitung

pitsco

pitsco Tetrix Max Bedienungsanleitung

ECOVACS

ECOVACS DEEBOT R95 Bedienungsanleitung

Feng Yuan

Feng Yuan Interstellar Warrior Bedienungsanleitung