MRMC MRMC-2058-00 Bedienungsanleitung

CRANES AND RIGS | BROADCAST | HEADS & DSLR | PRODUCT PHOTOGRAPHY | RENTALS

XL Turntable

Quick Start Guide

Product Code: MRMC-2058-00

Product Covered: MRMC-2032-01

XL Turntable Quick Start Guide

Product Code: MRMC-2058-00

Product Covered: MRMC-2032-01

No part of this publication may be reproduced, transmitted, or translated

by any means — graphical, electronic, or mechanical — including

photocopying, recording, taping, or storage in an information retrieval

system, without the express written permission of Mark Roberts Motion

Control.

Although every care has been taken to ensure that the information in this

document is accurate and up to date, Mark Roberts Motion Control

continuously strives to improve their products and may make changes to

the hardware, firmware, and software described in this document. Mark

Roberts Motion Control therefore cannot be held responsible for any

error or omission in this document.

All product names mentioned herein are the trademarks or registered

trademarks of their respective owners.

Contact information

Mark Roberts Motion Control Ltd.

Unit 3, South East Studios

Blindley Heath

Surrey

RH7 6JP

United Kingdom

Telephone: +44 (0) 1342 838000

E-mail: [email protected]m (sales and general enquiries)

[email protected]m (customer support)

Web: www.mrmoco.com

www.mrmocorentals.com

XL Turntable Quick Start Guide

iii

TurntableQuick Start GuideXL TurntableQuick Start Guide

Contents

Chapter 1 Quick Start..................................................................... 1

Important safety instructions ...............................................1

General care...................................................................1

Location .........................................................................1

Intellectual property .....................................................1

Overview ................................................................................. 2

Transporting the XL Turntable ............................................2

Lifting XL Turntable using a Gantry Hoist ...............2

Removing Castor Wheels......................................................3

Anchoring XL Turntable to the floor ..................................3

Fixing Equipment (Motion Base etc.) on XL

Turntable .................................................................................6

Connecting the Cables for XL Turntable as a

Stand-alone .............................................................................7

Using the XL Turntable as a Stand-alone............................7

Connecting the Cables for XL Turntable when used

with a Bolt on Track...............................................................9

Using the XL Turntable with Bolt on Track........................9

Brake Release ........................................................................10

Zero Position Marker ..........................................................11

Appendix 1 Specifications............................................................... 15

System Properties.................................................................15

Motion Performance............................................................16

Control/Drive Enclosure.....................................................16

Payload Mounting................................................................18

Physical Specification ..........................................................18

XL Turntable Quick Start Guide

TurntableQuick Start GuideXL TurntableQuick Start Guide

Chapter 1 Quick Start

Important safety instructions

To ensure the best from the product, please read this manual carefully.

Keep it in the safe place for future reference.

To reduce the risk of electric shock, do not remove the cover from the

unit. No user serviceable parts inside. Refer servicing to qualified

personnel.

General care

Do not force switches or external connections.

When moving the unit, disconnect the mains cable.

Do not attempt to clean the unit with chemical solvents or

aerosol cleaners, as this may damage the unit. Use a clean dry

cloth.

Do not use around flammable gas. All electrical equipment can

generate sparks that can ignite flammable gas.

Keep away from pets and children. The head has powerful

motors that can pinch, so take care not to get your hands

trapped in the head or cabling.

Keep cables tidy. Use cable ties to keep them out of harm’s way.

If you have a head with slip rings then make use of them; avoid

running any cables between the base and the rotating head or

camera.

Location

Installation of this unit should be away from sources of excessive heat,

vibration, and dust.

Intellectual property

This product includes confidential and/or trade secret property.

Therefore, you may not copy, modify, adapt, translate, distribute, reverse

engineer, or decompile contents thereof.

XL Turntable Quick Start Guide

Overview

Thank you for using the XL Turntable from Mark Roberts Motion

Control (MRMC). You can use the Turntable for day in and day out use in

product photography and filming.

The XL Turntable can be used as an additional axis of a Bolt on Track

System or as a stand-alone EtherCAT unit controlled by Flair or RTL.

XL Turntable gives you the following features:

High speed

Zero backlash

Precise movement

Removable center disc so cables or power can be fed through

to appliances

Can take weight of up to 3 tonnes

Transporting the XL Turntable

Use the 4 x M20 threaded lifting points with lifting eye bolts in

conjunction with lifting equipment.

In addition the 4 x Castor wheels can be used to manoeuvre the XL

Turntable around.

Lifting XL Turntable using a Gantry Hoist

1. Tie a lifting sling around the 4 x lifting eye bolts on the XL Turntable

and insert the hook from the gantry hoist on to it.

2. Use the gantry hoist to gently lift the XL Turntable and lower it in

position.

XL Turntable Quick Start Guide

3. Remove the gantry hook and the straps from the arm.

Removing Castor Wheels

When in position you can either jack the castor wheels up so they don’t

touch the ground or remove the castor wheels by removing the 2 x M10

cap head screws to prevent them from coming into way of the Turntable

load.

Anchoring XL Turntable to the floor

If you are setting up the XL Turntable in a permanent (or

semi-permanent) location, it is recommended that you anchor the

turntable to the ground. The following procedure tells you how to anchor

the turntable to a concrete floor.

1. Temporarily put the turntable into place where you want.

× 4 corners

5 cm

Tape

XL Turntable Quick Start Guide

2. At one corner of the turntable, use one of the two holes to draw a

circle on the concrete with a pencil, to mark the position of the hole.

You can use either hole.

Repeat for the other three corners of the turntable.

3. Add the lifting eye bolts to the 4xM20 threaded lifting points.

4. Tie straps to the lifting eye bolts and using a gantry hoist

temporarily remove the turntable and at one of the four circles that

you have drawn, draw a cross centred on the circle, to help you

precisely locate the drill bit.

Repeat for the other three corners.

5. On the 15mm diameter drill bit, put tape around the bit 5 cm from

the tip. This will help you gauge the depth of the hole in the next

step.

6. At one of the corner circles, drill a hole 5 cm deep into the concrete,

centred on the cross. When the tape on the drill bit reaches the floor,

drilling is complete.

Repeat for the other three corners.

7. Clean the four holes.

8. At one of the holes insert the drop-in

anchor insert, threads upward, all

the way to the bottom.

9. Insert the anchor spreader tool into

the drop-in anchor insert.

10. Hit the top of the anchor spreader

tool with a hammer until the anchor

is fully spread in the concrete.

11. Remove the anchor spreader tool.

12. Repeat steps 8 to 11 for the other

three corners.

13. Put the turntable in place over the

holes.

Anchor

spreader

tool

Drop-in

anchor

insert

× 4 corners

XL Turntable Quick Start Guide

14. Insert the four retaining bolts through the corners of the base and

into the drop-in anchor inserts, and tighten.

XL Turntable Quick Start Guide

Fixing Equipment (Motion Base etc.) on XL

Turntable

Use the M16 threaded holes on the outer ring to fix equipment on the XL

Turntable.

If required, you can remove the top plate to allow the cables to pass

through. To do this:

1. Remove the M16 screws from the centre plate.

2. Screw an M16 lifting eye bolt to the centre, then use it to lift the

centre plate off the turntable.

Use the cable tube in the centre of the turntable if you require cables to

pass through.

Cable tubeCentre plate

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere MRMC Drehscheibe Handbücher

MRMC

MRMC MRMC-1579-01 Bedienungsanleitung

Beliebte Drehscheibe Handbücher anderer Marken

Gemini

Gemini CDT-05 MKII Bedienungsanleitung

Rotel

Rotel RP-820 Bedienungsanleitung

Shuman

Shuman MC-250BT Bedienungsanleitung

Stanton

Stanton STR8-150 Bedienungsanleitung

Audio Technica

Audio Technica AT-LPW40WN Bedienungsanleitung

Crosley

Crosley McQueen CR7011-GY Bedienungsanleitung

Reloop

Reloop SMP-1 Bedienungsanleitung

auna

auna TT-Classic Plus Bedienungsanleitung

COMO AUDIO

COMO AUDIO Turntable Analog Bedienungsanleitung

Dual

Dual 1009 F Bedienungsanleitung

REED

REED Muse3C Bedienungsanleitung

AXIOMTEK

AXIOMTEK OPS883-H Series Bedienungsanleitung

Pioneer

Pioneer PL-71 Bedienungsanleitung

Vestax

Vestax PDX-a1 Bedienungsanleitung

Denon

Denon DP-400 Bedienungsanleitung

Dual

Dual 504 Bedienungsanleitung

Audio-Techica

Audio-Techica AT-LP60XBT Bedienungsanleitung

Goldring

Goldring G99 Bedienungsanleitung