MSI MS-1034 Bedienungsanleitung
Installation Guide
Copyright © 2006 MSI Computer Corp.
Overview:
MS-1034 is shipped out as a bare bone. Some of the components are equipped while some are not. This
installation guide provides you with the information of notebook hardware setup. Before assembling your
Notebook, please prepare the installation tools and appropriate items. If you are not clear about the
items, please contact your dealer for more information.
Package check list:
Optional Hardware Devices:
HDD, Mini PCI WLAN card, CPU, Memory
Before installing Devices in Notebook
• The peripheral devices contained herein depend on your actual system configuration.
• Third-party trademarks and names are the properties of their respective owners.
• The information contained herein is relevant to software and hardware references only and in
accordance with actual system configuration. All information is subject to change without notice.
Warning!
• Ensure power is turned off and Notebook Battery is removed before installing any hardware
devices.
• Use a grounded wrist strap before handling any computer components such as CPU, Memory,
HDD, mini-PCI Card, etc.
• Place components (CPU, Memory, HDD, mini-PCI Card, etc) on a grounded antistatic pad or on
the foam bed that came with the components whenever the components are separated from the
Notebook.
• If there are any difficulties installing hardware devices, please contact your dealer for further
information.
Open View
1. Cover latch
2. Display Panel
3. Quick Launch Buttons and Power button
4. Status LEDs
5. Keyboard
6. Touchpad
7. Stereo Speakers
Bottom View
1. CPU Compartment
2. Mini PCI Drive Compartment
3. Memory Compartment
4. Hard Disk Drive Compartment
5. Battery Unlock Button
6. Battery Pack
Rear View
Right view
Left view
Step 1: Installing CPU
1-1 Prepare a proper size flat head screw driver. Un-screw the screw until it can not go any further.
1-2 a.b.Locate the golden cut edge on the CPU’s upper right-hand corner. Then insert the CPU into the
Socket
!!!The CPU will only fit in the correct orientation!!!
1-3 Adjust the CPU socket by turning the screw. Make sure the CPU is properly installed. Then press the
CPU evenly by hand and tighten the screw using a flat head screw driver to lock the CPU in Place.
!!! Please make sure the golden cut edge location is aligned with the notch of the CPU socket. If
the CPU does not align with the CPU socket, it will damage the CPU!!!
Step 2: Installing CPU Heat Sink and Fan
2-1 Use the Heat Sink and Fan that is provided.
2-2 Slide the CPU Heat Sink into position over the CPU.
!!! Be sure that there are no wires underneath the Heat Sink. !!!
2-3a.b.c.d.e. Align the five screws with the screw holes next to the CPU. You may need to slide the Heat
Sink to the side to align. Tighten the five screws in a numerical order.
!!! Improper connection of the CPU heat sink will damage the notebook and CPU!!!
2-6 After making sure that all screws are tight, connect the CPU Fan.
!!! Connect the wires correctly. There is only one way to connect. DO NOT force in. !!!
!!! Warning: failure to connect the fan may cause damage to the CPU or the notebook!!!
Step 3: Installing Notebook Memory
3-1 Align the memory module to the DIMM socket 1.
!!! Memory module can only fit in one direction due to the keyed notch. Wrong orientation will
cause improper installation and may damage the memory modules or DIMM sockets!!!
3-2 Push down the memory module gently until the metal-locking levers aside from the DIMM socket 1 is
fastened.
3-3 If you have more than one memory module, please repeat steps 3-1 and 3-2.
!!! Memory module can only fit in one direction due to the keyed notch. Wrong orientation will
cause improper installation and may damage the memory modules or DIMM sockets!!!
3-4a.b.c.d.e.f. After installing the CPU and Memory, gently snap the cover until it locks into position. Lock
down the cover by applying 4 screws.
Step 5: Installing Notebook Hard Drive (HDD)
5-1a. Please use the given HDD shielding tray.
!!! Hard Drive may not be included !!!
5-2 Insert the HDD into the given HDD shielding tray.
!!! Improper alignment will cause damage to the HDD and the Notebook!!!
5-3a.b. After inserting the shield over the HDD, fasten with the screws that are provided.
5-4a.b. After installing the shield, place the HDD into the HDD bay. Gently push the HDD towards the
side until HDD fits securely in place.
Dieses Handbuch passt für folgende Modelle
1
Andere MSI Laptop Handbücher
MSI
MSI PR400 Bedienungsanleitung
MSI
MSI A11MT-009IT Bedienungsanleitung
MSI
MSI MS-171F - Whitebook - 17 Bedienungsanleitung
MSI
MSI Gaming G Series Bedienungsanleitung
MSI
MSI WF66 11UI-268 Bedienungsanleitung
MSI
MSI 12HW-001 Bedienungsanleitung
MSI
MSI GL63 8SE-056IT Bedienungsanleitung
MSI
MSI Gaming GP65 Bedienungsanleitung
MSI
MSI WindPad Bedienungsanleitung
MSI
MSI GS63 Bedienungsanleitung
MSI
MSI Prestige 15 Bedienungsanleitung
MSI
MSI Stealth 14 Studio i7-13700H Bedienungsanleitung
MSI
MSI X320 Bedienungsanleitung
MSI
MSI Gaming GT75 Bedienungsanleitung
MSI
MSI FX600 Bedienungsanleitung
MSI
MSI E7405 Bedienungsanleitung
MSI
MSI GT735 Bedienungsanleitung
MSI
MSI 13VI-028US Bedienungsanleitung
MSI
MSI Summit E14 A11SCS-208FR Bedienungsanleitung
MSI
MSI B13M-271NL Bedienungsanleitung
