multicomp pro MP010703 Bedienungsanleitung
Page <2> V1.003/02/23
Newark.com/multicomp-pro
Farnell.com/multicomp-pro
sg.element14.com/b/multicomp-pro
Features
• Digital VHF&UHF indoor amplier (1 Input, 2 Output)
• SMD circuit technology design
• Easy to install and convenient to use
• High output capability with low noise
Specication Table
Input/Output Frequency Range Max. Gain Adjustable Gain Range Noise Figure Power Supply
1/2 47-862MHz 28dB 0-10dB <4dB DC 12V 200mA
Installation
Step 1: Establish a coaxial cable (the coaxial cable is not included in the package) connection between the antenna and the
input of the amplier.
Step 2: Establish a coaxial cable connection between the amplier and TV.
Step 3: Plug the amplier into the power adaptor.
Step 4: Check the LED indicate light is on, if not, please go back to step1-3 to ensure the amplier is well connected to the
adaptor.
Gain Adjusting
In order to adjust the amplier gain turn knob until to get the best signal reception:
- to increase gain, turn the knob clockwise
- to reduce gain, turn the knob anti clock wise
Remember that maximum amplication dose not necessarily correspond to optimum signal quality.
- The built-in adjustment dial on the power booster unit allows ease and exibility to increase or decrease the amplier
strength of antenna.
Page <3> V1.003/02/23
Newark.com/multicomp-pro
Farnell.com/multicomp-pro
sg.element14.com/b/multicomp-pro
Important Notice : This data sheet and its contents (the “Information”) belong to the members of the AVNET group of companies (the “Group”) or are licensed to it. No licence is granted for
the use of it other than for information purposes in connection with the products to which it relates. No licence of any intellectual property rights is granted. The Information is subject to change
without notice and replaces all data sheets previously supplied. The Information supplied is believed to be accurate but the Group assumes no responsibility for its accuracy or completeness,
any error in or omission from it or for any use made of it. Users of this data sheet should check for themselves the Information and the suitability of the products for their purpose and not make
any assumptions based on information included or omitted. Liability for loss or damage resulting from any reliance on the Information or use of it (including liability resulting from negligence or
where the Group was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict the Group’s liability for death or personal injury resulting from its
negligence. Multicomp Pro is the registered trademark of Premier Farnell Limited 2019.
Safety Instruction
Please read the safety information carefully before using this amplier.
Cleaning : Remove the power supply plug before clean the unit. Use a dry or slightly dampened cloth and
ensure that no moisture in the unit.
Objects in the unit : Make sure that no objects can get into the ventilation slots and openings. There is a risk to life
due to electric shock.
Repair : Repairs must be carried out only by the qualied specialist person. Never open the case of
the unit yourself. Even when disconnected from the mains, there is an acute risk to life due to
electric shock. Internal components may be damaged if couched.
Adequate Ventilation : The Ventilation slots of the unit must never be covered.
External Inuences : Never expose the unit to moisture (e.g. condensation or spray water) or direct sunlight. Do not
place the unit in the vicinity of heat sources, such as heaters and self-heating devices.
Mains Voltage : Use the equipment with the voltage specied on the case only. Do not plug the unit into the
mains until all connection and installation work has been completed!
Included in the package:
• Amplier main unit
• AC-DC Adapter
• 2×5ft coaxial cable
Inhaltsverzeichnis
Andere multicomp pro Verstärker Handbücher
