MULTIQUIP Standard Handle SXH Bedienungsanleitung

WALK-BEHIND TROWELS — HANDLE INSTALLATION INSTRUCTIONS P/N 20485 — REV. #4 (09/18/14) — PAGE 1

Walk-Behind Trowels

Handle/Throttle Assembly Installation

The following instructions are intended to assist the user in the installation of the Standard Handle (SXH/SXHD) and Quick

Pitch™ (QXH/QXHD) on the Multiquip walk-behind trowels. It is not intended to take the place of the Operation and Parts

Manual shipped with the trowel. Refer to the Operation and Parts Manual for SAFETY, OPERATION, and MAINTENANCE

Information. If you did not receive a manual with your trowel, contact Multiquip at (800) 421-1244 for a replacement.

REQUIRED TOOLS

Ratchet/Socket set

Wrench

Phillips Screwdriver

PARTS

Verify that all parts are accounted for. See Figure 1 and

Table 1.

Figure 1. Standard/Quick PitchTM Trowel Handle

STANDARD

HANDLE

QUICK PITCH™

HANDLE

INSTRUCTIONS

WORK SAFELY!

Only a qualiﬁed service technician with proper training

should perform this installation. Follow all shop safety rules

when performing this installation.

PREPARATION

1. Make sure trowel is turned off and engine is cool.

2. Place the trowel in an area free of dirt and debris. Make

sure it is on secure level ground.

Table 1. Handle Parts

Item

No. Part No. Description Qty. Remarks

1SXH

or QXH

Standard Handle

or Quick-Pitch™ Handle 1Includes

item 2

2 22100 Handle Installation Kit 1 Includes

items 3-7

3 1493 3/8-16 x 3 1/4 HHC Screw 1

4 10133 3/8-16 Nyloc Nut 2

5 10136 3/8 Flat Washer 2

6 20485 Installation Instructions 1

7 21746 Spring, Primary Throttle Return 1

WALK-BEHIND TROWELS — HANDLE INSTALLATION INSTRUCTIONS P/N 20485 — REV. #4 (09/18/14) — PAGE 2

UNPACKING THE TROWE

This trowel is equipped with a folding upper handle (Figure 2).

The trowel is shipped with the handle in the folded or stowed

position.

1. To place the folding upper handle in the operational

position, simply turn the star wheel counterclockwise

to release it from its folded or stowed position.

2. Next, pull back on the upper handle and place handle in

the desired position. Turn star wheel clockwise to lock

handle in place. Make sure handle is locked ﬁrmly in

place so that the handle will not move or slip.

Figure 2. Unpacking the Trowel

FOLDED

POSITION

OPERATIONAL

POSITION

STAR WHEEL

UPPER

HANDLE

OPERATIONAL

POSITION

MAIN HANDLE TUBE INSTALLATION

1. Attach the main handle tube to the gearbox using the

supplied hardware as shown in Figure 3.

Figure 3. Handle Installation

2. The upper handle is already attached to the main

handle tube.

3. If readjustment is necessary, loosen the star wheel as

shown in Figure 4 and move the upper handle to the

desired position.

Figure 4. T-Handle Bar Adjustment

GEARBOX

3/8 FLAT

WASHER

3/8-16 X 3.25

HHC SCREW

MAIN HANDLE

(TUBE)

3/8-16

NYLOC NUT

T-HANDLE BAR

HEIGHT

ADJUSTMENT

STAR WHEEL

WALK-BEHIND TROWELS — HANDLE INSTALLATION INSTRUCTIONS P/N 20485 — REV. #4 (09/18/14) — PAGE 3

BLADE PITCH CABLE INSTALLATION

1. For trowels equipped with a Standard handle (SXHC),

simply turn the star wheel counterclockwise to pitch

the blades ﬂat.This will release the tension on the blade

pitch cable (Figure 5).

Figure 5. Adjusting Cable Blade

Pitch (Standard Handle)

2. For trowels equipped with a Quick Pitch™ T-handle

(QXHC), simply squeeze the trigger lock and push

the T-handle towards the engine to pitch the blades

downward. Pushing the T-handle towards the engine

will cause the blades to lay ﬂat (Figure 6). This will

release the tension on the blade pitch cable.

Figure 6. Adjusting Cable Blade Pitch

(Quick-PitchTM Handle)

INCREASE

BLADE PITCH

(CW)

DECREASE

BLADE PITCH

(CCW)

PITCH

FULL

PITCH

T-HANDLE

TRIGGER

LOCK

3. Remove brass set nut #1 from the blade pitch cable

end. See Figure 7.

Figure 7. Blade Pitch Cable

4. Thread the brass set nut #2 towards the cable as far

as possible. See Figure 7.

5. Insert the cable end through the yoke eyelet (Figure 8).

Tighten brass set nut #1 by hand to remove all the

slack from the cable.

Figure 8. Cable Yoke Attachment

6. Using a wrench, tighten the brass set nut #2 up against

the yoke boss. This will lock the cable in place.

7. Using a wrench, tighten the brass set nut #1 against

the yoke boss.

BLADE

PITCH

CABLE

BRASS

SET

NUT #1

BRASS SET

NUT #2

BLADE

PITCH

CABLE

YOKE

EYELET

BRASS SET

NUT #1 BRASS SET

NUT #2

WALK-BEHIND TROWELS — HANDLE INSTALLATION INSTRUCTIONS P/N 20485 — REV. #4 (09/18/14) — PAGE 4

THROTTLE CABLE INSTALLATION

Refer to Figure 9 for the location of components.

Figure 9. Throttle Cable Installation

1. Uncoil the throttle cable and housing.

2. Check that the throttle cable is fed through the tube on

the underside of the handle and secured to the upper

handle and main tube with the zip ties.

3. Place the throttle in the idle position.

4. Back off both the cable housing clamp screw and the

swivel stop screw.

5. Place the primary throttle return spring (P/N 21746)

between the cable housing clamp and the swivel stop

screw.

6. Feed the cable assembly through the cable housing

clamp, primary throttle return spring, and swivel stop

hole, until the cable housing extends under the housing

clamp to its far edge.

7. Ensure that the cable housing is seated in the throttle

cable receiver.Tighten the cable housing clamp screw.

8. Pull cable end with pliers to remove slack.

9. Tighten swivel stop screw to clamp cable.

CABLE

END

SWIVEL

STOP

SCREW

ADJUSTER

NUT

SWIVEL

STOP

HOLE

CABLE

HOUSING

CLAMP

SCREW

CABLE

HOUSING

CLAMP

PRIMARY

THROTTLE

RETURN

SPRING

CABLE

HOUSING

END

TROWEL

THROTTLE

CABLE

10. Adjust cable tension by loosening the lock nut on the

throttle cable receiver (see Figure 10), loosening or

tightening the adjusting nut below it, then retightening

the lock nut.

Figure 10. Adjusting Cable Tension

Centrifugal Stop Switch Connection

1. Connect the black tail wire from the engine to the top

black safety stop wire from the centrifugal stop switch

as shown in Figure 11.

Figure 11. Safety Stop Switch Connections

IDLE

RUN

THROTTLE

LEVER ADJUSTING

NUT (TOP)

LOCKING NUT

(BOTTOM)

NOTICE

If the throttle lever does not return to the "neutral"

position with throttle backed off, loosen adjusting nut

1/2 turn at a time, tighten and recheck. Readjust throttle

tension as necessary.

NOTICE

Safety stop switches are equipped with 2 wires.

Connect bottom BLACK/RED wire (Figure 11) directly

to engine ground.

OFF

CENTRIFUGAL

STOP SWITCH

BOTTOM

EXISTING

SCREW

FUEL TANK

TOP

BLACK/RED

ENGINE

GROUND

POINT

RECOIL

STARTER

COVER

MALE

FEMALE

BLACK BLACK

TAIL WIR

WALK-BEHIND TROWELS — HANDLE INSTALLATION INSTRUCTIONS P/N 20485 — REV. #4 (09/18/14) — PAGE 5

2. Using a 10MM socket, remove the existing bottom

mounting screw on the recoil starter cover (Figure 11)

and connect the bottom black/red wire from the

centrifugal stop switch to this engine ground point.

3. Reinstall mounting screw and tighten securely.

4. Check that the wires are secured to the main tube

with zip ties.

Your Local Dealer is:

HERE’S HOW TO GET HELP

PLEASE HAVE THE MODEL AND SERIAL

NUMBER ON-HAND WHEN CALLING

UNITED STATES

Multiquip Corporate Ofﬁce MQ Parts Department

18910 Wilmington Ave.

Carson, CA 90746

Contact: mq@multiquip.com

Tel. (800) 421-1244

Fax (310) 537-3927

800-427-1244

310-537-3700

Fax: 800-672-7877

Fax: 310-637-3284

Service Department Warranty Department

800-421-1244

310-537-3700

Fax: 310-537-4259 800-421-1244

310-537-3700

Fax: 310-943-2249

Technical Assistance

800-478-1244 Fax: 310-943-2238

CANADA UNITED KINGDOM

Multiquip Multiquip (UK) Limited Head Ofﬁce

4110 Industriel Boul.

Laval, Quebec, Canada H7L 6V3

Contact: jmartin@multiquip.com

Tel: (450) 625-2244

Tel: (877) 963-4411

Fax: (450) 625-8664

Unit 2, Northpoint Industrial Estate,

Globe Lane,

Dukinﬁeld, Cheshire SK16 4UJ

Contact: sales@multiquip.co.uk

Tel: 0161 339 2223

Fax: 0161 339 3226

Multiquip Inc

and

the MQ logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks are the property

of their respective owners and used with permission.

The information and speciﬁcations included in this publication were in effect at the time of approval for printing. Illustrations, descriptions, references and technical data contained in

this document are for guidance only and may not be considered as binding. Multiquip Inc. reserves the right to discontinue or change speciﬁcations, design or the information published

in this publication at any time without notice and without incurring any obligations.

Walk-Behind Trowels

Handle/Throttle Assembly Installation

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere MULTIQUIP Kelle Handbücher

MULTIQUIP

MULTIQUIP PRO46 Leitfaden

MULTIQUIP

MULTIQUIP HPHA36C5H Leitfaden

MULTIQUIP

MULTIQUIP BH11C Betriebsanleitung

MULTIQUIP

MULTIQUIP HHX Bedienungsanleitung

MULTIQUIP

MULTIQUIP B Series Bedienungsanleitung

MULTIQUIP

MULTIQUIP J-36 Leitfaden

MULTIQUIP

MULTIQUIP BS90C Leitfaden

MULTIQUIP

MULTIQUIP J36E2 Leitfaden

MULTIQUIP

MULTIQUIP Whiteman HTXD6i Bedienungsanleitung

MULTIQUIP

MULTIQUIP Whiteman LD6SL Bedienungsanleitung

MULTIQUIP

MULTIQUIP CA4HM Bedienungsanleitung

MULTIQUIP

MULTIQUIP BH11C Betriebsanleitung

MULTIQUIP

MULTIQUIP hhn34tvdtcsl4 Bedienungsanleitung

MULTIQUIP

MULTIQUIP STOW STR46SPVG Leitfaden

MULTIQUIP

MULTIQUIP WHITEMAN CA5BM Bedienungsanleitung

MULTIQUIP

MULTIQUIP Whiteman series Bedienungsanleitung

MULTIQUIP

MULTIQUIP Whiteman Series Handbuch

MULTIQUIP

MULTIQUIP Whiteman HTN-28K-TCSL Bedienungsanleitung

MULTIQUIP

MULTIQUIP Whiteman CA5BC Bedienungsanleitung

MULTIQUIP

MULTIQUIP HHN-31V Leitfaden

MULTIQUIP

MULTIQUIP Whiteman J36H55 Bedienungsanleitung

MULTIQUIP

MULTIQUIP JH55C Leitfaden

MULTIQUIP

MULTIQUIP Whiteman series Bedienungsanleitung

MULTIQUIP

MULTIQUIP hhn34tvdtcsl5 Bedienungsanleitung

Beliebte Kelle Handbücher anderer Marken

allen

allen HP105 Anwendungshandbuch

Bartell

Bartell BM90 Bedienungsanleitung

Stone

Stone CF24E Bedienungsanleitung

allen

allen HDX750 Anwendungshandbuch

Norton

Norton MTA 36 Leitfaden

MBW

MBW F24 Bedienungsanleitung

MBW

MBW MK8-75 Bedienungsanleitung

Wacker Neuson

Wacker Neuson CT 36-400E Bedienungsanleitung

Atlas Copco

Atlas Copco BG 240 E Wartungs- und Serviceanleitung

MQ Multiquip

MQ Multiquip JS36/30H55DE Series Leitfaden

swepac

swepac TR 600P Bedienungsanleitung

allen

allen PRO436DF Leitfaden

Wacker Neuson

Wacker Neuson CT 36 Bedienungsanleitung

Marshalltown

Marshalltown Speed Striker STRIKE45-L Bedienungsanleitung

Wacker Neuson

Wacker Neuson CRT 48-31V Bedienungsanleitung

Northern Industrial

Northern Industrial tmt-36 Bedienerhandbuch

BOMAX

BOMAX BM-836H Bedienungsanleitung

ENAR

ENAR TIFON 908 Bedienungsanleitung