Multitech MultiVOIP MVP110 Bedienungsanleitung
100
Voice / Fax over IP Networks
Standalone Voice/IP Gateway
Model MVP110
H.323 Mode
Quick Start Guide
Quick Start Guide
82050950 Revision A
MultiVOIP 100 (Model MVP110)
This publication may not be reproduced, in whole or in part, without prior
expressed written permission from Multi-Tech Systems, Inc. All rights
reserved.
Copyright © 2001, by Multi-Tech Systems, Inc.
Multi-Tech Systems, Inc. makes no representations or warranties with
respect to the contents hereof and specifically disclaims any implied
warranties of merchantability or fitness for any particular purpose.
Furthermore, Multi-Tech Systems, Inc. reserves the right to revise this
publication and to make changes from time to time in the content hereof
without obligation of Multi-Tech Systems, Inc. to notify any person or
organization of such revisions or changes.
Record of Revisions
Revision Description
AInitial Release.
(06/06/01)
Patents
This Product is covered by one or more of the following U.S. Patent
Numbers: 5.682.386; 5.757.801; 6.151.333. Other Patents Pending.
TRADEMARK
Trademark of Multi-Tech Systems, Inc. is the Multi-Tech logo.
Windows and Netmeeting are registered trademarks of Microsoft.
Multi-Tech Systems, Inc.
2205 Woodale Drive
Mounds View, Minnesota 55112
(763) 785-3500 or (800) 328-9717
U.S. Fax 763-785-9874
Technical Support (800) 972-2439
http://www.multitech.com
iii
Contents
Introduction ................................................................................... 4
Related Documentation ................................................................. 5
Installing Your MVP110 ................................................................. 6
Installing and Configuring Your MVP110 ................................. 6
Deploying the VOIP Network .................................................. 7
Unpacking Your MultiVOIP ............................................................ 8
Safety Warnings ............................................................................ 8
Cabling Your MultiVOIP ................................................................. 9
Cabling Procedure .................................................................. 9
Installing Your MVP110 Software ................................................. 11
Configuring Your MultiVOIP......................................................... 15
Registering with a Gatekeeper Phone Directory ................... 23
Building a Proprietary Phonebook Directory ......................... 27
Configuring Your Slave MVP110s ......................................... 35
Deploying the VOIP Network....................................................... 45
Remote Site Administrator .................................................... 45
Limited Warranty ......................................................................... 47
Technical Support ........................................................................ 48
FCC Declaration .......................................................................... 49
MultiVOIP Quick Start Guide
4
Introduction
Welcome to Multi-Tech's stand-alone Voice/IP Gateway, the
MultiVOIP model MVP110. The MVP110 allows analog voice
and fax communication over an IP network. Multi-Tech’s voice/
fax gateway technology allows voice/fax communication to be
transmitted, with no additional expense, over your existing IP
network, which has traditionally been data-only. To access this
free voice and fax communication, all you have to do is
connect the MVP110 to your telephone equipment, and then to
your existing Internet connection. Once configured, the
MVP110 then allows voice and fax to travel down the same
path as your traditional data communications.
The MVP110 supports the H.323 standards-based protocol
enabling your MVP110 to communicate with other third-party
VOIP Gateways or other endpoints that support the H.323
protocol, such as Microsoft NetMeeting®. The H.323 standard
defines how endpoints make and receive calls, how endpoints
negotiate a common set of audio and data capabilities, and
how information is formatted and sent over the network. This
version of the software also supports communication with a
Multi-Tech MVPGK1 Gatekeeper or an optional 3rd party
H.323 Gatekeeper which, when enabled, maintains its own
phonebook database, pre-registers all endpoints, controls the
bandwidth, and handles all conferencing issues such as
transferring of calls.
Figure 1. MVP110
5
Introduction
The MVP110 has one FXS voice/fax channel, a 10 Mbps
Ethernet LAN interface, and a Command port for configuration.
System management is provided through the Command port
using bundled Windows®software which provides easy-to-use
configuration menus and comprehensive online Help.
Related Documentation
The MVP110 Quick Start Guide is intended to be used by
qualified systems administrators and network managers. This
Quick Start Guide provides the necessary information for a
qualified person to unpack, cable, load software, and configure
the unit for proper operation.
A detailed MVP110 User Guide is included on your system CD
and provides in-depth information on the features and
functionality of Multi-Tech’s MVP110.
The CD media is produced using Adobe AcrobatTM for viewing
and printing the user guide. To view or print your copy of a
user guide, load Acrobat ReaderTM onto your system from the
CD, or obtain it as a free download from Adobe’s Web site:
http://www.adobe.com
The MVP110 User Guide is also available from Multi-Tech’s
Web site:
http://www.multitech.com
Viewing and printing a user guide from the Web also requires
that you have the Acrobat Reader loaded on your system. To
select the MVP110 User Guide from the Multi-Tech Systems
home page, click Documents, then click MultiVOIP in the
product list, then click MultiVOIP Manuals. All MVP110
documents will be displayed at the bottom of the page and you
can choose User Guide (MVP110) to view or download the .pdf
file.
MultiVOIP Quick Start Guide
6
Installing Your MVP110
The basic steps of installing your MVP110 network involve
unpacking the units, connecting the cables, and configuring
the units using management software (MVP 110
Configuration). This process results in a fully functional Voice
Over IP network. A brief description is provided below with
detailed instructions provided later.
Installing and Configuring Your MVP110
The VOIP administrator must first install the MVP110 software
and then configure each MVP110 for its specific function.
During the configuration process, it’s important to note that the
Phone Directory Database is configured differently depending
on whether or not you have Gatekeeper support on your VOIP
network.
If your VOIP network supports an H.323 Gatekeeper, you
must register all H.323 endpoints with the Gatekeeper. The
procedure for doing this is explained in the section
“Registering with a Gatekeeper Phone Directory.”
If your VOIP network does not have Gatekeeper software or
the Gatekeeper software is not enabled, then you must build a
proprietary phonebook with a “Master” MultiVOIP and “Slave”
MultiVOIPs. The “Master” unit includes the assignment of a
unique LAN IP address, subnet mask, and Gateway IP
address. Once all connections have been made, the VOIP
administrator configures the unit and builds the Phone
Directory Database that will reside in the Master unit.
After the “Master” MultiVOIP is configured, the administrator
moves on to configure the MultiVOIPs designated as “Slave”
units. Again, unique LAN IP addresses, subnet masks, and
Gateway IP addresses are assigned, and the Voice/Fax
channel is configured for the FXS Loop interface type. When
this is done, the Phone Directory Database option is set to
Slave, and the IP address of the Master MVP 110 is entered.
7
Introduction
Once all Slave units are configured, the process moves on to
the “Deploying the VOIP Network” section.
Deploying the VOIP Network
The final phase of the installation is deployment of the
network. When the remote MultiVOIPs are sent to their remote
sites, the remote site administrators need only connect the
units to their LAN and telephone equipment. A full Phone
Directory Database Proprietary Phonebook, supplied by the
Master MultiVOIP will be loaded into their units within minutes
of being connected and powered up.
For remote VOIPs that were configured with the Gatekeeper
option enabled, each MultiVOIP will be registered with the
Gatekeeper. The Gatekeeper phonebook directory is NOT
downloaded to the remote units.
MultiVOIP Quick Start Guide
8
Unpacking Your MultiVOIP
Remove all items from the box. (See Figure 2.)
MADE IN U.S.A
MADE IN U.S.A
www.multitech.com
Voice/Fax over IP Networks
Figure 2. Unpacking
Safety Warnings
Caution: Danger of explosion if battery is incorrectly replaced.
A lithium battery on the circuit board provides backup power
for the time keeping capability. The battery has an estimated
life expectancy of ten years.
When the battery starts to weaken, the date and time may be
incorrect. If the battery fails, the board must be sent back to
Multi-Tech Systems for battery replacement.
The FXS and Ethernet ports are not designed to be connected
to a Public Telecommunication Network.
9
Cabling
Cabling Your MultiVOIP
Cabling your MultiVOIP involves making the proper Power,
Command Port, and Ethernet connections. Figure 6 shows the
back panel connectors and the associated cable connections.
The Cabling Procedure section provides step-by-step
instructions for cabling your MultiVOIP.
Cabling Procedure
1. Using the supplied cable, connect the power supply to a
live AC outlet, then plug the power supply into the MVP
110 as shown in Figure 3.
Network Connection
Power Connection
Command Port Connection
FXS
Hub
Figure 3. Cable Connections
2. Connect the MVP 110 to a PC using the RJ-45 to DB9
(female) cable provided with your unit. Plug the RJ-45 end
of the cable into the Command port of the MVP 110 and
connect the other end to the PC’s serial port (Figure 3).
3. Connect a network cable to the Ethernet 10Base-T
connector on the back of the MVP 110. Connect the other
end of the cable to your network.
4. If you are connecting a station device such as an analog
telephone, fax machine, or Key Telephone System (KTS)
MultiVOIP Quick Start Guide
10
to your MVP 110, connect an RJ-11cable to the Voice/Fax
Channel connector on the back of the MVP 110 and the
other end to the station device.
5. Turn on power to the MVP 110 by setting the power switch
on the right side to the On position. Wait for the Boot LED
on the MVP 110 to go off before proceeding. This may
take a couple of minutes.
Inhaltsverzeichnis
Andere Multitech Tor Handbücher
Multitech
Multitech MultiVOIP 400 MVP400 Bedienungsanleitung
Multitech
Multitech MultiVOIP MVP200 Bedienungsanleitung
Multitech
Multitech MultiVOIP MVP2400 Bedienungsanleitung
Multitech
Multitech MultiVOIP MVPFX2-8 Bedienungsanleitung
Multitech
Multitech Conduit MTCDT-L4E1 Montageanleitung
Multitech
Multitech RouteFinder RF550VPN Bedienungsanleitung
Multitech
Multitech 410 Bedienungsanleitung
Multitech
Multitech OneBox Smart Building Bedienungsanleitung
Multitech
Multitech MULTIVOIP MVP-210 Bedienungsanleitung
Multitech
Multitech MultiVOIP MVPFX2-2 Bedienungsanleitung
Multitech
Multitech MultiConnect Conduit Bedienungsanleitung
Multitech
Multitech MultiVOIP 100 (MVP110 Bedienungsanleitung
Multitech
Multitech MULTIVOIP MVP-210 Bedienungsanleitung
Multitech
Multitech Conduit 300 Series Montageanleitung
Multitech
Multitech ProxyServer MTPSR2-201 Bedienungsanleitung
Multitech
Multitech MultiVOIP MVP 800 Bedienungsanleitung
Multitech
Multitech MVP-2410, MVP-3010 Bedienungsanleitung
Multitech
Multitech MultiConnect Conduit AP MTCAP-LNA3-915 Bedienungsanleitung
Multitech
Multitech MultiVOIP MVP2400 Bedienungsanleitung
Multitech
Multitech MultiVOIP 100 MVP120 Bedienungsanleitung
Beliebte Tor Handbücher anderer Marken
LST
LST M500RFE-AS Bedienungsanleitung
Kinnex
Kinnex Media Gateway Bedienungsanleitung
2N Telekomunikace
2N Telekomunikace 2N StarGate Bedienungsanleitung
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung
Telsey
Telsey CPVA 500 - SIP Bedienungsanleitung
