Multitech QuickCarrier USB-D Bedienungsanleitung
Omniguard MultiTech QuickCarrier USB-D User’s Guide
Summary
This guide is for using your Omniguard with the MultiTech QuickCarrier USB-D
wireless modem to send and receive text messages. This modem only works with
Omniguard Cellular units with serial numbers C501000-C503799 and firmware V9.4b1
or later.
How It Works
Connecting a wireless modem to the Omniguard allows it to send and receive text
messages just like a regular wireless phone. The Omniguard can be configured to send
alarm notices and daily status reports to up to two wireless phones. In addition it can
respond to request for information from wireless phones and via email. If the Omniguard
is programmed using a PC, it is also possible to send alarm and/or daily status reports to
additional wireless phones and email addresses.
The Wireless Modem
The MultiTech QuickCarrier USB-D wireless modem only works with Omniguard
Cellular units with serial numbers C501000-C503799 and firmware V9.4b1 or later. If
you do not have the latest firmware download Omniguard Communications from the
Engineering Solutions web site to update.
In order to use the modem you will need to acquire a SIM card from a wireless
provider. The SIM card contains the phone number and connection information for
providers. The modem supports Verizon as well as wireless carriers using GSM such as
AT&T and T-Mobile.
You have two options for setting up an account. You can establish a conventional
wireless contract where you are billed for monthly service. You may be able to set up
this type of account without even getting a phone, only a SIM card. If you must get a
phone, the SIM card can easily be removed and installed in the modem. Choose a
wireless plan that is best for the number of text messages you plan to send and receive
from the Omniguard. You will not need any regular calling minutes since the modem
will not make conventional phone calls.
Your second option is to use a prepaid wireless plan. Most providers offer plans with
no contracts that allow text messaging. This is a good option if the number of messages
will not be too high. You must monitor your account balance using online tools to make
sure you do not run out during a job. Keep in mind that if you’ve set up the Omniguard
to send text messages each time there is an alarm, you could send up to 576 messages per
day.
Connecting
Follow the instructions in the Quick Start Guide included with the modem to insert
the SIM card in the modem.
Turn your Omniguard Cellular on and wait until the pressure is displayed. Touch the
wireless icon in the lower right corner of the screen above the time. It may be showing a
wireless tower with or without a question mark or exclamation mark or it may just be a
question mark. Proceed to the setup cell screen and turn the “Cell Modem” or “Network”
to “Off”. Press the return/exit button to return to the main screen.
Plug your modem into the Omniguard’s USB port and wait. It can take a few minutes
for the Omniguard to recognize the modem. The wireless icon in the lower right should
change from a tower with an “X” across it to a tower with or without a question mark.
Touch the icon and proceed to the setup screen. Set the “Cell Service Provider” to
“Verizon” if you are using a Verizon SIM or “Other” if you are using any other provider.
Press the return/exit button to return to the main screen. If the provider needs to be
changed in the modem you will see a warning. Press the “Start” button to change the
modem to match the SIM being used.
Authorizing
If you did not purchase your modem directly from Engineering Solutions it will need
to be authorized for use by the Omniguard. When your modem is connected and the
Omniguard is turned on, you will be informed that the modem is “Not Authorized” along
with a serial number. Contact Engineering Solutions, provide us with the serial number
shown on the screen and we will give the passcode to authorize the modem. To enter the
passcode into the Omniguard use the up and down arrow keys to change a digit and the
right and left arrow keys to move between the digits. When all the digits have been
entered press SAVE to authorize the modem. You will get the message “Modem ready”.
The modem will now work with any compatible Omniguard.
Configuring
Touch the wireless icon in the lower right corner of the screen above the time. On the
cell setup screen two wireless phone numbers can be programmed directly into the
Omniguard. A text message will be sent to each phone number when the Omniguard
enters normal operation and when an alarm condition occurs. The minimum time
between alarm text messages is limited to the Message Rate to prevent frequent messages
if the unit is going in and out of the alarm state.
Normal Operation Message
JOB:
1234 Jacksonville Ave N
NORMAL OP 12:59:16
Reply with 0 for menu.
Omniguard 4
# G400000
Alarm Message
>> ALARM <<
JOB:
1234 Jacksonville Ave N
ALARM 1: +0.010" WC
12:59:07 +0.011" WC
Reply with 0 for menu.
Omniguard 4
# G400000
Phone numbers programmed directly into the Omniguard will also receive a daily
summary indicating how long the unit was in normal operation, the number of alarms and
the total time the unit was in the alarm state. The summary report will be sent at 5:30pm
each day unless a Notify List has been selected (see below).
Daily Summary Message
DAILY SUMMARY
JOB:
1234 Jacksonville Ave N
IN NORMAL OP:
6hr 46min
ALARMS:
12
IN ALARM:
59min 12sec
Reply with 0 for menu.
Omniguard 4
# G400000
In order to support more wireless phone numbers, the Omniguard can store up to four
Notify Lists. These lists allow different phone numbers for alarm and normal operation
notification and reports. They also allow the report time to be changed. Notify Lists can
only be created and programmed into the Omniguard using the Omniguard
Communications PC software available at www.engsolinc.com. See the help that comes
with the software for more information on setting up Notify Lists.
Note that while the software allows email addresses in the Notify Lists, they are not
supported by the Omniguard when using the MultiTech QuickCarrier USB-D modem.
To configure and test the wireless modem –
1. Connect the modem to the Omniguard as described above.
2. Highlight WIRELESS MODEM using up and down keys and press SELECT to
view or change the settings.
3. If desired, press up and down keys to change Cell # 1, the first of two wireless
phone numbers that can be programmed on the Omniguard. Once the first digit of
the number has been changed, use right and left keys to move to the other digits.
To delete the phone number, set the first digit to a blank.
4. Press right and left keys to move to Cell # 2. Again use up and down keys to
change the first digit of the phone number. Once the first digit of the number has
been changed, use right and left keys to move to the other digits.
5. Press right and left keys to move to Notify. If you have programmed one or more
Notify Lists into the Omniguard using the Omniguard Communications PC
software, you can select on of them using “up/down”.
6. Press right and left keys to move to Test Modem. When “Test” is selected,
pressing the SELECT key will cause a message to be sent to the Cell # 1 and Cell
# 2 phone numbers as well as any numbers in the chosen Notify List.
7. Press SAVE to save the settings and return to the Main Menu.
Pressing the EXIT key will return you to the Main Menu without saving the updated
settings.
Requesting Information
It is also possible to request information from an Omniguard connected to a wireless
modem. A text message or email is sent to the Omniguard which will reply with a report
based on the content of the message. The reports include a daily summary, overall job
summary, current status and settings. To get a complete list of reports the Omniguard can
provide send a text message or email with a “0” (zero) in the body of the message.
Text messages sent to the Omniguard must be in the “short message” format and are
sent to the phone number of the wireless modem.
Sample replies…
Menu- “0” or unknown message
Reply with 1, 2, 3 or 4 to get report:
1-Current Status
2-Daily Summary
3-Entire Job
4-Settings
Omniguard 4
# G400000
Status- “1”
JOB:
1234 Jacksonville Ave N
STATUS:
Waiting Pressure
PRESSURE:
0.000" WC
Omniguard 4
# G400000
Daily Summary- “2”
DAILY SUMMARY
JOB:
1234 Jacksonville Ave N
IN NORMAL OP:
6hr 46min
ALARMS:
12
IN ALARM:
59min 12sec
Reply with 0 for menu.
Omniguard 4
# G400000
Job Summary-“3”
JOB SUMMARY
JOB:
1234 Jacksonville Ave N
START:
02-01-09 8:00
IN NORMAL OP:
23hr 46min
ALARMS:
12
IN ALARM:
59min 12sec
Omniguard 4
# G400000
Settings-“4”
SETTINGS
MEM EST DAYS LEFT:
100
DATE & TIME:
01-01 12:00
ALARM 1:
-0.025" WC
ALARM 2:
-0.050" WC
PRINTER: Off
Omniguard 4
# G400000
Tips
•It is very helpful to make use of the Job capabilities of the Omniguard
including the use of Job Names. When starting work at a new job site, touch
“START JOB” at the bottom of the main screen on the Omniguard and enter a
meaningful name for the job, such as the address. If “WAITING FOR
PRESSURE” or some other message is displayed at the bottom of the screen,
touch it to end the current job and then start a new one. This will make the
reports easier to identify since they all use the Job Name. The Job Summary
will also accurately reflect work done.
Andere Handbücher für QuickCarrier USB-D
1
Inhaltsverzeichnis
Andere Multitech Modem Handbücher
Multitech
Multitech MultiModem MT5634ZPX-PCI-U Bedienungsanleitung
Multitech
Multitech MT9234ZBA-USB Bedienungsanleitung
Multitech
Multitech MultiModem MTCBA-G-F4 Bedienungsanleitung
Multitech
Multitech MTD100U Bedienungsanleitung
Multitech
Multitech MultiModemISDN MTA128ST-USB Bedienungsanleitung
Multitech
Multitech MT5656ZDX Series Bedienungsanleitung
Multitech
Multitech MultiModem MT9234ZPX-UPCI Bedienungsanleitung
Multitech
Multitech MTE-LAT6-B07 Bedienungsanleitung
Multitech
Multitech MT5634ZPX-PCI Bedienungsanleitung
Multitech
Multitech MessageSaver MT5634MSV Bedienungsanleitung
Multitech
Multitech MultiModem MT5634ZPX-V.92-ISA Bedienungsanleitung
Multitech
Multitech MultMobile MT9234MU Bedienungsanleitung
Multitech
Multitech MultiModem MT3334ZDX Bedienungsanleitung
Multitech
Multitech MT1932ZDX Bedienungsanleitung
Multitech
Multitech MTCBA-C-U-N1 Bedienungsanleitung
Multitech
Multitech MultiModem MT2834MR6 Bedienungsanleitung
Multitech
Multitech MultiModem GPRS with Ethernet Interface Bedienungsanleitung
Multitech
Multitech MultiModem ZBA MT9234ZBA Bedienungsanleitung
Multitech
Multitech MultiModem MT5634ZBA-V-V92 Bedienungsanleitung
Multitech
Multitech IWay MTA128ST Bedienungsanleitung
Beliebte Modem Handbücher anderer Marken
Davicom
Davicom DM562AP Bedienungsanleitung
EpiValley
EpiValley TATA indicom SXC-1080 Bedienungsanleitung
Zte
Zte WiMAX Bedienungsanleitung
Intelimax
Intelimax MA-2060 Bedienungsanleitung
SMC Networks
SMC Networks D3CM1604V Gebrauchs- und Pflegehandbuch
Telstra
Telstra Wi-Fi 4G Advanced Pro X Bedienungsanleitung
US Robotics
US Robotics 3453C Bedienungsanleitung
MaxTech
MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Bedienungsanleitung
Zte
Zte MF823 Bedienungsanleitung
Four-Faith
Four-Faith F1403 Bedienungsanleitung
Sierra Wireless
Sierra Wireless AIRLINK MP595W Bedienungsanleitung
Gemtek
Gemtek WiMAX WIXFBR-103 Bedienungsanleitung