Munters Horizon Series Bedienungsanleitung
1© Munters Corporation, August 2022 QM1217r0
Instruction Manual
Horizon Series
CSI24 Continuous Sidewall Inlet
Models: CSI24100SF • CSI2410SF • CSI24100CF •
CSI2410CF
HORIZON
CSI24
Continuous
Sidewall Inlet -
Flush Mount
CSI24 Continuous Sidwall Inlet - Straight Rack
Room Side View
CSI24 Continuous Sidwall Inlet - Straight Rack
Outside/Hallway Side View
© Munters Corporation, August 2022
2QM1217r0
CSI24 Continuous Sidewall Inlet
Instructions for Use and Maintenance
Thank You:
Thank you for purchasing a Munters CSI24 Continuous Sidwall Inlet. Munters equipment is designed to be the
highest performing, highest quality equipment you can buy. With the proper installation and maintenance it will
provide many years of service.
Please Note:
To achieve maximum performance and insure long life from your Munters product it is essential that it be
installed and maintained properly. Please read all instructions carefully before beginning installation.
Warranty:
For Warranty claims information see the “Warranty Claims and Return Policy” form QM1021 available from the
Conditions and Limitations:
• Products and Systems involved in a warranty claim under the “Warranty Claims and Return Policy” shall have
been properly installed, maintained and operated under competent supervision, according to the instructions
provided by Munters Corporation.
• Malfunction or failure resulting from misuse, abuse, negligence, alteration, accident or lack of proper
installation or maintenance shall not be considered a defect under the Warranty.
3 Munters Corporation, August 2022 QM1217r0
Index
Chapters Page
1. Unpacking the Equipment 4
1.1 Catalog Number Defi nition 4
1.2 Parts List 4-6
2. Installation Instructions 7
2.1 Framing 7
2.2 Foam Seal 8
2.3 Door Assembly 9
2.4 Left Door Assembly 9
2.5 Middle Door Assembly 12
2.6 Right Door Assembly 14
2.7 Door Installation 17
2.8 Drive Frame Installation 22
2.9 Actuator Installation 26
2.10 Drive Pipe Preperation 26
2.11 Drive Pipe Installation 27
3. Maintenance 33
© Munters Corporation, August 2022
4QM1217r0
4
3
2
1
5
1.1 System Description
Unpacking the Equipment 1.
Before beginning installation, check the overall condition of the equipment. Remove packing materials, and examine all
components for signs of shipping damage. Any shipping damage is the customer’s responsibility and should be reported
immediately to your freight carrier.
The Munters CSI24 Continuous Sidewall Inlet is a 24"H. door that can be continuous for a total of 150'L. and can be
mounted flush to the wall or offset so the drive pipe can be mounted away from the wall to avoid columns or posts. It
can also use either Straight Racks or Curved Racks. The CSI24 Continuous Sidewall Inlet is sold in 100' Door Kits and
10' Door Kits, an Ending Kit and the Actuator (actuator sold separately). For example: For a system that is 450'L.
with Offset Mount and Straight Racks, operated by 3 Actuators, the customer would receive the following:
(4) CSI24100SF, (5) CSI2410SF, (3) AC2872 and (3) Actuators (actuator sold separately).
Catalog Number Definition:
1.2 Parts List
CSI 24 100 S F
Mounting Type; O = Offset, F = Flush
Style of Rack; S = Straight, C = Curved
Length of Kit; 100 = 100 ft, 10 = 10 ft
Height of Door; 24"
Door Kits Ending Kits
AC2871 = Straight Offset Mount Ending Kit
AC2872 = Straight Flush Mount Ending Kit
AC2873 = Curved Offset Mount Ending Kit
AC2874 = Curved Flush Mount Ending Kit
Each 10'L. CSI24 Door Kit, CSI24Includes:
CSI2410
ID Cat. No. Qty. Description
[1] AC3470 1 Door w/ Hinge, 24"H. x 10'L. x 1.5"T., Blk/Wht, CSI24
[2] AC3440 1 Door Edge Trim, 120"L., GZ
[3] AC1415 1 1" SCHD10 (1.32"O.D.) Pipe x 126"L., SOE, 12GA, GZ
[4] KA2156 2 Foam Seal, P-Shape w/ TAB, 2.14"W. x 1.31"H. x 60"L., BLK
[5] AC3726 1 Straight Rack, 49"Travel, 57"(1450mm) L., GZ
AC3737 1 Curved Rack, 49"Travel, 57"(1450mm) L., GZ
CSI2410 Door Kit
5 Munters Corporation, August 2022 QM1217r0
11
10
12
13
6
8
9
7
1.2 Parts (continued)
Unpacking the EquipmentChapter 1
10'L. CSI24 Door Kit (continued)
CSI2410
ID Cat. No. Qty. Description
[6] AC3441 1 Flat Joiner Plate, 12"L., GZ
[7] AC3720 1 Pinion Gear for 1" Pipe, AL
[8] AC3708 1 Housing Rack Pinion Gear, PL
[9] AC3722 1 Pivoting Connector, Rack to Door, AL
[A] KP1257 1 Clevis Pin, ¼ "D x 2"L., ZP
[B] KP1105 1 Hairpin Cotter Pin, 0.59"D x 1.13"L., SS
[C] KS2808 2 M8-1.0, INT-HX, Set Screw, KNRL-CUP, ZP
[D] KS1064 2 3⁄8”-16 x 2.25” Hex Bolt, ZP
[E] KN1717 6 1⁄4”-20 Hex Flange Nylock Nut, SS
[F] KS1513 6 1⁄4”-20 x 2.25” Carriage Bolt, ZP
[G] KN1709 2 3⁄8”-16 Nylock Nut, ZP
[H] KS2282 64 #10-16 x ³⁄₄” HXWSR TEK Screw, SS
[J] KS1402 64 #9-15 x 1½ ” Seal Washer Polebarn Screw, ZP
[K] KS2463 2 1⁄4” x 1½ ” Lag Screw, ZP
[L] KS1080 2 3⁄8”-16 x 1” Hex Bolt, ZP
[M] KW3036 6 3⁄8” Flat Washer, USS, ZP
[10] AC3407 1 Inside Door Support, 24", GZ
[11] AC3417 1 Outside Door Support, 24", GZ
[12] AC3410 2 Rack Mounting Plate, GZ
[13] AC3704
1
Guide Plate w/BRNZ Bushing, 1" Pipe, L, GZ
[A]
[B]
[C]
[D]
[E]
[F]
[G]
[H]
[J]
[K]
© Munters Corporation, August 2022
6QM1217r0
7
9
15
4
16
13
8
5
12
Unpacking the EquipmentChapter 1
1.2 Parts (continued)
Each AC2872 Ending Kit, Flush, Straight Rack Includes:
ID Cat. No. Qty. Description
[4] KA2156 1 Foam Seal, P-Shape w/ TAB, 2.14"W. x 1.31"H. x 60"L., BLK
[5] AC3726 1 Straight Rack, 49"Travel, 57"(1450mm) L., GZ
AC3737 1 Curved Rack, 49"Travel, 57"(1450mm) L., GZ
[7] AC3722 1 Pivoting Connector, Rack to Door, AL
[8] AC3708 1 Housing Rack Pinion Gear, PL
[9] AC3720 1 Pinion Gear for 1" Pipe, AL
[12] AC3710 2 Rack Mounting Plate, GZ
[13] AC3704 1 Guide Plate w/BRNZ Bushing, 1" Pipe, L, GZ
[15] AC3484 2 Door End Trim, 24"L., CSI24, GZ
[16] AC3706 1 Straight Coupling, Actuator to 1" Pipe, 3.5" to CL, GZ
[A] KP1257 1 Clevis Pin, ¼"D x 2"L., ZP
[B] KP1105 1 Hairpin Cotter Pin, 0.59"D x 1.13"L., SS
[C] KS2808 2 M8-1.0, INT-HX, Set Screw, KNRL-CUP, ZP
[D] KS1064 3 3⁄8”-16 x 2.25” Hex Bolt, ZP
[E] KN1717 13 1⁄4”-20 Hex Flange Nylock Nut, SS
[F] KS1513 6 1⁄4”-20 x 2.25” Carriage Bolt, ZP
[G] KN1709 3 3⁄8”-16 Nylock Nut, ZP
[H] KS2282 20 #10-16 x ³⁄₄” HXWSR TEK Screw, SS
[K] KS2463 2 1⁄4” x 1½” Lag Screw, ZP
[L] KS2466 4 3⁄8” x 2” Lag Screw, ZP
[A]
[B]
[C]
[D]
[E]
[F]
[G]
[H]
[K]
[L]
7 Munters Corporation, August 2022 QM1217r0
Installation Instructions 2.
2.1 Framing
Figure 1A
Chart A
Catalog No. Length Height
Example Door Length (--)4" Door Height (--)2”
(1) CSI24100SF & (5) CSI2410SF
(150'L. x 24"H.) 149'-8" 22"
Step 1A
The CS2410SF was designed for the door to be installed in the room and the Actuator and Pipe Drive system
be mounted in the hallway. Construct the framed opening to correct size according to Chart A (below) and
your CSI24 Continuous Sidewall Inlet size. See Chart A. If installing 2 or more sections of CSI24 doors,
be sure to leave 24" minimum between each framed opening.
See Figure 1A
. Use Treated 2x6's for the
Framing.
Door Length --4"
22"
2x6 Treated
Figure 1B
HALLWAY SIDE
Wall Material
10'-0" O.C.
2x4 Treated
Step 1B
On the hallway side of the framing, install a treated 2x4, 18" from the end framing and then every 10'-0"
O.C. down the length of the framing with the last 2x4 being 18" from the opposite end framing. These 2x4's
should span the top and bottom framing. Also, install double treated 2x6's on the end of the framed opening
to be used to moun the LA actuator to.
See Figure 1B
.
18"
24"
2"
Double 2x6 Treated
2x6 Treated
© Munters Corporation, August 2022
8QM1217r0
Installation InstructionsChapter 2
Step 2
After the Framed Openings are completed, make sure the surface of the 2x lumber is clean and free from
debris. The P-Shaped Foam Seal [4], comes in 60" lengths. Starting at 2" from the inside edge of the End
Framing, so that it will overlap the side Foam Seal, peal the back from the adhesive on the back of the Foam
Seal and affix to the framing with the top of the "P" flush with the top of the framing. See Figure 2A and 2B.
For the Foam Seal on the End Framing, the top of the "P" should be flush with the inside edge of the framing
and should run from the inside edge of the Top Framing to the bottom of the Foam Seal on the next frame
member. See Figure 2A and 2B.
Step 3
Continue attaching the P-Shaped Foam Seal until there is Foam Seal attached to 3 sides of each Framed
Opening. Once the Foam Seal is completely attached, go back and permanently attach to the framing
using Staples or Nails in the nailing grove of the Foam Seal Flap. Staples or Nails are not provided and
should be spaced every 4" -- 6". See Figure 2A and 2B.
2.2 Foam Seal
Staple or Nail
(not provided)
Figure 2A
Figure 2B
Framing
P-Shaped Foam Seal [4]
P-Shaped Foam Seal [4]
P-Shaped Foam Seal [4]
2x4 Framing
9 Munters Corporation, August 2022 QM1217r0
Installation InstructionsChapter 2
Step 4
Each CSI24 Inlet system that is 30'L. or longer consists of (1) Left Door, (1 or more) Middle Doors and
(1) Right Door. The number of Middle Doors depends on the length of the run of CSI24 Doors. For example,
if the run of CSI24 Doors is 40'L. then there is (1) Left Door, (2) Middle Doors and (1) Right Door. If the run
is 100'L. then there is (1) Left Door, (8) Middle Doors and (1) Right Door. In the next steps all the doors will
be assembled before installing them to the framed openings. See Figure 3. If the run is only 20'L. then there
is only the Left Door and the Right Door.
Figure 3
View from Hallway/Hinge Side
TEK Screw [H]
TEK Screw [H] location
for Left End Door
Door Edge Trim [2]
Figure 4
Do not use
this hole at
this time.
2.3 Door Assembly
Step 5
Slide Door Edge Trim [2] onto the bottom edge of the CSI24 Door [1] and secure it with (14) TEK Screws [H]
through the (6) single holes in the middle area of the Door Edge Trim and the left most hole. See Figure 4.
Middle Door
Right Door
Left Door
2.4 Left Door Assembly
NOTE: The Left and Right ends of the system are
determined from the Hallway/Actuator side of
the inlet, with the inlet mounted in the room.
CSI24 Door with Hinge [1]
© Munters Corporation, August 2022
10 QM1217r0
Installation InstructionsChapter 2
Step 6
Slide a Door End Trim [15] over the Left Door and secure in place with (8) TEK Screws [H]. See Figure 5.
Figure 5
TEK Screw [H]
Door End Trim [15]
Step 7
For the Left Door, attach a Rack Mounting Plate [12] on each side of the door to the left pair of holes in the
Door Edge Trim using (2) TEK Screws [H] per Plate. See Figure 6. Then attach an Outside Door Support [11]
(24") at the right end of the CSI24 Door, on the room side, so that half of the Support is on the Door and the
other half of the Support hangs off the end. See Figure 6.
Figure 6
Rack Mounting Plate [12]
Left Pair of Holes
TEK Screw [H]
CSI24 Door with Hinge
Outside Door
Support [11]
CSI24 Door with Hinge
TEK Screw [H]
Room Side shown
for clarity
Dieses Handbuch passt für folgende Modelle
5
Inhaltsverzeichnis
Andere Munters Lüfter Handbücher
Munters
Munters AT16FPT Bedienungsanleitung
Munters
Munters GB Series Bedienungsanleitung
Munters
Munters CX24 Bedienungsanleitung
Munters
Munters WF54 T CP Series Bedienungsanleitung
Munters
Munters WM36 K CB Series Bedienungsanleitung
Munters
Munters EDC GHp Series Gebrauchsanweisung
Munters
Munters WM54K Bedienungsanleitung
Munters
Munters EC52 Bedienungsanleitung
Munters
Munters VX Series Bedienungsanleitung
Munters
Munters CX Series Bedienungsanleitung
Munters
Munters AT14F Bedienungsanleitung
Munters
Munters TU600 Gebrauchsanweisung
Munters
Munters EDHE Series Gebrauchsanweisung
Munters
Munters EM50 Gebrauchsanweisung
Munters
Munters EM52 Gebrauchsanweisung
Munters
Munters Breeze Fan Gebrauchsanweisung
Munters
Munters MFS36 Gebrauchsanweisung
Munters
Munters WM54 Gebrauchsanweisung
Munters
Munters AX Series Bedienungsanleitung
Munters
Munters EC52 Gebrauchsanweisung
