Murata WSN802G Kurzanleitung zur Einrichtung

Revision History

Revision

Date

Author

Change Description

06/18/2012

F. Perkins

Initial issue

01/27/2015

R. Willett

Reformatted to comply with new Murata V.I.

RFM products are now

Murata products.

WSN802G

802.11g

Wireless Sensor

Network Module

Integration Guide

WSN802G Rev. 2.0 01-27-15 www.murata.com

Important Regulatory Information

RFM Product FCC ID: HSW-WSN802G

IC 4492A-WSN802G

Note: This unit has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with the in-

struction manual, may cause harmful interference to radio communications. Operation of this equipment

in a residential area is likely to cause harmful interference in which case the user will be required to cor-

rect the interference at their expense.

The WSN802G has been designed to operate with any dipole antenna of up to 9 dBi of gain, or any patch

antenna of up to 12 dBi gain.

See Section 3.10 of this manual for regulatory notices and labeling requirements. Changes or modifica-

tions to a WSN802G not expressly approved by RFM may void the user’s authority to operate the

module.

Important Export Information

ECCN: 5A002.a.1 ENC

CCATS: G073573

The WSN802G products are classified under ECCN codes as 5A002.a.1 class devices and carry and

ENC encryption exception. RFM has had the WSN802G products pre-screened which allows exports to

countries listed in Supplement 3 to Part 740 of the Export Administration Requirements License Excep-

tion ENC Favorable Treatment Countries. When exporting products containing any of the WSN802G

products to this list of countries, CCATS G073573 should be referenced.

Export of the WSN802G products or products containing any of the WSN802G products to other coun-

tries will require additional review and may be prohibited.

This information is provided as a guide to exporting WSN802G-based products but it is the responsibility

of the entity exporting WSN802G products or devices to determine their actual requirements.

WSN802G Rev. 2.0 01-27-15 www.murata.com

Table of Contents

1.0 WSN802G Introduction .......................................................................................................................5

1.1 Features........................................................................................................................................... 6

1.2 Applications......................................................................................................................................6

2.0 WSN802G Operation .........................................................................................................................7

2.1 Active and Sleep Modes ..................................................................................................................7

2.2 Automatic I/O Reporting...................................................................................................................8

2.3 Data Serial Port................................................................................................................................8

2.4 Diagnostic Serial Port.......................................................................................................................8

2.5 Serial Peripheral Interface (SPI) Port...............................................................................................8

2.6 Analog I/O ........................................................................................................................................ 9

2.7 Digital I/O .......................................................................................................................................10

3.0 WSN802G Hardware.........................................................................................................................11

3.1 Absolute Maximum Ratings ...........................................................................................................11

3.2 Specifications.................................................................................................................................12

3.3 Module Interface ............................................................................................................................13

3.4 WSN802GC and WSN802GP Antenna Connector .......................................................................14

3.5 Input Voltage..................................................................................................................................15

3.6 ESD and Transient Protection .......................................................................................................15

3.7 Interfacing to 5 V Logic Systems ...................................................................................................15

3.8 Power-On Reset Requirements.....................................................................................................15

3.9 Mounting and Enclosures..................................................................................................................16

3.10 Labeling and Notices......................................................................................................................17

4.0 Application Protocol...........................................................................................................................19

4.1 I/O Read Request ..........................................................................................................................19

4.2 I/O Read - I/O Report.....................................................................................................................20

4.3 I/O Write GPIO...............................................................................................................................20

4.4 I/O Write PWM...............................................................................................................................20

4.5 I/O Write Reply...............................................................................................................................21

4.6 I/O Serial Read...............................................................................................................................21

4.7 I/O Serial Write...............................................................................................................................22

4.8 I/O SPI Read..................................................................................................................................22

4.9 I/O SPI Write..................................................................................................................................23

4.10 CFG Read......................................................................................................................................23

4.11 CFG Read Reply............................................................................................................................23

4.12 CFG Write......................................................................................................................................22

4.13 CFG Write Reply............................................................................................................................24

4.14 Configuration Parameters..............................................................................................................24

5.0 IP Address Discovery Protocol..........................................................................................................38

5.1 IP Hunt Query ................................................................................................................................39

5.2 IP Hunt Reply.................................................................................................................................39

6.0 SSID, Channel, Encryption and Authentication.................................................................................40

6.1 Connection Scanning.....................................................................................................................40

6.2 Ad Hoc Mode .................................................................................................................................40

7.0 SNMP Module Configuration.............................................................................................................41

7.1 SNMP Traps...................................................................................................................................41

7.2 SNMP Parameter OIDs.....................................................................................................................42

WSN802G Rev. 2.0 01-27-15 www.murata.com

8.0 WSN802GDK/WSN802GADK and WSN802GDK-A/WSN802GADK-A Developer’s Kits................67

8.1 Kit Contents....................................................................................................................................67

8.2 Additional Items Needed................................................................................................................67

8.3 Developer Kit Assembly and Testing.............................................................................................68

8.4 Host Configurations to Support Module Discovery .......................................................................70

8.5 Developer Board Features.............................................................................................................73

8.6 WSNConfig Program Operation.....................................................................................................75

9.0 Troubleshooting.................................................................................................................................92

10.0 Appendices........................................................................................................................................93

10.1 Ordering Information......................................................................................................................93

10.2 Technical Support..........................................................................................................................93

10.3 WSN802G Mechanical Specifications ...........................................................................................94

10.4 WSN802G Developer Board Schematic........................................................................................98

11.0 Warranty..........................................................................................................................................101

WSN802G Rev. 2.0 01-27-15 www.murata.com

1. WSN802G Introduction

The WSN802G transceiver module is a low cost, robust solution for 802.11b/g/n sensor networks. The

WSN802G is unique in that it is able to sleep while still remaining a member of an 802.11b/g/n network.

The WSN802G’s low active current and very low sleep current makes long life battery operation practical.

The WSN802G module includes analog, digital and serial I/O, providing the flexibility and versatility need-

ed to serve a wide range of sensor network applications. The WSN802G module is easy to integrate and

is compatible with standard 802.11b/g/n routers.

Figure 1.0.1

An example 802.11b/g/n network with WSN802G sensor nodes is shown in Figure 1.0.1. A sensor net-

work application running on a server or PC communicates with one or more WSN802G sensor nodes

through a commercial 802.11b/g/n router. WSN802G sensor nodes can be used with 802.11b/g/n routers

that are also serving other applications.

Figure 1.0.2

A WSN802G module is integrated with other components to create a complete sensor node. These com-

ponents include a host circuit board, a power supply (battery), sensor I/O electronics and/or a host micro-

controller, and a housing (external antenna also required on some WSN802G models). Two common

configurations are show in Figure 1.0.2. Serial sensor data communication between a WSN802G module

and its host microcontroller requires no protocol formatting. The WSN802G formats data received from its

host into UDP packets for RF transmission, and delivers the payload data from received UDP packets to

HN-210D/X, HN-214 D/X Rev. 2.0 01-16-15 Page 5 of 101 www.murata.com

its host. The sensor network application on the server or PC uses a simple protocol to send and receive

data from WSN802G sensor nodes, as detailed in Section 4. WSN802G modules can receive configura-

tion commands through either their serial port or over-the-air in UDP packets carrying SNMP commands.

1.1. Features

WSN802G modules provide a unique set of features for wireless sensor network applications:

•Compatibility with commercial and industrial 802.11b/g/n routers

•Low power consumption for long life battery operation including sleep mode

•Full -40 to +85 ºC industrial temperature range operation

•Analog and digital I/O, plus two serial and one SPI port

•Separate data and diagnostic ports

•System/application set up using just two Management Information Blocks (MIBs)

•Full 14 channel 802.11b/g coverage for world wide operation

•FCC, Canadian IC and European ETSI certifications

•Four module configurations:

WSN802GC - solder reflow mounting with RF connector for external antenna connection

WSN802GCA - solder reflow mounting with integral chip antenna

WSN802GP - plug in connector mounting with RF connector for external antenna connection

WSN802GPA - plug in connector mounting with integral chip antenna

•Automatic or manual I/O data reporting

1.2 Applications

WSN802G sensor networks are well suited to applications where IEEE 802.11b/g/n router compatibility,

industrial temperature range operation and long battery life are important. Many applications match these

criteria, including:

•Energy Monitoring and Management

•Physical Asset Management

•Cold Chain Data Logging and Food Safety

•Security and Access Control Systems

•Environmental Monitoring

•Many More

HN-210D/X, HN-214 D/X Rev. 2.0 01-16-15 Page 6 of 101 www.murata.com

2.0 WSN802G Operation

WSN802G operation is designed to support long battery life by allowing the module to stay in sleep mode

to the maximum extent possible. Compared to 802.11b/g cards used in notebook and handheld comput-

ers, the WSN802G’s active current is also very low.

2.1 Active and Sleep Modes

Once the SNMP Server IP address has been set, the default state of the WSN802G is sleep mode. The

WSN802G has a dedicated input to switch it from sleep to active mode, WAKE_IN (Pin 26). There are five

events that will wake the WSN802G from sleep mode:

•Applying a logic high signal on the WAKE_IN pin

•Expiration of the AutoReport timer

•Expiration of Linkup trap timer

•Expiration of the Config trap timer

•Module’s Primary SNMP Server IP address has not been set (this will not wake it, it prevents it

from sleeping)

The WAKE_IN pin and AutoReport can be enabled/disabled. The Linkup timer sends a keep alive packet

to the router every 60 seconds by default. The Config timer cannot be disabled and will generate a Config

trap every 10 seconds by default. Once a module has been initially configured, the Config timer is typical-

ly set to a longer interval.

When the module wakes to an active state due to either the WAKE_IN pin or the AutoReport timer, it re-

mains awake for a time period controlled by the WakeTimeout timer. The module returns to sleep mode

when the WakeTimeout timer expires, subject to the conditions listed below. The WakeTimeout timer is

held in reset and the module remains in active mode when any of the following events occur:

•A logic high signal is held on the WAKE_IN pin

•A serial byte is received

•An RF packet is sent or received

•Module’s SNMP Server IP address has not been set

The WakeTimeout feature is used to support scenarios such as a server application parsing the I/O report

and sending back a serial string or I/O output change command, or a host processor sending a serial

string and waiting for a response.

As discussed in Section 5, the SNMP Server IP address can be set in a short period of time, allowing the

module to switch to sleep mode for battery conservation. The SNMP server IP address only needs to be

set one time.

A WSN802G module that has an SNMP Server IP Address but is not linked to an 802.11b/g/n router will

cycle between sleep and active mode under the control of the scanning algorithm, even if none of the

wake events discussed above are present.

HN-210D/X, HN-214 D/X Rev. 2.0 01-16-15 Page 7 of 101 www.murata.com

Whenever the module is in active mode, a logic high is asserted on WAKE_OUT (Pin 27). WAKE_OUT

can be used to signal an external processor. When the WSN802G is in sleep mode, WAKE_OUT is set

to logic low.

2.2 Automatic I/O Reporting

The WSN802G sends an I/O report when one of the following events occur:

•A logic high signal is applied to the WAKE_IN pin

•The AutoReport timer fires (module in either active or sleep mode)

2.3 Data Serial Port

The data serial port on the WSN802G modules supports baud rates from 1.2 to 921.6 kbps. The following

serial port configurations are supported:

•5, 6, 7 and 8-bit character lengths

•1 or 2 stop bits

•Even, odd, mark, space or no parity

The default serial port configuration is 9.6 kbps, 8, N,1. See Sections 4.14 and 7.2 for serial port configu-

ration details. Serial port operation is full-duplex. Data is sent and received on the serial port transparent-

ly, with configuration information sent and received as UDP datagrams. The WSN802G includes an

acknowledgement and retry mechanism to minimize data loss on RF transmissions. However, the UDP/IP

protocol being carried by the RF transmissions does not provide guaranteed end-to-end delivery. The

user must make provisions for detecting and resending data lost on an end-to-end transmission. The

WSN802G data port is supported with optional /HOST_RTS and /HOST_CTS flow control signals.

2.4 Diagnostic Serial Port

The diagnostic serial port on the WSN802G modules supports baud rates from 1.2 to 115.2 kbps. The

default diagnostic port configuration is 9.6 kbps, 8, N,1. Diagnostic port operation is full-duplex, three-

wire, without flow control support. Diagnostic data is sent and received using a simple string protocol.

Contact RFM module technical support for diagnostic port data format information.

2.5 Serial Peripheral Interface (SPI) Port

The WSN802G SPI port provides master mode functionality at data rates configurable up to 11 Mbps. SPI

port operation is full duplex in the sense that a single clock signal simultaneously shifts data into and out

of the SPI port.

HN-210D/X, HN-214 D/X Rev. 2.0 01-16-15 Page 8 of 101 www.murata.com

Figure 2.5.1

Figure 2.5.1 shows the signals a WSN802G uses in SPI Master mode. The AutoReport function triggers

the WSN802G module to clock out a configurable command string, SPI_MasterCmdStr, to collect data

from a Slave peripheral. The collected data is then transmitted as a data message. Alternatively, a host

connected to the base can transmit an SPI command as a data message to the remote. The WSN802G

will clock the command into its Slave peripheral and transmit back the Slave’s response, as show in Fig-

ure 2.5.2. In either case, data strings are limited to 256 bytes.

Figure 2.5.2

2.6 Analog I/O

The WSN802G includes two 10-bit ADC inputs, ADC0 (Pin 18) and ADC1 (Pin 19). Pin 25 provides a full-

scale reference voltage to support ratiometric ADC measurements. ADC measurements are triggered and

added to the automatic I/O report when a logic high signal is first applied to the WAKE_ IN pin or the Au-

toReport timer fires, as discussed in Section 2.2. An ADC reading is also made on the internal buss volt-

age of the WSN802G and included in the automatic I/O report. These readings can also be retrieved any-

time the WSN802G is in active mode using the IO_REPORT application protocol command as discussed

in Section 4.1.

The WSN802G also includes a 16-bit pulse width modulated output, PWM0 (Pin 9). The PWM output is

low-pass filtered to provide an analog output voltage with ripple suppressed to 7 bits. External low-pass

filtering can be added to further suppress ripple. The full-scale PWM output is referenced to the regulated

HN-210D/X, HN-214 D/X Rev. 2.0 01-16-15 Page 9 of 101 www.murata.com

supply voltage (Pin 24). The PWM output is set using the IO_ WRITE_PWM application protocol com-

mand, as discussed in Section 4.4.

2.7 Digital I/O

The WSN802G includes four general purpose input/output (GPIO) ports, GPIO0 (Pin 4), GPIO1 (Pin 11),

GPIO2 (Pin 10) and GPIO3 (Pin 12). When programmed as inputs, GPIO pins include an internal weak

pull-up. The states of pins configured as inputs are captured as part of the automatic I/O report when a

logic high signal is applied to the WAKE_IN pin or the AutoReport timer fires, as discussed in Section 2.2.

These readings can also be retrieved anytime the WSN802G is in active mode using the

IO_READ_REQUEST application protocol command as discussed in Section 4.1. The states of GPIO

pins configured as outputs are set using the IO_WRITE_GPIO application protocol command as dis-

cussed in Section 4.3.

HN-210D/X, HN-214 D/X Rev. 2.0 01-16-15 Page 10 of 101 www.murata.com

Inhaltsverzeichnis

Andere Murata Netzwerk-Hardware Handbücher

Murata

Murata LBEE58D1VF-TEMP Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung