Murdock BF1 Series Montage- und Bedienungsanleitung

1.800.591.9360

Technical Assistance Fax: 1.626.855.4894

TECHNICAL ASSISTANCE TOLL FREE TELEPHONE NUMBER:

Date: 07/15/16

BF1 Series

Bottle Filler, Pushbutton Operated

I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S

NOTES TO INSTALLER:

1. Please leave this documentation with the owner of the fixture when finished.

2. Please read this entire booklet before beginning the installation.

3. Check your installation for compliance with plumbing, electrical and other applicable codes.

LIMITED WARRANTY - UNITED STATES & CANADA

Murdock warrants that its products are free from defects in material or workmanship under normal use and

service for a period of one year from date of original shipment or for 18 months after the date of shipment from the

factory, whichever comes first. Murdock’s liability under this warranty shall be discharged solely by replacement

or repair of defective material, provided Murdock is notified in writing within one year from date of shipment,

F.O.B. Industry, California.

This warranty does not cover installation or labor charges and does not apply to materials, which have been

damaged by other causes such as mishandling or improper care or abnormal use. The repair or replacement of the

defective materials shall constitute the sole remedy of the Buyer and the sole remedy of Murdock under this

warranty. Murdock shall not be liable under any circumstances for incidental, consequential or direct charges

caused by defects in the materials, or any delay in the repair or replacement thereof. This warranty is in lieu of all

other warranties expressed or implied. Product maintenance instructions are issued with each unit and disregard

or non-compliance with these instructions will constitute an abnormal use condition and void the warranty.

Stainless steel must be protected on job site during construction and must be properly maintained after the water

has been introduced into the water cooler or drinking fountain, or Murdock’s limited warranty is void.

LIMITED EXPORT WARRANTY - One year on parts only.

COMPLIES WITH

Member of

MURDOCK

15125 Proctor Ave.

City of Industry, CA

91746 U.S.A.

Phone 800-591-9360

626-336-4561

Fax 626-855-4894

Murdock assumes no responsibility for use of void or

suspended data. © Copyright Murdock, City of

Industry, CA Member of Morris Group International.

Please visit www.murdockmfg.com for most

current specifications.

7109-708-001

www.murdockmfg.com

WATER COOLERS

MCBF1 (Install/Maintenance Instructions)

I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S

Page 2 of 10

CONTEMPORARY WATER COOLERS

Date: 04/03/18

I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S

7109-708-001

WATER COOLERS

MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA

Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com Member of

Please visit www.murdockmfg.com

for most current specifications.

PRIOR TO INSTALLATION

Important: Some options may slightly alter installation. To ensure proper installation review the manual thoroughly and verify

rough-ins before beginning any work. File this manual with the owner or maintenance personnel upon completion of installation

— Fixture mounting requirements: Industry standard wall construction, adequate to support the fixture and (installer provided) wall

anchors sufficient to secure the fixture.

— Fixture operates within water pressure range of 20 to 105 psig. Murdock will not warranty fixtures damaged when connected to

supply lines with flow pressure lower than 20 psig or higher than 105 psig.

— Per UPC 609.10- All building water supply systems in which quick acting valves are installed shall be provided with devices to

absorb the hammer caused by high pressure resulting from the quick closing of the valve. These pressure-absorbing devices

shall be approved mechanical devices. Water pressure-absorbing devices will be installed as close as possible to the quick

closing valve.

— Water supply inlet is 1/4” OD polyethylene tube.

— Completely flush supply of all foreign debris before connecting to fixture. Bottle filler is designed to provide trouble free drinking

water unaffected by fixture connection tubing and fittings and not cause problems with taste, odor, color or sediment.

INSTALLATION INSTRUCTIONS:

1. Remove drinking cooler access panel and shut off water supply, then actuate valve to relieve pressure.

2. Drill 1/2” dia. hole thru drinking cooler deck (where shown above). Deburr hole and install grommet provided.

Drilling Notes:

— Wear approved safety glasses when drilling.

— Prior to drilling stainless steel, adhere masking tape over drilling area to protect finish and provide

marking surface.

— Use a short, sharp high-speed drill bit and drill speed of 400-600 RPM; applying heavy pressure. Drill

must cut at all times. DO NOT allow drill bit to ride, this will cause work hardening and will make it

very difficult to drill or tap. Bibb washers, placed on drill shank will help to prevent marring the surface

after the drill has broke through.

3. Mark vertical (plumb) center line on the wall, at the center of the drinking cooler deck.

(127)

(51)

Ø1

MCBF1 (Install/Maintenance Instructions)

I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S

Page 3 of 10

CONTEMPORARY WATER COOLERS

Date: 04/03/18

I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S

7109-708-001

WATER COOLERS

MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA

Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com Member of

Please visit www.murdockmfg.com

for most current specifications.

INSTALLATION INSTRUCTIONS CONTINUED:

(76)

(76) 3

8" (9.5) x 4 Mounting Anchors

(By Others)

103

(262)

(73)

Alignment

Notch

Horizontal Mounting

Channel

To Filler Tube

Valve Inlet

From Evaporator

Out Tee Fitting

Bottle Filler Mounting

Frame

Horizontal Mounting

Channel

Water Cooler

(Shown For Reference)

Air Line Inlet

Note: Housing not shown

for clarity

4. Carefully disassemble bottle filler. Remove the top, frame, horizontal mounting channels, and disconnect the PE tubing from

the fill tube. (see page 5)

5. Use the frame as template, align notches in the frame with the vertical center line, and with the frame sitting on the deck

NOTE: COOLER SHOULD BE LEVEL.

6. Mark four mounting holes.

7. Install the four wall anchors (by others).

8. Align mounting frame and horizontal mounting channels to the anchors (as shown) and attach to wall with mounting fasteners

(by others).

9. In drinking cooler access compartment, attach the “Y” strainer (provided) to existing 3/8” OD copper inlet tube and connect

outlet of “Y” strainer to existing 1/4” OD evaporator inlet tube. (see page 4).

10. *In drinking cooler access compartment, remove the 1/4” push-in fitting from evaporator outlet and replace it with 1/4” push-in

tee fitting. Reconnect the PE tube from the cartridge valve assembly to top of tee. (See page 4)

*See insert detail on page 4, for special installation instructions when installing on bi-level drinking fountains.

11. Remove the 18” piece of insulation from the 1/4” OD 30” PE tube. Pass the end of the 30” PE tube through the hole in the

deck of the drinking cooler. Reinstall 18” piece of insulation on to the 30” PE tube, under deck. Connect the 30” PE tube to

the side of the previously installed tee fitting, from step 10. (see page 4).

12. Reconnect 24” PE to fill tube.

13. To reassemble housing to mounting frame assembly, engage the left side of the housing behind the horizontal mounting

channels, then stretch the housing over the right end of the horizontal mounting channels, make sure that the rubber trim on

the housing is touching the water cooler deck. Secure the housing to the top channel, with #10-32 truss head screws

provided.

14. reassemble and install top with #8-32 truss head screws provided.

15. Turn on the water supply stop, test unit and check for leaks, then reinstall access panel.

I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S

Page 4 of 10

CONTEMPORARY WATER COOLERS

Date: 04/03/18

I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S

7109-708-001

WATER COOLERS

MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA

Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com Member of

Please visit www.murdockmfg.com

for most current specifications.

MCBF1 (Install/Maintenance Instructions)

INSTALLATION INSTRUCTIONS CONTINUED:

WATER TUBING CONNECTIONS

cartridge

30" PE Tube to

valve inlet

From cold water tube

from evaporator

Cut tube

and

Install tee

Special Instructions

Bi-Level Drinking Fountains

ONLY INSERT DETAIL

When mounting bottle filler on unit with no

compressor, only.

NOTE: Insulation on all water tubes not shown (all PE

water tubes are insulated).

Fill Tube

Pushbutton Assembly

Valve Outlet Elblow

w/ Flow Control

Valve Inlet Fitting

Hole in Deck

Drinking Foutain

(Shown for Reference)

"Y" Strainer

Evaporator

30" Ø 1

4" PE Tubing

Evaporator Inlet

To Cartridge

Push-In Tee

Evaporator Outlet

3/8" OD Copper

inlet (by others)

1/4 x 3/8 Adapter

Pushbutton Air Line

1/4 Turn Shut-Off Valve

I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S

Page 5 of 10

CONTEMPORARY WATER COOLERS

Date: 04/03/18

I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S

7109-708-001

WATER COOLERS

MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA

Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com Member of

Please visit www.murdockmfg.com

for most current specifications.

MCBF1 (Install/Maintenance Instructions)

RETRO-FIT INSTALL FOR EXISTING WATER COOLER FIXTURE:

PRESSURIZED SINGLE UNIT PIPE INSTALLATION (WITH -GF & -BF OPTIONS)

ITEM PART NUMBER DESCRIPTION QTY.

1 7012-055-000 FOAM INSULATION, PIPE, 3/8" ID x 1/4" THICK 5.5'

2 2169-000-000 TUBING, LLDPE, BLUE 1/4" OD 5'

17" Water Supply Tubing

13" Water Supply Tubing

1 2

To Bottle Filler or Glass Filler

I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S

Page 6 of 10

CONTEMPORARY WATER COOLERS

Date: 04/03/18

I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S

7109-708-001

WATER COOLERS

MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA

Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com Member of

Please visit www.murdockmfg.com

for most current specifications.

MCBF1 (Install/Maintenance Instructions)

RETRO-FIT INSTALL FOR EXISTING WATER COOLER FIXTURE (NON-PRESSURIZED UNIT):

RE-PIPING FROM NON-PRESSURIZED TO PRESSURIZED (FOR -GF & -BF ONLY)

To re-pipe a single non-pressurized unit to pressurized, you will have to move the water supply tubing around, with “NO”

additional tubing needed. Before performing this task you MUST SHUT OFF THE WATER SUPPLY, and disconnect all supply

connections.

STEP 3:

From the outlet of the cartridge assembly, connect to

the bubbler.

STEP 1:

Starting with the supply line coming from the wall,

connect to the inlet of the evaporator assembly.

STEP 2:

From the outlet of the evaporator assembly, connect to

the inlet of the cartridge assembly.

Wall Supply Connection

17" Water Supply Tubing

Evaporator Inlet Connection

13" Water Supply Tubing

Bubbler Connection

Cartridge Assembly

Outlet Connection

Cartridge Assembly

Inlet Connection

Evaporator Outlet Connection

To Bottle Filler or Glass Filler

Add 1

4" Tee for Both BF or GF

I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S

Page 7 of 10

CONTEMPORARY WATER COOLERS

Date: 04/03/18

I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S

7109-708-001

WATER COOLERS

MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA

Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com Member of

Please visit www.murdockmfg.com

for most current specifications.

MCBF1 (Install/Maintenance Instructions)

PUSH-IN FITTING INSTALLATION

NOTE: FITTINGS AND TUBE SHOULD BE KEPT

CLEAN, BAGGED AND UNDAMAGED PRIOR TO

INSTALLATION.

2. Pull on the fitted tubing to ensure it is secure. Tube

should not come free from the fitting. Water test the

connection assembly prior to leaving the site to ensure

there are no leaks.

DISCONNECTING THE TUBE:

To disconnect the tube from the fitting ensure that the

water line is depressurized. Push collet square towards

the push-in fitting body and hold. While holding the collet

in, pull on the PE tubing to remove from the push-in fitting.

TO CUT TUBE:

Cut to fit length of 1/4” PE tubing and remove any burrs

or sharp edges. Ensure that the outside diameter is free

from score marks. Tube ends should be square.

INSERTING THE TUBE:

1. Firmly and fully insert the tubing end into the push-in

fitting up to the tube stop located approximately ½”

deep.

COLLET

O-RING

TUBE STOP

COLLET

I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S

Page 8 of 10

CONTEMPORARY WATER COOLERS

Date: 04/03/18

I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S

7109-708-001

WATER COOLERS

MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA

Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com Member of

Please visit www.murdockmfg.com

for most current specifications.

MCBF1 (Install/Maintenance Instructions)

START UP:

1. Air within the bottle filler system or the structure supply pipping will cause an irregular spout outlet stream until

purged out by incoming water. Hold cup (or similar object) directly below filler spout is recommended when first

activating bottle filler to prevent excessive splashing. Press and hold pushbutton until steady water stream is

achieved.

2. Using the same method, hold cup (or similar object) directly over bubbler(s) and active bubblers until air is purged

out and a steady stream is achieved.

OPERATING INSTRUCTIONS:

Hold container to be filled just below the filler tube in the center of the unit, then push pushbutton. When the container

is almost filled, release the pushbutton.

Push Button

Bottle Filler Label

Fill Spout

I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S

Page 9 of 10

CONTEMPORARY WATER COOLERS

Date: 04/03/18

I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S

7109-708-001

WATER COOLERS

MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA

Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com Member of

Please visit www.murdockmfg.com

for most current specifications.

MCBF1 (Install/Maintenance Instructions)

TROUBLE SHOOTING:.

1. RESTRICTED OR NO WATER FLOW

a. Ensure Water Supply service stop valve is fully open.

b. Verify minimum 20 psig supply line flow pressure.

c. Check for twist or kinks in spout tubing.

d. Check the water inlet “Y’’ strainer. Sediment from the main supply can get trapped in the screen along with

installation materials such as pipe dope and flux. The screen should be cleaned and checked on a regular

basis and replace if needed.

e. Flow control in solenoid valve outlet elbow clogged remove & clean.

f. The water cooler may also develop a freezing condition in which the water will become frozen inside the

evaporator coil. This indicates a refrigeration problem or thermostat failure in which case the water cooler

needs to be checked by a qualified technician.

CLEANING & MAINTENANCE GUIDE:

1. To remove water spots or rust spots, stainless steel cleaner/polish on a cloth is recommended.

2. If there are stubborn spots or if you wish to treat a scratch, synthetic abrasive general purpose pads such as

scotch brite are recommended.

3. Apply stainless steel cleaner/polish to the synthetic abrasive pads and carefully rub the panel with the grain.

4. DO NOT use harsh chemicals, abrasive or petroleum based cleaners. Use of these will void the Murdock

warranty. DO NOT use abrasives on powder coated units.

5. Stainless steel should be kept clean at all times. If a coating of stainless steel cleaner/ polish is maintained,

stainless steel surfaces will retain their new, clean, polished appearance indefinitely. Use clean mild soapy

water for powder coated units.

6. Periodically remove access panel of cooler and clean out inline “Y’’ strainer.

I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S

Page 10 of 10

CONTEMPORARY WATER COOLERS

Date: 04/03/18

I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S

7109-708-001

WATER COOLERS

MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA

Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com Member of

Please visit www.murdockmfg.com

for most current specifications.

MCBF1 (Install/Maintenance Instructions)

BOTTLE FILLER PARTS

BREAKDOWN

ITEM #

PART NUMBER DESCRIPTION ITEM # PART NUMBER DESCRIPTION

1 7014-004-199 Bottle Filler Top 12 7014-010-199 Bottle Filler Trim (Right)

2 7000-415-000 Self-Retaining J-Nut, SS 13 7013-210-001 1/4" "Y" Strainer, Bottle Filler

3 7014-007-001 Channel and Valve Assembly 14 7013-020-000 5/8" OD Grom m et

4 0316-018-00 10-32 Stn Stl Nut Retainer 15 1895-710-000 1/4" Push-in Union Tee

5 7013-027-002 Air-Control Valve As sem bly 16 7014-006-199 Bottle Filler Frame

6 2150-002-199 1/8" x 10" O.D. Clear PE Tubing 17 0112-021-000 #10-32 x 1/2" S/S Hex Btn Hd Screw

7 2169-000-000 1/4" OD LLDPE Tubing, Blue 18 7013-008-199 Bottle Filler Channel

8 2566-160-001 Pushbutton Assem bly 19 1895-123-000 1/4" x 3/8" OD Push-In Tube Union

9 0279-002-000 #8-32 Socket Cap Btn Hd Screw 20 7012-055-000 Foam Insulation

10 7014-000-003 Bottle Filler Sub Assembly 21 7000-420-000 1/4 Turn Shut-Off Valve

11 7014-009-199 Bottle Filler Trim (Left) 22 7014-005-199 Bottle Filler Top Bracket

15 19

30"

12"

18"

24"

Inhaltsverzeichnis

Andere Murdock Wasserspender Handbücher

Murdock

Murdock H2O To Go BF15 Series Montage- und Bedienungsanleitung

Murdock

Murdock A171.8-UG-SO Series Montage- und Bedienungsanleitung

Murdock

Murdock AI81.8 Series Bedienungsanleitung

Murdock

Murdock BF158 Series Bedienungsanleitung

Murdock

Murdock A172.8-UG Series Montage- und Bedienungsanleitung

Murdock

Murdock BF3 series Bedienungsanleitung

Murdock

Murdock BF2 Series Montage- und Bedienungsanleitung

Murdock

Murdock A611.8 Series Montage- und Bedienungsanleitung

Murdock

Murdock A171.8-SOC Series Bedienungsanleitung

Murdock

Murdock H2O To Go BF12 Series Montage- und Bedienungsanleitung

Murdock

Murdock A172.8FGVR Series Montage- und Bedienungsanleitung

Murdock

Murdock A171.8 Series Bedienungsanleitung

Murdock

Murdock A611108F-G Montage- und Bedienungsanleitung

Murdock

Murdock A171-UG-SO Series Montage- und Bedienungsanleitung

Murdock

Murdock A511.5 Series Montage- und Bedienungsanleitung

Murdock

Murdock A172108F-UBL Montage- und Bedienungsanleitung

Murdock

Murdock A171.8-UG-D1-BFS Series Montage- und Bedienungsanleitung

Murdock

Murdock BF11 Series Montage- und Bedienungsanleitung

Murdock

Murdock A172.8-UG-D1-BFS Series Montage- und Bedienungsanleitung

Murdock

Murdock A171 Series Bedienungsanleitung

Murdock

Murdock A171.8FGVR Series Montage- und Bedienungsanleitung

Beliebte Wasserspender Handbücher anderer Marken

Monarch Water

Monarch Water ULTIMATE MINI AQUA HE Bedienungsanleitung

Haier

Haier HLM-109B Bedienungsanleitung

abc

abc Fleck 5600SXT Bedienungsanleitung

GE GXOF18G Betriebsanleitung

Kenmore

Kenmore 625.385560 UltraFilter 650 Bedienungsanleitung

Innova

Innova CEV+ Kurzanleitung

Aries

Aries Hydra DI Handbuch

GE GNCF02H Bedienungsanleitung

ProFlo

ProFlo PFB Series Bedienungsanleitung

Hydrotech

Hydrotech 89DF HIM Bedienungsanleitung

A.O. Smith

A.O. Smith FREZYA 300S Bedienungsanleitung

Frakco

Frakco Travelsoft RV 2400HD Bedienungsanleitung

GE GXSF30V Betriebsanleitung

Avanti

Avanti WD31EC Bedienungsanleitung

Avanti

Avanti WD360 Bedienungsanleitung

BRIO

BRIO CLCTTL520 Benutzerhandbuch

3M HCD-1 Bedienungsanleitung

Elkay

Elkay EFHFA8_2CJO Installationshandbuch