Murphy PowerCore TEC-10 Bedienungsanleitung

00-02-0977

2018-02-23

Section 30

PowerCore®

Model TEC-10

Installation Manual

Products covered in this document comply with European Council electromagnetic

compatibility directive 2014/30/EU and electrical safety directive 2014/35/EU.

In order to consistently bring you the highest quality, full-featured products, we reserve the

right to change our specifications and designs at any time. The latest version of this

manual can be found at enovationcontrols.com.

BEFORE BEGINNING INSTALLATION OF THIS MURPHY

PRODUCT:

•Read and follow all installation instructions.

•Visually inspect this product before installation for

any damage during shipping.

•Disconnect all electrical power to the machine.

Failure to do this before welding can result in

damage to the panel and/or its components.

•It is your responsibility to have a qualified

technician install the unit and make sure the

installation conforms to local codes including, but

not limited to, double insulation and fire

containment.

•Observe all Warnings and Cautions in each

section of these instructions.

•The TEC-10 is designed for use in industrial

environments for monitoring and control which

include engine driven pumps, compressors,

grinders, chippers and rock crushers. Potential

difficulties may exist when ensuring

electromagnetic compatibility in other

environments due to conducted as well as

radiated disturbances.

Contact Enovation Controls Technical Service if you

have any questions or concerns at: +1 918-317-4100.

IMPORTANT! Improper use and operation of electronic

products can be dangerous. It is required that point-of-

operation guarding devices be installed and maintained.

All such devices must meet OSHA and ANSI Machine

safety standards. The manufacturer shall not accept

any responsibility for installation, application or safety of

systems.

Table of Contents

Operations Manual Location................................................. 2

Hardware Installation ............................................................. 2

Inspecting Package Contents....................................... 2

Tools Needed ............................................................... 2

Installation .................................................................... 3

Dimensions for Installation ................................................... 4

PIN Specifications................................................................... 6

Accessories ............................................................................. 7

Specifications.......................................................................... 8

Interface ....................................................................... 8

Power Supply ............................................................... 8

Inputs (9) ...................................................................... 8

Outputs (8).................................................................... 8

Communications........................................................... 8

Mating Connectors ....................................................... 8

Physical / Environmental .............................................. 8

Section 30 00-02-0977

2018-02-23 - 1-

The TEC-10 can be set as an AutoStart Controller.

Please be cognizant at all times of hands and other

objects that are in close proximity to the machine(s)

being controlled as they may commence operation

suddenly and without warning.

LENS CLEANING PROCEDURES

The lens on the TEC-10 is composed of Polycarbonate

materials. Use only mild soap and water to clean the

lens/display window. Evidence of improper cleaning

techniques or chemicals includes cracks, smear marks,

scratches, or fogged/hazy lenses.

Section 30 00-02-0977

2018-02-23 - 2-

Operations Manual Location

After installation, please review the TEC-10 Operations Manual

prior to placing the controller into service. In order to access the

TEC-10 Operation Manual, please visit:

support.enovationcontrols.com

Then search for TEC-10. Download the latest manual by clicking

the link under the Manuals section of the page.

Hardware Installation

Inspecting Package Contents

Before attempting to install the product, it is recommended that

you ensure all parts are accounted for and inspect each item for

damage (which sometimes occurs during shipping). The items

included in the box are:

TEC-10 Controller kit – P/N 40-70-0495 includes:

•TEC-10 Control Panel

•Mounting Kit:

o4 Shockmount Isolators

o4 ¼ x 20 Hex Keps Nuts

•TEC-10 Installation Manual – P/N 00-02-0977

Tools Needed

Use a 9/32 or 7.5mm drill bit to make the approximately sized

0.28125” or 7.5mm mounting holes.

Use a 7/16” or 11mm torque wrench for shockmount nut

installation.

Section 30 00-02-0977

2018-02-23 - 3-

Installation

Preparing the Enclosed Panel

Determine the location of the TEC-10 Panel on the customer-

supplied mounting bracket or plate. The suitability of the location

is subject to investigation by the local authority having jurisdiction

at the time of the installation.

Recommended torque for tightening both the shockmounts into

the panel and the nuts on the shockmounts is 78 inch-pounds or

8.8 Nm (Newton Meters). Although thread lock is not required,

only blue polycarbonate compatible thread lock should be used

for the TEC-10 mounting screws.

Section 30 00-02-0977

2018-02-23 - 4-

Dimensions for Installation

Front Inches

[mm]

Side View

Section 30 00-02-0977

2018-02-23 - 5-

Back View

Section 30 00-02-0977

2018-02-23 - 6-

PIN Specifications

21 Pin Connector (A)

31 Pin Connector (B)

Unavailable

Battery (positive)

Unavailable

Relay 1, +DC (10A), Default Setting: Crank

Unavailable

Battery (negative)

Unavailable

J1939 CAN Shield

Unavailable

Relay 2, +DC (10A), Default Setting: ECU

Enable

Unavailable

Alternator Excite Output, +DC (1A)

Analog Input 3, Default Setting: Not Used

Unavailable

Digital Output 1, +DC, (1A), Default Setting: Not in

Auto)

Unavailable

Digital Input 3, Default Setting: Dual Contact Stop,

B-

Digital Output 3, -DC, (1A), Default Setting:

Throttle Decrease)

Unavailable

Digital Output 4, -DC, (1A), Default Setting:

Throttle Increase

Unavailable

Frequency Input

Relay 3 Common (RLY 3 Defaulted to Not Used)

10A Max

J1939 CAN Low (includes terminating resistor,

Default to ON)

Relay 3 NC (RLY 3 Defaulted to Not Used) 10A

Max

J1939 CAN High, (includes terminating

resistor, Default to ON)

Relay 3 NO (RLY 3 Defaulted to Not Used) 10A

Max

Analog Input 2, Default Setting: Not Used

Digital Input 5, Default Setting: Low Lube Oil Level

B-

Analog Input 1, Default Setting: Not Used

Digital Input 1, Default Setting: Not Used

NOTE: Wiring of this device must

meet all applicable electrical codes.

Unavailable

Digital Input 2, Default Setting: Dual Contact Start,

B-

Digital Output 2, +DC, (1A), Default Setting: Engine

Running)

Unavailable

Battery (negative)

Unavailable

Digital Input 4, Default Setting: Low Coolant Level,

B-

RS485 (positive)

RS485 (negative)

Section 30 00-02-0977

2018-02-23 - 7-

Accessories

Part

Number

Description

40000602

Engine Harness, 21 Position Connector 10’ Whip

Harness (3m approx.)

40000603

I/O Harness, 31 Position Connector 10’ Whip

Harness (3m approx.)

40000479

Deutsch Connector Kit, 21-pin and 31-pin, Panel

Connector Kit

40000531

Deutsch Connector Kit, 21-pin, Panel Connector

Kit, Engine Only

78700046

Deutsch Connector Kit, 31-pin, Panel Connector

Kit, I/O Only

40051073

Replacement Fuse Door

40051143

Replacement Fuse Door Pad

40000601

Replacement Shock Mount Kit

40000636

Replacement Key Set

40000625

TEC-10 Programming Kit

Inhaltsverzeichnis

Andere Murphy Controller Handbücher

Murphy

Murphy Cascade CD101 Bedienungsanleitung

Murphy

Murphy Automatic Engine Controller A88 Bedienungsanleitung

Murphy

Murphy Glow Plug Control Module GPM92 Bedienungsanleitung

Murphy

Murphy Autostart AS731 Bedienungsanleitung

Murphy

Murphy Engine Throttle Controller AT-04060N Bedienungsanleitung

Murphy

Murphy EMS447 Bedienungsanleitung

Murphy

Murphy LR857 Bedienungsanleitung

Murphy

Murphy EMS PRO Bedienungsanleitung

Murphy

Murphy Engine Throttle Controller AT-67207 Bedienungsanleitung

Murphy

Murphy iGUARD AL-02058B Bedienungsanleitung

Murphy

Murphy PowerCore MPC-20 Bedienungsanleitung

Murphy

Murphy Autostart 705 AS705S Bedienungsanleitung

Murphy

Murphy Auto-Start/Stop Controller Cascade Bedienungsanleitung

Murphy

Murphy Centurion Configurable Controller CE-05171N Bedienungsanleitung

Murphy

Murphy Selectronic Micro-Controller Series 1500 Bedienungsanleitung

Murphy

Murphy CONNECT Bedienungsanleitung

Murphy

Murphy iGUARD Bedienungsanleitung

Murphy

Murphy LR579 Bedienungsanleitung

Murphy

Murphy Autostart 710 AS710S Bedienungsanleitung

Murphy

Murphy Cascade CD101 Bedienungsanleitung

Murphy

Murphy Engine and Generator Controls Keystart 9620 Bedienungsanleitung

Murphy

Murphy Automatic Engine Controller EA150 Bedienungsanleitung

Murphy

Murphy MX4 Series Bedienungsanleitung

Murphy

Murphy Keystart 9700 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung