Musical Fidelity MM/MC PHONO STAGE M1 VINL Bedienungsanleitung

Instructions for use

Thank you for purchasing the Musical Fidelity M1 ViNL

The M1 ViNL consists of a top quality phono stage with precise RIAA or RIAA/IEC frequency response. It

features switchable loading options for all cartridge types and high quality buffered single ended and balanced

outputs.

This combination yields one of the best high-fidelity systems available at any price.

It is designed particularly to be partnered with Musical Fidelity M1/M3/M6 series products or to add top quality

phono playback to any system

The M1 ViNL should give many years of outstanding musical reproduction. Dust regularly with a soft duster or

soft brush, but be careful when using cleaning or polishing agents - they may harm the surface finish.

If there are any questions about the audio system, please consult the dealer who is there to help and advise.

M1 ViNL manual issue 2.doc2 Page 2 of 12

Section Page

Safety Information – Mains plug (UK only), modification warning 3

General advice – Installation precautions 4

Disposal information – EU disposal information 5

Installation – Introduction, cleaning, installation, power connections, audio

connections

Facilities and connections – Illustrations - main unit front & rear panels 7

– Switch on and introduction 8

– Cartridge characteristics

Operation

– Choosing cartridge type, RIAA and RIAA/IEC, MM Loading

resistor selection, MM loading capacitor selection, MC loading

resistor selection, trigger input and output.

Problems? – Basic fault finding 10

Specifications 11

Manual history 12

CONTENTS

M1 ViNL manual issue 2.doc2 Page 3 of 12

IMPORTANT! (U.K. only)

This unit is supplied in the U.K. with mains lead fitted with a moulded 13 amp plug. If, for any reason, it is

necessary to remove the plug, please remove the fuse holder and dispose of the plug safely, out of reach of

children.

It must not be plugged into a mains outlet.

The wires in the mains lead supplied with this appliance are coloured in accordance with the following code:

Green and yellow .............................Earth

Blue................................................ Neutral

Brown ..................................................Live

WARNING – This appliance MUST be earthed

As the colours of the wires of the mains lead of this appliance may not correspond with the coloured markings

identifying the terminals in the plug, proceed as follows:

• The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked

with the letter E or coloured green or green-and-yellow, or by the earth symbol:

• The wire which is coloured brown must be connected to the terminal which is marked with the letter L or

coloured red.

• The wire which is coloured blue must be connected to the terminal which is marked with the letter N or

coloured black.

• If connecting to a BS1363 plug, a 13 amp fuse must be used.

WARNING:

ANY MODIFICATIONS TO THIS PRODUCT NOT EXPRESSLY

APPROVED BY MUSICAL FIDELITY WHO IS THE PARTY RESPONSIBLE

FOR STANDARDS COMPLIANCE COULD VOID THE USER'S

AUTHORITY TO OPERATE THIS EQUIPMENT.

SAFETY INFORMATIONSAFETY INFORMATION

M1 ViNL manual issue 2.doc2 Page 4 of 12

Installation, Precautions & User Information

This new M1 VINL is designed and built to provide trouble-free performance, but as with all electronic devices it

is necessary to observe a few precautions:

• Heed all warnings shown on the back of the product.

• The M1 ViNL has a built-in universal power supply that can be connected to mains of between 80 to 253V

AC r.m.s. 50-60Hz without modification.

• Always ensure that when disconnecting and reconnecting your audio equipment the mains supply is

switched off.

• Position the mains lead and signal interconnects where they are not likely to be walked on or trapped by

items placed on them.

• Do not use near water, or place water-filled containers on the M1 VINL, for example, a flower vase or potted

plants. If water does spill inside, immediately pull out the mains plug from the wall socket and inform

the dealer, who should then check the unit before further use. Entry of liquid into the M1VINL is

dangerous, and may cause electric shock or fire hazard.

• Do not place the unit near direct heat sources such as radiators, direct sunlight or other equipment.

• Do not remove any covers or try to gain access to the inside. There are no user adjustments or fuses to

change without qualification. Refer all service work to an authorised Musical Fidelity agent.

* Note: Unauthorised opening of the equipment will invalidate any warranty claim.

• Dust regularly with a soft cloth or soft brush but be careful when using cleaning or polishing agents - they

may harm the surface finish.

The electronics in modern hi-fi equipment is complex and may, therefore, be adversely affected or damaged by

lightning. For protection of the audio system during electrical storms, remove the mains plugs.

If after-sales service is required, to help the dealer identify the M1 VINL please quote the serial number located

on the rear panel of the unit.

GENERAL ADVICE

M1 ViNL manual issue 2.doc2 Page 5 of 12

DISPOSAL

The crossed out wheeled bin label that appears on the back panel of the product indicates that the product must

not be disposed of as normal household waste. To prevent possible harm to the environment please separate the product

from other waste to ensure that it can be recycled in an environmentally safe manner. Please contact local government

office or retailer for available collection facilities.

DISPOSITION

La poubelle sur roulettes barrées X, qui apparaît en logo sur le panneau arrière du produit, indique que celui-ci ne

doit pas être traité comme un déchet domestique commun. Afin de protéger l'environnement, ce produit électronique devra

être géré séparément et donc recyclé selon les nouvelles normes Européennes Rohs concernant les déchets d'appareils

électroniques. Prière de contacter les services concernés gouvernementaux ou votre point de vente pour l'élimination et

l'enlèvement de déchets électroniques équipés de composants électroniques.

DISPOSAL

La etiqueta cruzada hacia fuera del compartimiento que aparece en el panel trasero del producto indica que el

producto no se debe reciclarse como basura normal de la casa. Para prevenir daños posible al ambiente separe por favor el

producto de otras basura para asegurarse de que puede ser reciclada de una manera ambientalmente segura. Entre en

contacto por favor a su oficina gubernamental local o a su minorista para las instalaciones disponibles de la colección.

RIFIUTI

L'etichetta del cassonetto barrato riportato sul retro dell'apparecchio indica che il prodotto non deve essere

smaltito tramite la procedura normale di smaltimento dei rifiuti domestici. Per evitare eventuali danni all'ambiente, separare

questo prodotto da altri rifiuti domestici in modo che possa venire riciclato in base alle procedure di rispetto ambientale. Per

maggiori dettagli sulle aree di raccolta disponibili, contattate l'ufficio govenativo locale od il rivenditore del prodotto.

FACHGERECHTE ENTSORGUNG:

Das auf der Geräterückseite angebrachte Label deutet darauf hin, dass das Produkt nicht mit konventionellem

Hauskehricht entsorgt werden darf. Um Schäden und Verschmutzungen an Umwelt und Mensch zu vermeiden, muss das

Produkt fachgerecht entsorgt und von anderem Abfall getrennt werden. Wenden Sie sich bei Fragen hierzu an Ihren

Fachhändler oder an eine öffentliche Informationsstelle.

AFVAL

Het label op de achterzijde van dit apparaat, een afvalbak op wielen met een kruis doorgehaald, geeft aan dat dit

apparaat niet samen met gewoon huishoudafval mag worden weggegooid. Om mogelijke schade aan onze leefomgeving te

voorkomen dient dit apparaat, gescheiden van gewoon huishoudelijk afval, te worden afgevoerd zodat het op een

milieuvriendelijke manier kan worden gerecycled. Neem voor beschikbare inzamelplaatsen contact op met uw gemeentelijke

reinigingsdienst of met uw elektronica leverancier.

HÄVITTÄMINEN

Yliruksattua jäteastiaa kuvaava tarra tuotteen takalevyssä kertoo, että tuotetta ei saa käsitellä normaalina

talousjätteenä. Ympäristön suojelemiseksi on tuote pidettävä erillään muusta jätteestä ja se on kierrätettävä ekologisesti

kestävällä tavalla. Ota yhteyttä laitteen myyjään tai Pirkanmaan Ympäristökeskukseen lähimmän kierrätyskeskuksen

löytämiseksi.

AFSKAFNING

Logoet med en skraldespand med kryds over på bagsiden af apparatet indikerer at dette produkt ikke må kasseres

som normal husholdningsaffald. For at forebygge mulig skade på miljøet, bedes De separere dette produkt fra andet affald,

og sikre at det bliver genbrugt på en miljørigtig måde. Kontakt venligst de lokale myndigheder eller din forhandler for

oplysning om nærmeste tilgængelige opsamlingssted for elektronikaffald.

 

           



            .

     ,      

         .

           

  .

ITEM DISPOSAL INFORMATION

M1 ViNL manual issue 2.doc2 Page 6 of 12

Introduction

Congratulations on the purchase of the new M1 ViNL player. This unit will give top quality performance when

used as a top quality record player delivering the best performance possible from vinyl recordings.

Cleaning

Before cleaning the unit, switch off power at the mains switch and remove the mains plug from the wall socket.

Clean the cabinet and remote control unit using a moist cloth. Using solvents, white spirit or thinners is not

advised, as they could damage the surface finish.

Installation

Position the M1 ViNL on a stable, horizontal surface where there is no risk of it being knocked, or subjected to

vibration such as from loudspeakers.

Important note:

The M1 VINL must be protected from humidity – if the unit is moved from a cold place to a warm

room, leave the unit for an hour or so to allow sufficient time for the moisture to evaporate.

Please note: Musical Fidelity currently do not make any interconnecting cables, nor do we endorse any

particular manufacturer’s cables. If required, please refer to the Musical Fidelity dealer who can advise on

suitable quality cables for any particular setup.

Power Connections

The M1 ViNL is supplied with a standard IEC mains cable which plugs into the IEC socket at the back of the

unit. The unit features a universal power supply that can work anywhere in the world without reconfiguring.

Audio Connections

MM inputs: Connect left and right outputs from turntable/moving magnet cartridge to left and right MM input on

M1 ViNL. Use good quality fully shielded and connected (signal and ground) cables for optimum signal transfer

and minimum hum.

MC inputs: Connect left and right outputs from turntable/moving coil cartridge to left and right MC input on M1

ViNL. Use good quality fully shielded and connected (signal and ground) cables for optimum signal transfer and

minimum hum. If connecting a high output MC cartridge to the MC input results in a excessively high sound

output, it is perfectly in order to move it to the MM input and re-select input and loading options accordingly.

Make sure that the cartridge/turntable outputs are connected to the correct INPUTs for MM or MC. High

output MC cartridges are catered for in both MM and MC input options.

RCA Outputs: Connect left and right outputs to left and right line input on pre- or integrated amplifier. Use

good quality fully shielded and connected (signal and ground) coaxial cables for optimum signal transfer.

XLR (balanced) outputs: Connect left and right XLR outputs to left and right XLR line input on pre- or

integrated amplifier. Use good quality fully shielded and connected (signal and ground) XLR cables for optimum

signal transfer.

Trigger Connections

Trigger input: Connect system triggering device output to this socket. Use good quality 3.5mm mono jack

cable. Unit accepts 4.5V-15V DC triggering, either polarity.

Trigger output: Connect further devices in the system to be triggered into this socket. Use good quality 3.5mm

mono jack cable. Unit passes on +12V DC at up to 60mA, for further devices.

Earth Connection

The green earthing post should only be connected when excessive hum is experienced. Connect

the turntable earthing lead to this post if hum is noticed. If hum worsens when this post thus

connected, then disconnect immediately and investigate the cause elsewhere.

Note: some systems may have more than one direct earth point(s) already involved. This could cause

hum problems that may only become apparent on connecting in this unit. Thus the M1 ViNL may not be

the root cause of hum detected in a system.

There is no harm done if no connection is made to this terminal, as it is not always needed anyway, for

example, some turntables have their own earthing arrangement.

INSTALLATION

M1 ViNL manual issue 2.doc2 Page 7 of 12

2 3 4 5 6 7 8

1 DISPLAY LCD backlit black and white

2 POWER ON/STANDBY button

3 MM moving magnet selector button

4 MM-R MM load resistor selector button

5 MM-C MM load capacitor selector button

6 MC moving coil selector button

7 MC-R MC load resistor selector button

8 RIAA/IEC response selector button

10 11 12 13 14 15 16 17

9 EARTH 4mm banana post

10 MOVING MAGNET input left and right RCA

11 MOVING COIL input left and right RCA

12 XLR BALANCED OUTPUT right

13 SINGLE ENDED OUTPUT left and right RCA

14 XLR BALANCED OUTPUT left

15 TRIGGER IN 3.5mm jack input

16 TRIGGER OUT 3.5mm jack output

17 MAINS INPUT IEC socket

FACILITIES & CONNECTIONS

M1 ViNL manual issue 2.doc2 Page 8 of 12

Switch on and introduction.

Make sure the unit is fully connected up and plugged into the mains.

Check that the cartridge/turntable outputs are connected to the correct inputs (MM or MC) for the cartridge

being used.

The orange POWER/STBY LED will be lit indicating the presence of mains supply. Press the POWER/STBY

button on front panel.

The POWER/STBY LED will go out, and the display should light up and briefly show the product name.

Then the display reverts to the current phono option settings for the unit.

Please note: A great deal of effort has gone into making sure that the unit exhibits no loud noises through the

system during switching options or on/off. However, once installed into a hifi system, it is still a very high gain

(amplification) amplifier at the beginning of a high amplification chain. Therefore, cranking the main amplifier

volume to maximum and listening for clicks/thumps is neither recommended nor sensible. With this in mind, it is

strongly recommended that the option buttons are only pressed when the volume is turned down (or muted), to

avoid any accidental loud transients getting though to the speakers. Once options are set, the volume should

then be turned back to normal listening level.

Cartridge characteristics

For setting the various loading characteristics, the cartridge manufacturer’s data sheets or setup information

should be consulted.

In a lot of cases the settings are not critical, and may even be changed to suit personal preference, if any

audible differences are apparent.

No damage will normally occur to an “incorrectly” loaded cartridge; at very worse a slightly impaired or non-

optimal frequency response and/or increased distortion may result.

M1 ViNL

Cartridge - MM

RIAA 47K 50pF

OPERATION

M1 ViNL manual issue 2.doc2 Page 9 of 12

Choosing cartridge type

Select the cartridge being used by pressing the MM or MC button. The display shows current selection and the

correct input sockets are automatically switched in.

RIAA and RIAA/IEC

This setting is common to both MM and MC cartridge types.

The -IEC option alters the normal RIAA frequency response by rolling off (reducing) the output at very low

frequencies i.e. around 20Hz and below. See chart on P.11 for more information.

This can help to prevent distortion and/or overload of subsequent amplifier/speaker systems by low frequency

artefacts such as record warp, surface noise or rumble.

Press the RIAA/IEC button to select IEC response. The display will indicate “IEC” to show that the IEC roll-off is

implemented. Press RIAA/IEC button again to display “RIAA” and the output response is now without roll-off.

MM loading resistor selection

The load resistor for MM cartridge is selected by pressing MM-R button. There are two options available, 47K

(47,000 ohms, or 47K) or 68K.

Press the MM-R button to select 68K. Press MM-R button again to revert to 47K. Choose the option

recommended by the cartridge manufacturer. If no recommendation is apparent, start by using the 47K option.

MM loading capacitor selection

The load capacitor for MM cartridge is selected by pressing MM-C button. There are 8 options available, 50pF

(pico-farads), 100pF, 150pF, 200pF, 250pF, 300pF, 350pF, 400pF.

Use the MM-C button to cycle through the options, until the closest one to the cartridge manufacturer’s

recommendation is displayed. If no recommendation is apparent, start by using the 50pF option.

MC loading resistor selection

The load resistor for MC cartridge is selected by pressing MC-R button. There are 10 options available, 10R

(also written as 10or 10 ohms), 18R, 25R, 50R, 100R, 200R, 400R, 800R, 1600R, or 47K (also written as

47,000 or ohms).

Use the MC-R button to cycle through the options, until the closest one to the cartridge manufacturer’s

recommendation is displayed. If no recommendation is apparent, start by using the 1600R option.

There is a 47K setting in MC which is recommended for the higher output type MC cartridges giving out approx

1mV or more. If, however, connecting a high output MC cartridge to the MC input results in a excessively high

sound output, it is perfectly in order to move it to the MM input and select input and loading options accordingly.

Note: The MC input capacitor is fixed and cannot be changed. This capacitor does not affect loading at

such low impedances.

Trigger input and output

The unit can be triggered to switch on or off remotely by applying a ±4.5 to ±15V DC signal to the 3.5mm (”)

TRIGGER INPUT from an external triggering device. Any further devices to be triggered on/off may be

connected to the TRIGGER OUTPUT jack as it replicates the TRIGGER INPUT signal. This will form a chain of

devices that will switch on and off together. N.B. the on/off triggering action works from ANY device in the

chain, whether at the beginning, middle or end of the chain.

Cartridge - MC

RIAA 100R 470pF

Cartridge - MM

RIAA 47K 400pF

Cartridge - MM

RIAA 68K 50pF

Cartridge - MM

IEC 47K 50pF

OPERATION

M1 ViNL manual issue 2.doc2 Page 10 of 12

Basic problem-solving with an amplifier is similar to troubleshooting other electrical or electronic equipment.

Always check the most obvious possible causes first, such as the following examples:

Problem Probable Cause Remedy

No power Mains power supply is not fully inserted

into mains socket

Mains power supply lead is not fully

inserted into rear socket

Plug in securely

No sound Wrong connections between input

sources and the unit

Cartridge incorrectly wired

Check audio input and output lead

connections

Check cartridge wiring

Sound too quiet/loud Cartridge/turntable outputs in wrong input Use MM input for MM cartridges;

MC input for MC cartridges.

Sound is not precise, lacking in

bass and stereo image

Cartridge incorrectly wired

Input connector plugs not fully pushed in

Output connector plugs not fully pushed in

Double-check cartridge wiring using

cartridge and turntable

manuals/wiring diagrams.

Check plugs are inserted fully and

securely

Hum Turntable not earthed or needs earthing

Turntable already earthed and earthing

further creates hum loop in system

Earth loops already in system

Audio connector plug not fully pushed in

Cable fault

Unsuitable Cable

(e.g. cable grounds not connected)

Check turntable earthing lead is

connected to earthing post on M1

ViNL.

Disconnect earthing lead from

earthing post.

Investigate for earth loops

elsewhere in system.

Insert plug securely

Check cable is connected at both

ends.

N.B. some esoteric cables have

internal wiring intentionally

disconnected/modified. For best

results on all inputs AND outputs,

please use good quality screened

coax; fully connected signal-to

signal, screen-to-screen.

Plop or click heard in speakers

when switching on or off or

changing options

High gain of M1 ViNL, amplifying normal

circuit transients.

Not a fault. It is recommended that

the volume level on amplifier is

turned down if switching the M1

ViNL on or off; or pressing option

switches whilst connected.

Distorted sound

Cartridge and/or tone arm not aligned

properly

Cartridge fault or worn needle

Dirt on record

Carefully follow turntable

instructions to correctly re-align

tone arm and cartridge.

Replace needle or cartridge.

Clean dust and dirt from record

Distorted and loud sound Line outputs of M1 ViNL plugged into

PHONO amplifier inputs of following

amplifier

Use LINE level inputs only, e.g. an

AUX input, for the outputs of the M1

ViNL.

If none of these actions affect a cure, please contact the dealer, or an authorised Musical Fidelity service agent.

Remember; never open the case of the M1 ViNL, as this will invalidate the guarantee.

PROBLEMS?

Andere Handbücher für MM/MC PHONO STAGE M1 VINL

Inhaltsverzeichnis

Andere Musical Fidelity Verstärker Handbücher

Musical Fidelity

Musical Fidelity M5si Bedienungsanleitung

Musical Fidelity

Musical Fidelity A308 CR Bedienungsanleitung

Musical Fidelity

Musical Fidelity SUPERCHARGER 750K Bedienungsanleitung

Musical Fidelity

Musical Fidelity V90-AMP Bedienungsanleitung

Musical Fidelity

Musical Fidelity MERLIN Bedienungsanleitung

Musical Fidelity

Musical Fidelity A3.5 Bedienungsanleitung

Musical Fidelity

Musical Fidelity F2 Bedienungsanleitung

Musical Fidelity

Musical Fidelity F225 Bedienungsanleitung

Musical Fidelity

Musical Fidelity A1 Integrated Bedienungsanleitung

Musical Fidelity

Musical Fidelity M1HPA Bedienungsanleitung

Musical Fidelity

Musical Fidelity LX2-LPS Bedienungsanleitung

Musical Fidelity

Musical Fidelity Electra E20 Bedienungsanleitung

Musical Fidelity

Musical Fidelity M1 HPAP Bedienungsanleitung

Musical Fidelity

Musical Fidelity A3.2 CR Bedienungsanleitung

Musical Fidelity

Musical Fidelity NU-VISTA Series Bedienungsanleitung

Musical Fidelity

Musical Fidelity AMS35i ANTONY MICHAELSON Bedienungsanleitung

Musical Fidelity

Musical Fidelity kW Phono Bedienungsanleitung

Musical Fidelity

Musical Fidelity M3si Bedienungsanleitung

Musical Fidelity

Musical Fidelity LX2-HPA Bedienungsanleitung

Musical Fidelity

Musical Fidelity X-LPSV8 Bedienungsanleitung

Musical Fidelity

Musical Fidelity X-AS100 Bedienungsanleitung

Musical Fidelity

Musical Fidelity M8xi Bedienungsanleitung

Musical Fidelity

Musical Fidelity M8 500S Bedienungsanleitung

Musical Fidelity

Musical Fidelity X-LPS V3 Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung