Mustek POWERMUST 1008 ONLINE LCD Bedienungsanleitung

PowerMust

1008 Online LCD & RM

PowerMust

2016 Online LCD & RM

PowerMust

3024 Online LCD & RM

Online UPS

User Manual

Table of Contents

1. Important Safety Warning………………………………………………

1-1. Transportation 2

1-2. Preparation 2

1-3. Installation 2

1-4. Operation 2

1-5. Maintenance, service and faults 3

2. Installation and setup……………………………………………………

2-1. Rear panel view 4

2-2. etup the UP 5

3. Operations…………………………………………………………………..

3-1. Button operation 7

3-2. LCD Panel 7

3-3. Audible Alarm 9

3-4. LCD display wordings index 9

3-5. UP etting 9

3-6. Operating Mode Description 12

3-7. Faults Reference Code 12

3-8. Warning indicator 13

. Troubleshooting…………………………………………………………...

5. Storage and Maintenance……………………………………………….

6. Specifications……………………………………………………………… 16

1. Important Safety Warning

Please comply with all warnings and operating instructions in this manual strictly. ave this

manual properly and read carefully the following instructions before installing the unit. Do not

operate this unit before reading through all safety information and operating instructions carefully

1-1. Transportation

Please transport the UP system only in the original package to protect against shock

and impact.

1-2. Preparation

Condensation may occur if the UP system is moved directly from cold to warm

environment. The UP system must be absolutely dry before being installed. Please

allow at least two hours for the UP system to acclimate the environment.

Do not install the UP system near water or in moist environments.

Do not install the UP system where it would be exposed to direct sunlight or near

heater.

Do not block ventilation holes in the UP housing.

1-3. Installation

Do not connect appliances or devices which would overload the UP system (e.g. laser

printers) to the UP output sockets.

Place cables in such a way that no one can step on or trip over them.

Do not connect domestic appliances such as hair dryers to UP output sockets.

The UPS can be operated by any individuals with no previous experience.

Connect the UP system only to an earthed shockproof outlet which must be easily

accessible and close to the UP system.

Please use only VDE-tested, CE-marked mains cable (e.g. the mains cable of your

computer) to connect the UP system to the building wiring outlet (shockproof outlet).

Please use only VDE-tested, CE-marked power cables to connect the loads to the UP

system.

When installing the equipment, it should ensure that the sum of the leakage current of

the UP and the connected devices does not exceed 3.5mA.

1- . Operation

Do not disconnect the mains cable on the UP system or the building wiring outlet

(shockproof socket outlet) during operations since this would cancel the protective

earthing of the UP system and of all connected loads.

The UP system features its own, internal current source (batteries). The UP output

sockets or output terminals block may be electrically live even if the UP system is not

connected to the building wiring outlet.

In order to fully disconnect the UP system, first press the OFF/Enter button to

disconnect the mains.

Prevent no fluids or other foreign objects from inside of the UP system.

1-5. Maintenance, service and faults

The UP system operates with hazardous voltages. Repairs may be carried out only by

qualified maintenance personnel.

Caution - risk of electric shock. Even after the unit is disconnected from the mains

(building wiring outlet), components inside the UP system are still connected to the

battery and electrically live and dangerous.

Before carrying out any kind of service and/or maintenance, disconnect the batteries

and verify that no current is present and no hazardous voltage exists in the terminals of

high capability capacitor such as BU -capacitors.

Only persons are adequately familiar with batteries and with the required precautionary

measures may replace batteries and supervise operations. Unauthorized persons must

be kept well away from the batteries.

Caution - risk of electric shock. The battery circuit is not isolated from the input voltage.

Hazardous voltages may occur between the battery terminals and the ground. Before

touching, please verify that no voltage is present!

Batteries may cause electric shock and have a high short-circuit current. Please take the

precautionary measures specified below and any other measures necessary when

working with batteries:

remove wristwatches, rings and other metal objects

use only tools with insulated grips and handles.

When changing batteries, install the same number and same type of batteries.

Do not attempt to dispose of batteries by burning them. This could cause battery

explosion.

Do not open or destroy batteries. Escaping electrolyte can cause injury to the skin and

eyes. It may be toxic.

Please replace the fuse only with the same type and amperage in order to avoid fire

hazards.

Do not dismantle the UP system.

2. Installation and setup

NOTE: Before installation, please inspect the unit. Be sure that nothing inside the package is

damaged. Please keep the original package in a safe place for future use.

NOTE: There are two different types of online UP : standard and long-run models. Please refer

to the following model table.

Model Type Model Type

PowerMust 1008 Online

LCD

PowerMust 1008L Online

LCD

PowerMust 2016 Online

LCD

PowerMust 2016L Online

LCD

PowerMust 3024 Online

LCD

tandard

PowerMust 3024L Online

LCD

Long-run

2-1. Rear panel view

PowerMust 1008(L) Online LCD

PowerMust 2016(L) Online LCD

PowerMust 3024(L) Online LCD

PowerMust 1008(L) Online LCD

PowerMust 2016(L) Online LCD

PowerMust 3024(L) Online LCD

1. Programmable outlets: connect to non-critical loads.

2. Output receptacles: connect to mission-critical loads.

3. AC input

4. Input circuit breaker

5. Network/Fax/Modem surge protection

6. Emergency power off function connector (EPO)

7. U B communication port

8. R -232 communication port

9. NMP intelligent slot

10.External battery connection (only available for L model)

11.Output terminal

12.Output circuit breaker

2-2. Setup the UPS

Step 1: UPS input connection

Plug the UP into a two-pole, three-wire, grounded receptacle only. Avoid using extension cords.

For 208/220/230/240VAC models:

The power cord is supplied in the UP package.

For 110/115/120/127VAC models: The power cord is attached to the UP . The input plug is a

NEMA 5-15P for 1008(L) models, NEMA 5-20P for 2016(L) models.

Note:

For Low voltage models

: Check if the site wiring fault indicator lights up in LCD panel. It will

be illuminated when the UP is plugged into an improperly wired utility power outlet (Refer to

Troubleshooting section).

Step 2: UPS output connection

For socket-type outputs, there two kinds of outputs: programmable outlets and general

outlets. Please connect non-critical devices to the programmable outlets and critical devices

to the general outlets. During power failure, you may extend the backup time to critical

devices by setting shorter backup time for non-critical devices.

For terminal-type input or outputs, please follow below steps for the wiring configuration:

a) Remove the small cover of the terminal block

b) uggest using AWG14 or 2.1mm

power cords. uggest using WG12-10 or

3.3mm

-5.3mm

power cords for NEMA type.

c) Upon completion of the wiring configuration, please check whether the wires are securely

affixed.

d) Put the small cover back to the rear panel.

Step 3: Communication connection

Communication port:

USB port RS-232 port Intelligent slot

To allow for unattended UP shutdown/start-up and status monitoring, connect the

communication cable one end to the U B/R -232 port and the other to the communication port

of your PC. With the monitoring software installed, you can schedule UP shutdown/start-up and

monitor UP status through PC.

The UP is equipped with intelligent slot perfect for either NMP or A 400 card. When installing

either NMP or A 400 card in the UP , it will provide advanced communication and monitoring

options.

PS. USB port and RS-232 port can’t work at the same time.

Step : Network connection

Network/Fax/Phone surge port

Connect a single modem/phone/fax line into surge-protected “IN” outlet on the back panel of the

UP unit. Connect from “OUT” outlet to the equipment with another modem/fax/phone line cable.

Step 5: Disable and enable EPO function

Keep the pin 1 and pin 2 closed for UP normal operation. To activate EPO function, cut the wire

between pin 1 and pin 2.

Step 6: Turn on the UPS

Press the ON/Mute button on the front panel for two seconds to power on the UP .

Note: The battery charges fully during the first five hours of normal operation. Do not expect

full battery run capability during this initial charge period.

Step 7: Install software

For optimal computer system protection, install UP monitoring software to fully configure UP

shutdown. You may insert provided CD into CD-ROM to install the monitoring software. If not,

please follow steps below to download and install monitoring software from the internet:

1. Go to the website http://www.power-software-download.com

2. Click ViewPower software icon and then choose your required O to download the software.

3. Follow the on-screen instructions to install the software.

4. When your computer restarts, the monitoring software will appear as an orange plug icon

located in the system tray, near the clock.

Step 8: External battery connection (for long-run models only)

Follow below chart to make external

battery connection.

It’s in closed status for UP

normal operation.

3. Operations

3-1. Button operation

Button Function

ON/Mute Button

Turn on the UP : Press and hold ON/Mute button for at least 2 seconds

to turn on the UP .

Mute the alarm: When the UP is on battery mode, press and hold this

button for at least 5 seconds to disable or enable the alarm system. But

it’s not applied to the situations when warnings or errors occur.

Down key: Press this button to display previous selection in UP setting

mode.

witch to UP self-test mode: Press ON/Mute buttons simultaneously

for 5 seconds to enter UP self-testing while in AC mode, ECO mode, or

converter mode.

OFF/Enter Button

Turn off the UP : Press and hold this button at least 2 seconds to turn

off the UP in battery mode. UP will be in standby mode under power

normal or transfer to Bypass mode if the Bypass enable setting by

pressing this button.

Confirm selection key: Press this button to confirm selection in UP

setting mode.

elect Button

witch LCD message: Press this button to change the LCD message for

input voltage, input frequency, battery voltage, output voltage and

output frequency. It will return back to default display when pausing for

10 seconds.

etting mode: Press and hold this button for 5 seconds to enter UP

setting mode when UP is in standby mode or bypass mode.

Up key: Press this button to display next selection in UP setting mode.

ON/Mute + elect

Button

witch to bypass mode: When the main power is normal, press

ON/Mute and elect buttons simultaneously for 5 seconds. Then UP

will enter to bypass mode. This action will be ineffective when the input

voltage is out of acceptable range.

3-2. LCD Panel

Display Function

Backup time information

Indicates the backup time in pie chart.

Indicates the backup time in numbers.

H: hours, M: minute, : second

Fault information

Indicates that the warning and fault occurs.

Indicates the warning and fault codes, and the codes are listed in

details in 3-5 section.

Mute operation

Indicates that the UP alarm is disabled.

Output & Battery voltage information

Indicates the output voltage, frequency or battery voltage.

Vac: output voltage, Vdc: battery voltage, Hz: frequency

Load information

Indicates the load level by 0-25%, 26-50%, 51-75%, and 76-

100%.

Indicates overload.

Indicates the load or the UP output is short circuit.

Programmable outlets information

Indicates that programmable management outlets are working.

Mode operation information

Indicates the UP connects to the mains.

Indicates the battery is working.

Indicates the bypass circuit is working.

Indicates the ECO mode is enabled.

Indicates the Inverter circuit is working.

Indicates the output is working.

Battery information

Indicates the Battery level by 0-25%, 26-50%, 51-75%, and

76-100%.

Indicates the battery is fault.

Indicates low battery level and low battery voltage.

Input & Battery voltage information

Indicates the input voltage or frequency or battery voltage.

Vac: Input voltage, Vdc: battery voltage, Hz: input frequency

Andere Handbücher für POWERMUST 1008 ONLINE LCD

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Mustek UPS Handbücher

Mustek

Mustek POWERMUST 636 Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Mustek

Mustek POWERMUST 400 USB Bedienungsanleitung

Mustek

Mustek PM 6000 Bedienungsanleitung

Mustek

Mustek POWERMUST 636 Bedienungsanleitung

Mustek

Mustek POWERMUST 800 USB Bedienungsanleitung

Mustek

Mustek POWER MUST 424 Installations- und Betriebshandbuch

Mustek

Mustek PowerMust 600 LCD Installations- und Betriebshandbuch

Mustek

Mustek POWERMUST 650 OFFICE Bedienungsanleitung

Mustek

Mustek PowerMust 6054 LCD Bedienungsanleitung

Mustek

Mustek PowerMust 600 LED Bedienungsanleitung

Mustek

Mustek POWERMUST 424 OFFLINE Bedienungsanleitung

Mustek

Mustek PowerMust 3000 On Line(3K) Bedienungsanleitung

Mustek

Mustek PM 600 PLUS Bedienungsanleitung

Mustek

Mustek POWERMUST 600 USB - Bedienungsanleitung

Mustek

Mustek PowerMust 424 LCD Installations- und Betriebshandbuch

Mustek

Mustek POWERMUST 6048 ONLINE LCD Bedienungsanleitung

Mustek

Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch

Mustek

Mustek Power Must 400 Bedienungsanleitung

Mustek

Mustek POWERMUST 1060 Installations- und Betriebshandbuch

Mustek

Mustek PowerMust 1513S NetGuard (1500VA) Bedienungsanleitung

Mustek

Mustek POWERMUST 424 Installations- und Betriebshandbuch

Mustek

Mustek Power Must 400 Bedienungsanleitung

Beliebte UPS Handbücher anderer Marken

Pylontech

Pylontech Victron & Pylontech US5000 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung

Emerson

Emerson Liebert NXL series Bedienungsanleitung

MAKELSAN

MAKELSAN BOXER SERIES Bedienungsanleitung

Block

Block PC-0524-400-0 Bedienungsanleitung

CyberPower

CyberPower CP585LCD Bedienungsanleitung

Eaton

Eaton 3S Montageanleitung

CyberPower

CyberPower Office Tower Series UPS 1000 Bedienungsanleitung

CyberPower

CyberPower BM100 Bedienungsanleitung

Best Power

Best Power 610 Bedienungsanleitung

Best Power

Best Power Unity/I UT3K Bedienungsanleitung

Xantrex

Xantrex Trace 512 UR-UPS Bedienungsanleitung

Forza

Forza SL-1501UL Bedienungsanleitung

LEGRAND

LEGRAND keor 310081 Bedienungsanleitung

ABB

ABB Conceptpower DPA 500 Bedienungsanleitung

ZincFive

ZincFive BC Series Bedienungsanleitung

BPC

BPC 1.5K SMART Bedienungsanleitung

Dynex

Dynex DX-800U Bedienungsanleitung