Mustek PowerMust 1513S NetGuard (1500VA) Bedienungsanleitung

USER MANUAL

Line Interactive UPS

PowerMust 1513S NetGuard (1500VA), Line Int., IEC

PowerMust 2018S NetGuard (2000VA), Line Int., IEC

PowerMust 3027S NetGuard (3000VA), Line Int., IEC

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

This manual contains important instructions for

1500VA/2000VA/3000VA series that should be followed during

installation and maintenance of the UPS and batteries. Please read all

safety and operating instructions before operating the UPS. Adhere to

all warnings on the unit and in this manual. And follow all operating

and user instructions.

Warranty & Service Information

Thanks for buying this Mustek UPS product.

Please follow the instructions in the product manual and if applicable the

software installation manual, to have the maximum use of your product.

Installing the software:

If you products comes with software you will find a CD Rom in the box

containing the software.

Please follow the instructions when installing the software.

You can download the software, manual and short reference manual at the

following site: www.ups-software-download.com

Warranty:

As a manufacturer we provide a minimum of 1 year warranty on our product.

However for the exact warranty period and the warranty terms you should

contact your reseller as both the warranty period and the terms may vary per

Country / Region.

Problem solving:

Please check the chapter in your manual ( hardware and software) on problem

solving.

Additionally:

Please check our website (www. Mustek.eu) regularly for updates of the

software as well as Frequent Asked Questions (FAQ) .

If this not solve your problem please contact your reseller for advice.

Service and Maintenance:

If the product requires service or maintenance in the warranty period always

contact your reseller for the procedures. If outside the warranty period we

advise you the contact your reseller as well. In any case always make sure that

service or maintenance on the product are performed by a qualified technician.

CONTENT:

USER MANUAL ·············································································· 0

1. INTRODUCTION·········································································· 1

2. SAFETY WARNING······································································· 1

2.1

ESCRIPTION OF

OMMONLY

SED

YMBOLS

······································· 2

3. INSTALLATION ··········································································· 3

3.1

NSPECTION OF

NIT

···································································· 3

3.2

NPACKING THE

ABINET

······························································ 3

3.3

UPS

ETUP

··············································································· 3

4. OPERATION················································································ 4

4.1

ISPLAY

ANEL

·········································································· 4

4.2

PERATING

ODE

······································································· 7

4.3

ONFIGURING

OAD

EGMENT

························································ 7

4.4

ONFIGURING

REEN

UNCTION

······················································ 8

5. COMMUNICATION PORT ····························································· 8

5.1

RS-232

AND

USB

OMMUNICATION

ORTS

·········································· 8

5.2

MERGENCY

OWER

(EPO)······················································· 9

5.3

ETWORK

ANAGEMENT

ARD

PTIONAL

)········································ 9

6. UPS MAINTENANCE ··································································· 10

6.1

UPS

AND

ATTERY

ARE

······························································ 10

6.2

TORING THE

UPS

AND

ATTERIES

··················································· 10

6.3

IME TO

EPLACE

ATTERIES

························································· 10

6.4

EPLACING

UPS

NTERNAL

ATTERIES

·············································· 11

6.5

ESTING

ATTERIES

····························································· 11

6.6

ECYCLING THE

SED

ATTERY

:····················································· 12

7. SPECIFICATION ········································································· 12

7.1

PECIFICATION

·········································································· 12

7.2

EAR

ANELS

··········································································· 13

8. TROUBLE SHOOTING ································································· 14

8.1

UDIBLE

LARM

ROUBLE

HOOTING

·············································· 14

8.2

ENERAL

ROUBLE

HOOTING

······················································· 14

9. SOFTWARE INSTALLATION························································· 15

1. Introduction

This line-interactive series is compact and pure sine wave UPS and it is designed for

essential applications and environment, such as desktops, servers, workstations, and

other networking equipments. These models are available in the output ratings of

1500VA, 2000VA and 3000VA. The series protects your sensitive electronic equipments

against power problems including power sags, spike, brownouts, line noise and

blackouts.

The series is convertible to rack and tower forms. It can be placed either in Rack 2U or

Tower form. The front panel of the UPS includes LCD display and four control buttons

that allow users to monitor, configure and control the units. On LCD, it also includes a

LCD graphical bar, two status indications and four alarm indications. A control button

from the front panel allows users to silence off the AC fail alarm and initiate the UPS

self-test sequence as well. The UPS case for 1500VA ~ 3000VA is made of metal. This

series is powered from the AC mains and supply AC outputs via receptacles on the rear

panel. Communication and control of UPS is available through serial or USB ports

located on the rear panel. The serial port will support communications directly with a

server.

Features:

Microprocessor control guarantees high reliability

High frequency design

Built-in boost and buck AVR

Easy battery replacement design

Selectable input and output range

Cold start capability

Built-in Dry contact/RS-232/USB communication port

SNMP allows for web-based remote or monitoring management

Overload, short-circuit, and overheat protection

Rack/Tower 2 in 1 Design

19 inches rack mount available for all models

2. Safety Warning

DANGER:

This UPS contains high voltages. All repairs and service should be performed by

authorized service personnel only. There are no user serviceable parts inside the UPS.

WARNING:

This UPS contains its own energy source (batteries).The UPS output may carry

live voltage even when the UPS is not connected to an AC supply.

To reduce the risk of fire or electric shock, install this UPS in a temperature and

humidity controlled, indoor environment, free of conductive

contaminants.(Ambient :0-40°C)

To reduce the risk of fire, connect to a circuit breaker provided with 20 amperes

maximum branch circuit over-current protection.

To comply with international standards and wiring regulations, the sum of the

leakage currents of the UPS and the connected loads must not exceed 3.5mA.

The socket outlet that supplies the UPS shall be installed near the UPS and shall

be easily accessible.

Protective earthling connections shall be such that disconnection of a protective

earth should be made at one point that is the furthest away from the UPS,

maintaining the dedicated line in order to secure equipotential connection.

CAUTION:

Batteries can present a risk of electrical shock or burnt from high short-circuit

current. Observe proper precautions. Servicing should be performed by qualified

service personnel knowledgeable of batteries and required precautions. Keep

unauthorized personnel away from batteries.

Proper disposal of batteries is required. Refer to your local codes for disposal

requirements.

Never dispose of batteries in a fire. Batteries may explode when exposed to

flame.

Following figure shows the basic internal circuit configuration of the UPS

2.1 Description of Commonly Used Symbols

Some or all of the following Notations may be used in this manual and may appear in

your application process. Therefore, all users should be familiar with them and

understand their explanations.

Table1. Description of Commonly Used Symbols

Symbol Description Symbol Description

Alert you to pay special attention

Protective ground

Caution of high voltage

Recycle

Alternating current source (AC)

Keep UPS in a clear area

Direct current source(DC)

3. Installation

3.1 Inspection of Unit

Inspect the UPS upon receiving. If the UPS is apparently damaged during the shipment,

please keep the box and packing material in original form for the carrier and notify the

carrier and dealer immediately.

3.2 Unpacking the Cabinet

To unpack the system:

1. Open the outer carton and remove the accessories packaged with the cabinet.

2. Carefully lift the cabinet out of the outer carton and set it on a flat, stable surface.

3. Discard or recycle the packaging in a responsible manner, or store it for future use.

3.3 UPS Setup

All model series are designed for tower and rack purpose. They can be installed into a

19 inches equipment rack. Please follow the instruction for Tower Setup and

Rack-Mount Setup.

Tower setup

This series of UPS can be placed horizontally and vertically. As a tower configuration, it

is provided with the optional UPS stands to stabilize the UPS when the UPS is

positioned in vertical. The UPS stand must be attached to the bottom of the tower.

Use the following procedure to install UPS in UPS stands.

1. Slide down the UPS vertically and put two UPS stands at the end of the tower (Fig 1).

2. Place down the UPS into two stands carefully (Fig 2).

3. Pull out the LCD box and rotate it in a clockwise direction to 90 degree and then push

it back in the front panel (Fig 3).

Fig 1 Fig 2 Fig 3

Rack-mount setup

The series can be installed in 19 inches racks. Both the UPS and external battery

enclosure need 2U of valuable rack space.

Use the following procedure to install UPS in a rack.

1. Align the mounting ears with screw holes on the side of the UPS, and tighten the

screw. (Fig 4)

2. Assemble the rack rails with the rack-mounting. (Fig 5)

Fig 4 Fig 5

3. Slide in the UPS into the rack rail and lock it in the rack enclosure. (Fig 6)

4. Tighten the screw, and the load can then be connected. (Fig 7)

Fig 6 Fig 7

4. Operation

4.1 Display Panel

The UPS has a four-button graphical LCD with dual color backlight. Standard back-light

is used to light up the display with black text and a blue background. When the UPS has

a critical alarm, the backlight changes the background to red. See Figure below:

Control Buttons functions:

Table2. Description of control button

Control

Button Switch Function

ON/OFF

--To turn on/off the UPS

Press and hold the button more than 3 seconds.

--To release the UPS from faulty mode

Cut off input power and then press and hold the button

more than 2 seconds to shut down the UPS.

UPS Test

Alarm Silence

--To perform basic function test

Press and hold the button for 3 seconds.

--To perform Battery life test

Press and hold the button for 10 seconds.

-- To disable alarm buzzer

Press the button for one second.

Select

Press the Select button

to select the settings

value one by one

Enter

-- Enter settings mode

Press and hold the button more than 3 seconds.

-- Enter settings item

Press and hold the Enter button more than one

second, the UPS allows users to configure the settings,

and the settings string will flash.

-- Confirm settings

Press and hold the Enter button for one second.

-- Exit Settings mode

Press and hold the Enter button for 3 seconds or

button for 0.5 second.

Note: Ensure the battery is fully charged during line mode when conducting functional

tests.

Note: A list of events shown as below is not able to disable alarm buzzer:

Low Battery, Fan Failed, Fan Fault Time Out, and Overheat.

Note: User can disable the alarm buzzer when it’s sounding, but an alarm will still sound

when a new alarm event is encountered.

LCD display functions:

The following table describes the functions of the LCD display.

Table3. Description of LCD display function

No. Description Function

Input frequency and

voltage Indicate the value of input frequency and voltage

Input plug indicator Light on when the input power is at no loss.

Output frequency

and

voltage Indicate the value of output frequency and voltage

Output plug indicator

The UPS has two groups of outlets. The output plug

indicator will light on if there is output power

respectively.

UPS status/user

setting display String

Strings Indicate the UPS status( see Table 4)

Strings Indicate user setting options( see Table 5)

Warning indication Light on when the UPS is failure or alarm.

Settings Light on when the UPS under settings mode.

Battery

volume

level

display

Indicate the amount of battery volume remaining.

Each battery volume level bar indicates a 20% of total

battery volume

Load

capacity

level

display

Indicate the percentage of UPS load capacity which is

being used by the protected equipment. Each LCD

level bar indicates a 20% of the total UPS output

capacity.

UPS Status Display String Description:

The following table shows the description of the LCD display string:

Table4. UPS Status Display String

LCD Display String Description

STbY UPS work at Standby mode

IPVL Input voltage is too low

IPVH Input voltage is too high

IPFL Input frequency is too low

IPFH Input frequency is too high

NORM UPS work at Line mode

AVR UPS work at AVR mode

bATT UPS work at Battery mode

TEST UPS work at battery life/function test mode

OPVH Battery mode, the output is too high

OPVL The output is too low

OPST Output short

OVLD Overload

bATH Battery voltage is too high

bATL Battery voltage is too low

OVTP Internal temperature is too high

FNLK Fan is locked

bTWK Batteries are weak

User Setting String Description:

The following table shows the options that can be changed by user.

Table5. User Setting String

OPV Output voltage mode select

[220]= 220V

[230]= 230V

[240]= 240V

AVR Input type select

[000]= Normal range mode

[001]= Wide range mode

[002]= Generator mode

EbM External battery module

(EBM)

0~9 is the number of external battery

module

TEST Auto self-test [000]=Disable [001]=Enable

AR Automatic restart [000]=Disable [001]=Enable

GF Green function [000]=Disable [001]=Enable

bZ Buzzer control [000]=Disable [001]=Enable

LS1 Load segment 1 [000]=Turn off [001]=Turn on

LS2 Load segment 2 [000]=Turn off [001]=Turn on

4.2 Operating Mode

Normal range mode: Under Input mode the UPS accepts AC input voltage range for

+/-20%.

Generator mode: Under generator mode, the low frequency transfer point can go as low

as 40Hz and as high as 80Hz before being transferred to battery mode.

Wide range mode: Under Input settings mode, the UPS accepts AC input voltage

range for -30% ~ +20%.

Battery mode

When the UPS is operating during a power outage, the alarm beeps once every four

seconds and the LCD display string shows “bATT” to indicate the UPS work at battery

mode.

If battery volume becomes low while in Battery mode, the alarm beeps once every

second and the LCD display string shows “bATL”.

Standby mode

When the UPS is turned off and remains plugged into a power outlet, the UPS is on

Standby mode. The LCD display string shows “STbY” to indicate that power is not

available to your equipment. The battery recharges when necessary.

4.3 Configuring Load Segment

Load segment are sets of receptacles that can be controlled through the display. Each

UPS has two configurable load segments. See “Rear Panels” on page 30 for load

segment for each UPS model.

Note: This configuring can be operated when UPS is power on.

1K model has only one load segment, cannot configure.

To configure the load segment through the display:

4.3.1 Enter settings mode: Press and hold the Enter button more than 3 seconds.

Then UPS will transfer to setting mode.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Mustek UPS Handbücher

Mustek

Mustek PM 600 PLUS Bedienungsanleitung

Mustek

Mustek POWER MUST 424 Installations- und Betriebshandbuch

Mustek

Mustek PowerMust 6054 LCD Bedienungsanleitung

Mustek

Mustek PowerMust 600 LCD Installations- und Betriebshandbuch

Mustek

Mustek POWERMUST 1008 ONLINE LCD Bedienungsanleitung

Mustek

Mustek POWERMUST 636 Bedienungsanleitung

Mustek

Mustek POWERMUST 424 Installations- und Betriebshandbuch

Mustek

Mustek Power Must 400 Bedienungsanleitung

Mustek

Mustek POWERMUST 424 OFFLINE Bedienungsanleitung

Mustek

Mustek PowerMust 424 LCD Installations- und Betriebshandbuch

Mustek

Mustek POWERMUST 6048 ONLINE LCD Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Mustek

Mustek PowerMust 600 LED Bedienungsanleitung

Mustek

Mustek POWERMUST 1060 Installations- und Betriebshandbuch

Mustek

Mustek POWERMUST 636 Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Mustek

Mustek Power Must 400 Bedienungsanleitung

Mustek

Mustek PM 6000 Bedienungsanleitung

Mustek

Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch

Mustek

Mustek POWERMUST 600 USB - Bedienungsanleitung

Mustek

Mustek POWERMUST 800 USB Bedienungsanleitung

Mustek

Mustek POWERMUST 650 OFFICE Bedienungsanleitung

Mustek

Mustek PowerMust 3000 On Line(3K) Bedienungsanleitung

Mustek

Mustek POWERMUST 400 USB Bedienungsanleitung

Beliebte UPS Handbücher anderer Marken

Pylontech

Pylontech Victron & Pylontech US5000 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung

Emerson

Emerson Liebert NXL series Bedienungsanleitung

MAKELSAN

MAKELSAN BOXER SERIES Bedienungsanleitung

Block

Block PC-0524-400-0 Bedienungsanleitung

CyberPower

CyberPower CP585LCD Bedienungsanleitung

Eaton

Eaton 3S Montageanleitung

CyberPower

CyberPower Office Tower Series UPS 1000 Bedienungsanleitung

CyberPower

CyberPower BM100 Bedienungsanleitung

Best Power

Best Power 610 Bedienungsanleitung

Best Power

Best Power Unity/I UT3K Bedienungsanleitung

Xantrex

Xantrex Trace 512 UR-UPS Bedienungsanleitung

Forza

Forza SL-1501UL Bedienungsanleitung

LEGRAND

LEGRAND keor 310081 Bedienungsanleitung

ABB

ABB Conceptpower DPA 500 Bedienungsanleitung

ZincFive

ZincFive BC Series Bedienungsanleitung

BPC

BPC 1.5K SMART Bedienungsanleitung

Dynex

Dynex DX-800U Bedienungsanleitung