MUTOH ValueJet 1324 Bedienungsanleitung

June 2018

VJ1324E-A-04c 1 MUTOH INDUSTRIES LTD.

Some contents of the Operation Manual are changed. Please see the following list.

The content of this documents are based on the specification of the firmware Ver.3.04 or later.

Chapter Item Description Revision

Chapter

3.5.1 “Nozzle check” The printer information (date and time of

printing, printer’s serial number, firmware

version) is printed on the nozzle check

pattern.

04c

Changed the adjustment method

in “3.6 Adjust Print”

Refer to sheet 2 04b

Chapter

Changed the adjustment method

in “4.2.6. Media feed

compensation”

Refer to sheet 3-4 04b

Chapter

Added the menu in ”5.1.1.1 User

Type menu”

Refer to sheet 5 04b

Added “5.1.1.1.9 Media thickness

menu”

Refer to sheet 5 04b

Added “5.1.1.1.10 UserCopy

menu”

Refer to sheet 6 04b

Added "5.1.6.2 Page Gap menu". Refer to sheet 6 04b

Added "5.1.17.2 Print Stop menu". Refer to sheet 7 04b

Added "5.1.17.3 Near End menu". Refer to sheet 7 04b

Modified the description of “5.1.25

Header Dump menu”

Refer to sheet 8 04c

Added "5.1.26 Start Feed menu". Refer to sheet 9 04b

Added "5.1.27 Heater Control

menu".

Refer to sheet 9 04b

Added "5.1.28 Alert Buzzer menu". Refer to sheet 10 04c

Chapter

Revised the description of "6.3

Disposal of waste fluids".

Refer to sheet 11 04a

Chapter

Modified the diagram in

“9 Setup menu diagram”

Refer to sheet 12-15 04c

VJ-1324 OPERATION MANUAL ERRATA

ERRATA VJ-1324 OPERATION MANUAL

June 2018

VJ1324E-A-04c 2 MUTOH INDUSTRIES LTD.

3.6 Adjust Print

See the following changes.

・ The function to enter the media thickness is added.

Select “ **>2: Adjust Print>” and press the [>] key. “Thickness 170µm” will be displayed.

Press the [+] or [-] key to enter the media thickness from 80μm to 2800μm and then press the [Enter]

key. For the following procedure, see the operation manual.

・ Confirmation pattern and Adjustment pattern are changed.

When the line is aligned, the bold line on its left side does not have a white vertical line.

・ In the “Custom Rough pattern”, A-F patterns can be adjusted individually.

Press the [Enter] in “Adj.Print2: Custom” and select from “Adj.3: RoughPatternA” to “Adj.8:

RoughPatternF”.

Select “Adj.2: Rough ptn. ALL” to print all patterns.

・ The print information will be printed on the right side of the pattern.

Example of Standard adjustment pattern

ERRATA VJ-1324 OPERATION MANUAL

June 2018

VJ1324E-A-04c 3 MUTOH INDUSTRIES LTD.

Example of Custom adjustment pattern

4.2.6 Media feed compensation

* Revised the step 7 and 8

7. Performs Micro Adjustment Print.

a) Display the Dist.Adj menu on Operation panel in the same way as in Step 1.

b) Press the [+] key or [–] key on Operation panel to select "PF4: Micro Print".

c) Press the [Enter] key on Operation panel.

・ "Warming up Skip ->E" is displayed on Operation panel.

・ While "Warming Up" is displayed, do not touch Platen and Media guide. They become very hot and you

could burn yourself.

・ You can start printing during warming up.

Operation manual “4.4.7 Starting printing during warming up”

・ "Printing" is displayed on Operation panel.

(The printer starts printing after warming up is complete.)

・ Starts micro adjustment printing.

・ In the pattern, look for a place that has least white lines or overlapping in images.The number printed

below the adequate pattern is the micro change value.

ERRATA VJ-1324 OPERATION MANUAL

June 2018

VJ1324E-A-04c 4 MUTOH INDUSTRIES LTD.

・ After the micro adjustment printing is completed, “Micro Change: 0.00%” is displayed on Operation panel.

8. Sets up Micro Adjustment Change.

a) Press the [+] key or [–] key and enter the micro adjustment value according to the printing result in Step 7.

b) Press the [Enter] key on Operation panel.

・ The micro adjustment value is saved. (The saved micro change value will be always shifted to the base

value for the pattern printing.)

・ “PF4: Micro Print” is displayed on Operation panel.

・ The adjustment of media feed compensation value is complete.

ERRATA VJ-1324 OPERATION MANUAL

June 2018

VJ1324E-A-04c 5 MUTOH INDUSTRIES LTD.

5.1.1.1 User Type menu

The following menu is added to the list after “Vacuum Fan”.

Setup item Setting Description

Type 1 - Type 30 Media Thickness Set the media thickness that you use.

[Enter] key: shifts to the sub menu.

UserCopy Copies the setting values of the user type currently

selected to a different user type collectively.

[Enter] key: shifts to the sub menu.

5.1.1.1.9 Media thickness menu

Set the media thickness that you use.

Once the media thickness is entered, print quality is automatically adjusted.

Setup item Setting Description

Media Thickness 80µm to <170µm> to

2800µm

Enter the thickness of the media you are using in

increments of 10µm.

- [Enter] key: saves the setting and shifts to the previous

menu.

[Cancel] key: cancels the setting and shifts to the

previous menu.

5.1.1.1 User Type menu

This menu is to automatically adjust print quality to a certain extent. If you want to improve print

quality, manually adjust it. 3.6 Adjust Print

There is no problem even if you adjust print quality without setting the media thickness.

ERRATA VJ-1324 OPERATION MANUAL

June 2018

VJ1324E-A-04c 6 MUTOH INDUSTRIES LTD.

5.1.1.1.10 UserCopy menu

Copies the setting values of the user type currently selected to a different user type collectively. The following

setting values are copied.

・ Print mode

・ Effect

・ Adjustment value for the adjustment print

・ Feed compensation (initial adjustment printing length, initial adjustment value, micro adjustment value)

・ Pre-heater/Platen/Dryer

・ Vacuum Fan

・ Media Thickness

Setup item Setting Description

UserCopy <1> - 15, ALL

When user type is set to 1:

<2> to 15, ALL

・The setting values of the current user type are copied to the

selected user type.

・When you have selected ALL, the setting values of the current

user type are copied to the all other user types.

- ・[Enter] key: saves the setting and shifts to the previous menu.

・[Cancel] key: cancels the setting and shifts to the previous menu.

5.1.1.1 User Type advanced setup menu

5.1.6.2 Page Gap menu

When "Output Mode" is set to "Take up", the menu is shifted to "Page Gap".

In the Page Gap menu, you can change the margin setting between images.

Setup Item Setting Description

Page Gap <Normal> The margin setting between images is same as the

previous specification.

Narrow The margin setting between images is smaller than

Normal.

・[Enter] key: saves the setting and shifts to the next

menu.

Operation Manual “5.4.6.1 Ink Dry Time menu”

・[Cancel] key: cancels the setting and shifts to the

previous menu.

Operation Manual “5.1.6 Output Mode menu”

ERRATA VJ-1324 OPERATION MANUAL

June 2018

VJ1324E-A-04c 7 MUTOH INDUSTRIES LTD.

5.1.17.2 Print Stop menu

You can set whether or not to display “Roll Remain Error” and pause printing when the length of the roll media that

is counted inside the printer becomes 0.

Normally you can set this as “Off” as the rear sensor detects when the roll paper is finished.

If you are using the roll media that does not come off the paper core easily when it is finished, printing may not be paused

when the roll media is finished, if the print pause menu is set to “Off”. If this happens, set this to “On”.

When “Roll Remain Error” or “Roll Near End” has occurred while the Print Pause menu is set to “On”, if you lower the media

set lever after replacing to the new roll media, the Roll Media Length Setting menu is displayed. Enter the length of the roll

media you have set.

Setup Item Setting Description

Print Stop <Off> The roll media remaining count is not used to judge for pausing

printing. Printing pauses when the rear sensor responds.

[Enter] key: saves the setting and shifts to the sub menu.

Operation Manual “5.1.17 Roll Length menu”

On Even when the rear sensor does not respond, printing pauses when

the roll media remaining count becomes 0.

[Enter] key: saves the setting and shifts to the sub menu.

Operation Manual “5.1.17.3 Near End menu”

- ・[Cancel] key: cancels the setting and shifts to the previous menu.

Operation Manual “5.1.17 Roll Length menu”

5.1.17.3 Near End Menu

You can display “Roll Near End: *m” (* is replaced with a number between 1 and 10) before the length of the

roll media that is counted inside the printer becomes 0.

Setup Item Setting Description

Near end <Off> “Near end” is not displayed.

Remain: 10 m to 1 m “Near end” is displayed when the remaining count for the roll media

becomes the length you selected.

- ・[Enter] key: saves the setting and shifts to the previous menu.

Operation Manual “5.1.17 Roll Length menu”

・[Cancel] key: cancels the setting and shifts to the previous menu.

Operation Manual “5.1.17.2 Print Stop menu”

ERRATA VJ-1324 OPERATION MANUAL

June 2018

VJ1324E-A-04c 8 MUTOH INDUSTRIES LTD.

5.1.25 Header Dump menu

This function is to specify whether to print the following information (dump data) of print data.

・ Data Header

・ Number of Dot in Data (Printed only when the header dump setting is "On".)

・ Printer Serial Number

・ Firmware Version

・ Data size

・ Data receiving time

・ The dump data will be used as a reference material to receive technical supports.

・ When a print is executed in connection with computer, the setting of RIP software will be

printed in the "Data Header".

Setup Item Set Value Description

Header Dump <Off> ・ Only a print data will be printed.

・ Damp data will not be printed.

On After printing of print data, the dump data will be printed.

Dump ・ Only a dump data will be printed, but the "Number of Dot in

Data" will not be printed.

・ Print data will not be printed.

Print Prints the last header dump.

If no history is available, “No Print Data” will appear on the operation

panel.

— ・ [Enter] key: saves the setting and shifts to the next menu.

・ [Cancel] Key: Save the set value, and return to the previous

menu.

Operation manual “5.1 Setup menu”

ERRATA VJ-1324 OPERATION MANUAL

June 2018

VJ1324E-A-04c 9 MUTOH INDUSTRIES LTD.

5.1.26 Start Feed Menu

When Start Feed is set, before printing, the printer rewinds or feeds the media the amount specified by the set

value.

Setup Item Setting Description

Start Feed -10mm to <0mm> to 500mm Sets the amount to rewind or feed the media before

printing starts.

・Value over 0: Feeds the media (with a wider margin

before printing starts).

・Value equal to 0: Neither rewinds nor feeds the media.

・Value below 0: Rewinds the media.

- ・[Enter] key: saves the setting and shifts to the previous

menu.

・[Cancel] key: cancels the setting and shifts to the

previous menu.

Operation manual “5.1 Setup menu”

With take-up system: if you want to set “Start Feed” to below 0, set “Page Gap” to “Narrow”.

If not, the Start Feed setting is not reflected properly.

“5.1.6.2 Page Gap menu”

5.1.27 Heater Control Menu

Paper cocklings may occur during printing when heated. This can be minimized by selecting an appropriate setting

as follows.

Setup Item Setting Description

Heater Ctrl <Normal> Default setting.

Select Normal if paper cocklings do not occur.

Fixer Select Fixer to reduce waiting times before printing and

paper cocklings.

Dryer Select Dryer to keep the drying performance after

printing when using a Heavy-Duty Take-up Unit and

minimize paper cocklings.

- ・[Enter] key: saves the setting and shifts to the previous

menu.

・[Cancel] key: cancels the setting and shifts to the

previous menu.

Operation manual “5.1 Setup menu”

ERRATA VJ-1324 OPERATION MANUAL

June 2018

VJ1324E-A-04c 10 MUTOH INDUSTRIES LTD.

5.1.28 Alert Buzzer Menu

Selects how to turn off the printer beep sound when an error occurs.

For unattended printing, you can select Off setting to avoid continuous buzzer beep.

Setup Item Setting Description

Alert Buzzer <On> Press any key on Operation panel to turn off beep

sound.

This is initially setting.

Off After several beeps, the printer automatically turns off

beep sound.

- ・[Enter] key: saves the setting and shifts to the previous

menu.

・[Cancel] key: cancels the setting and shifts to the

previous menu.

Operation manual “5.1 Setup menu”

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere MUTOH Drucker Handbücher

MUTOH

MUTOH Osprey 75 Bedienungsanleitung

MUTOH

MUTOH Valuevet VJ-628X Bedienungsanleitung

MUTOH

MUTOH Spitfire 100 Extreme Bedienungsanleitung

MUTOH

MUTOH Falcon II Outdoor Bedienungsanleitung

MUTOH

MUTOH PJ-1614NXE Bedienungsanleitung

MUTOH

MUTOH ROCKHOPPER 62 inch Bedienungsanleitung

MUTOH

MUTOH RJ-900C series Bedienungsanleitung

MUTOH

MUTOH XpertJet XPJ-1641SR Installationsanleitung

MUTOH

MUTOH Rockhopper 38 Bedienungsanleitung

MUTOH

MUTOH Toucan Hybrid PJ-162-FE Bedienungsanleitung

MUTOH

MUTOH Rockhopper II Series Bedienungsanleitung

MUTOH

MUTOH ValueJet VJ-1604 Bedienungsanleitung

MUTOH

MUTOH VJ-426UF Bedienungsanleitung

MUTOH

MUTOH Rockhopper 38 Bedienungsanleitung

MUTOH

MUTOH Falcon RJ-4100 Bedienungsanleitung

MUTOH

MUTOH DT-Series Bedienungsanleitung

MUTOH

MUTOH VJ-2638X Bedienungsanleitung

MUTOH

MUTOH DrafStation RJ-901X Bedienungsanleitung

MUTOH

MUTOH Spitfire 65/90 Extreme Bedienungsanleitung

MUTOH

MUTOH ValueJet VJ-1624 Bedienungsanleitung

MUTOH

MUTOH Rockhopper 3 Extreme Bedienungsanleitung

MUTOH

MUTOH Rockhopper II Series Bedienungsanleitung

MUTOH

MUTOH VJ-628 ValueJet Bedienungsanleitung

MUTOH

MUTOH VJ-1626UH Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Lexmark

Lexmark 1400 Series Handbuch

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Epson

Epson ET-7750 Betriebsanleitung

Canon

Canon CLBR 460ps Bedienungsanleitung

Eltron

Eltron P210 Guide Bedienungsanleitung

Ricoh

Ricoh MD-P1 Bedienungsanleitung

Epson

Epson SC-F7100 series Bedienungsanleitung

Epson

Epson Stylus C40UX Bedienungsanleitung

Canon

Canon imagePASS-A2 Bedienungsanleitung

Canon

Canon S820D Bedienungsanleitung