MUTOH XPJ-461UF Bedienungsanleitung

Daily Maintenance Sheet for XPJ-461UF

Daily maintenance

g h

jkl

CS3014-00 -1-

Preparation:

Wear the polyethylene gloves (white) over the

plastic gloves (pink).

Wear personal protective equipment such as

goggles, protective mask or clothing.

Important!

Before performing maintenance, make sure to read

“How to handle UV inkjet printer / its supplies”

(supplied with the printer).

Skin or eye contact with UV curable ink may cause skin

inammation or allergic reaction.

When using this product, wear personal protective

equipment (supplied gloves or solventresistant gloves,

goggles or protective eyewear, protective mask,

CAUTION

Tap on the front panel.

Use to choose “Menu 5: Sleep Mode”.

Tap .

When [Sleep Mode1 Start] appears, tap .

When [Sleep Mode Start Enter] appears, tap .

When [Daily Maintenance Start Enter] appears, tap .

When [Unload Media then Tap Enter] appears, remove the media and the jig on the table,

and then tap .

When [Daily Maintenance End Enter] appears, you can start the maintenance with

following steps.

Make sure to complete this maintenance within 5 minutes while the printer is in Daily maintenance state.

The content of this documents are based on the specication of the rmware Ver.1.00 or later.

When to maintain:

After operation (Be sure to perform the following maintenance)

When the media strikes the print head

Required Items:

(a) Polyethylene gloves (Supplied accessories or

Commercial item)

(b) Rubber gloves (Supplied accessories or

Commercial item)

(d) Paper towel (Supplied accessories)

or Polyester knit wiper (Optional accessories)

(e) Dropper (Supplied accessories)

(f) Dedicated maintenance cleaner (Optional

accessories)

(g) Plastic cup (Supplied accessories)

(h) Cleaning stick (Supplied accessories or Optional

accessories)

(i) Tray (Supplied accessories)

(j) Scraper (Supplied accessories)

(k) Protective mask (Commercial item)

(l) Protective clothing (Commercial item)

Use a paper towel supplied with the printer or optional

Polyester knit wiper. DO NOT use a tissue.

Lints or akes on tissue may cause damage to the print head.

DO NOT use non-dedicated maintenance cleaner.

Do not place any object inside the printer.

After printing, the UV-LED lamp may get hot.

Leave it for 30 minutes to cool down and

DO NOT rub into the nozzle surface. It can cause damage to the print head.

If the entire nozzle surface has been moistened,you can stop it.

-2-CS3014-00

Important!

During cleaning, please note the followings:

• Always follow this steps to perform daily maintenance.

When moistening the surface of nozzles, do not use the cleaning stick already used to clean the print head

circumference, cleaning wiper or cap circumference. Doing so may result in damage to the print head.

• Always use a new cleaning stick and dampen it with dedicated maintenance cleaner.

DO NOT use non-dedicated maintenance cleaner. It may cause nozzle clogging.

• Do not touch the tip of a cleaning stick with ngers. If sebum is adhered, it can cause damage to the print head.

• Do not reuse a cleaning stick. Dusts can adhere causing damage to the print head.

2. Moistening the surface of print head nozzles

1. Cleaning of UV Lamp

Look in the stainless tray to check for ink or dust on the UV-LED lamp.

Hold the handle on the front cover to gently

open it.

Use a paper towel to clean dust or ink o the

underside of the UV-LED lamp.

Important!

• Make sure to use the scraper supplied with the printer.

• Do not press the edge of the scraper too hard. This will cause damage to the glass.

• Make sure to put the glass back on the UV-LED lamp after cleaning. Using the printer without the

glass will reduce the intensity of the lamp and will cause damage to the lamp.

Slide up the left side of the exhaust fan cover. The right side screw serves as a fulcrum.

Slide the glass on the bottom of the lamp towards the front to remove it.

Press the scraper on the ink deposits with a slight angle and scrape it o.

Use the paper towel to clean the ink scraped from the glass.

Put the glass back on the lamp.

If the ink cannot be removed completely, remove the emitting window glass from the lamp and

use the supplied scraper to clean it o.

Put a cleaning stick in the plastic cup.

Use the dropper to dampen the swab of

cleaning stick with dedicated maintenance

cleaner. (Amount used: 0.5 ml)

Lightly touch with the cleaning stick to moisten the nozzle surface.

Repeat it a couple of times to moisten the entire nozzle surface.

Look at the bottom side of the carriage.

Using the cleaning stick dampened with the maintenance cleaner, moisten the surface of the

print head nozzles.

3Next clean the print head circumference.

Scraper

5Next moisten the surface of print head nozzles.

-3-CS3014-00

4. Cleaning of cleaning wiper and the circumference of the cap

DO NOT touch the absorber

(the yellow portions in the illustration right)

Use the cleaning stick to clean the left side

surface of the cleaning wiper (a black rubber

part).

Clean the right side surface of the cleaning

wiper.

Use the cleaning stick to remove the ink and

dust on the circumference of the cap.

Hold the position shown on the left and gently

close the cover.

Next finish the daily maintenance.

Cleaning required

1Look at the bottom side of the carriage.

Check if dusts and ink deposit are adhered.

Print head circumference (silver metal part)

Print head guide part (black plastic part)

Use the cleaning stick to remove the ink and dust on the bottom of the carriage.

Print head circumference (silver metal part) Print head guide part (black plastic part)

Next clean the cleaning wiper and the cap circumference.

3. Cleaning of print head circumference

Print head circumference

Print head guide part

Cleaning required

DO NOT touch the surface of a print head (the yellow portions in the illustration below)

If maintenance cleaner is splashed onto the printer,

use a paper towel to wipe it o.

Before proceeding to the next step, if the cleaning stick gets dirty while cleaning, submerge the foam tip

of the stick into the maintenance cleaner in the cup to clean it.

If the dirt does not get o, change the cleaning stick and then proceed to the next step.

-4-CS3014-00

5. Finishing daily maintenance

1Tap on the front panel.

The printer automatically performs the Short

cleaning.

When the Short cleaning is complete, the printer

automatically enters to sleep mode.

Do not reuse a cleaning stick.

Dusts can adhere causing damage to the print head.

Check that the lid of the maintenance cleaner is shut properly and store it.

Used cleaning stick should be put in a plastic bag, etc, and dispose of it in compliance

with local ordinance and instructions of local authorities.

Important!

Dispose of the used cleaning stick.

Use a paper towel to wipe the maintenance cleaner off the dropper.

Dispose of the maintenance cleaner in the plastic cup and dry the cup well using the paper

towel.

Use a paper towel to clean the tray.

Now the daily maintenance is complete.

For purchasing the maintenance items, contact your local Mutoh dealer or

nearest Mutoh sales oce.

Note

VJ-ULVA1-ML500Dedicated Maintenance cleaner

Part NumberName Minimum q’ty per order

PJ-POLYNITWPolyester knit wiper

RH2 Clean stickClean stick

300

100

Make sure that there is enough ink in ink cartridges.

Empty the waste uid tank.

Perform “Daily maintenance (refer to this sheet)”.

To leave the printer in sleep mode for one week or longer, when one week has

passed, perform the following:

Operation manual ”Emptying waste ink tank”

Operation manual ”Checking ink level and replacing ink cartridge”

Check the ink level.

If “Ink Low” is displayed, replace the relevant ink cartridge.

Agitate the ink in the ink cartridge.

Maintenance before leaving printer in sleep mode for a long time

DailyMaintenance

End   ー＞ Enter

Note

Andere Handbücher für XPJ-461UF

Andere MUTOH Drucker Handbücher

MUTOH

MUTOH ValueJet VJ-1638UH Bedienungsanleitung

MUTOH

MUTOH Unwinder Bedienungsanleitung

MUTOH

MUTOH ValueJet VJ-1628X Bedienungsanleitung

MUTOH

MUTOH VJ-1627MH Bedienungsanleitung

MUTOH

MUTOH ValueJet 628 Bedienungsanleitung

MUTOH

MUTOH VJ-2638X Bedienungsanleitung

MUTOH

MUTOH VJ-426UF Bedienungsanleitung

MUTOH

MUTOH Valuevet VJ-628X Bedienungsanleitung

MUTOH

MUTOH DrafStation RJ-901X Bedienungsanleitung

MUTOH

MUTOH VJ-426UF Bedienungsanleitung

MUTOH

MUTOH ValueJet 1604 Bedienungsanleitung

MUTOH

MUTOH ValueJet VJ-1604W Bedienungsanleitung

MUTOH

MUTOH XPJ-661UF Bedienungsanleitung

MUTOH

MUTOH PJ-1614NXE Bedienungsanleitung

MUTOH

MUTOH Viper Extreme Bedienungsanleitung

MUTOH

MUTOH ValueJet VJ-HCIPADPT-UV6 Bedienungsanleitung

MUTOH

MUTOH Rockhopper II Series Bedienungsanleitung

MUTOH

MUTOH Rockhopper 3 Extreme Bedienungsanleitung

MUTOH

MUTOH Rockhopper 38 Bedienungsanleitung

MUTOH

MUTOH Falcon Outdoor 46 Bedienungsanleitung

MUTOH

MUTOH XpertJet XPJ-1641SR Benutzerhandbuch

MUTOH

MUTOH ValueJet VJ-1604 Bedienungsanleitung

MUTOH

MUTOH ValueJet VJ-1204 Betriebsanleitung

MUTOH

MUTOH ValueJet VJ-1204 Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung