Muton ValueJet VJ-1627MH Benutzerhandbuch
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Assembling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Connecting the cables . . . . . . . . . . . . . . . . . . . . . . . . 20
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Test printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Sleep Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Accessing the Manuals . . . . . . . . . . . . . . . . . . . . . . . . 47
Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
• Unauthorized copying or duplication of the whole or part of the contents of this Guide is prohibited.
• Every care has been taken in writing the contents of this Guide, but please contact MUTOH or the dealer you purchased the
product from if you find any unclear, erroneous or otherwise unsatisfactory content in the Guide.
• Please be aware that MUTOH will not be liable in any way for failures or accidents that result from handling or operating the
printer according to any procedures other than those set forth in this Guide.
• Company names and product names that appear in this Guide are registered trademarks of the respective companies.
Unpacking and Initial Setup
Startup Guide
VJ-1627MH
2 Unpacking
1Unpacking
• Four or more people are required to unpack and move this printer.
• Keep this product level when moving it.
Unpacking the printer
[1] Open the packing box and take out each part.
Unpacking
CAUTION
High capacity ink pack adapter
Installation instruction:
Startup Guide (this document)
Printer body
Accessory box
Unpacking 3
[2] Check if the followings are included.
Note
Items marked with an asterisk (*) above are in the accessory box.
Printer: 1
Paper Towel
(Lint-free cloth): 5
*
Cleaning stick: 10
*
Instruction sheet
for dedicated ink:
Japanese / English
*
Software CD: 1
*
Waste fluid tank: 1
*
*
Tray: 1 Waste fluid tank
holder: 1
*
Cleaning wiper: 3
*
*
Dropper (5 ml): 2
Plastic gloves: 100
*
Daily maintenance sheet:
Japanese / English
*
*
Plastic cup (100 ml): 2
Level: 1
*
Flushing box sponge: 10
*
*
Plastic zipper bag: 1 High Capacity
Ink Pack Adapter: 7
Installation Instruction:
Japanese/English (each)
Startup Guide
(this document)
4 Unpacking
Items in the stand box
Check if the followings are included.
Important!
Use the Waste fluid tank holder in the accessory box.
Items in the Media-feed table (optional) box (half side)
Check if the followings are included.
Leg part (Right): 1Leg part (Left): 1
Hexagon socket
head cap screw: 8
Connector bar: 1
Hexagonal wrench: 1 Butterfly screw: 8
Waste fluid tank holder
fixing screw: 4
Waste fluid tank
holder: 1
Base part: 2
Frame: 1
Installation plate
(Right): 1
Hexagon socket
head cap screw: 8
Leg (Right): 1
Leg (Left): 1 Reinforcement: 1
Hexagonal spanner: 2
Screw: 4
Installation plate
(Left): 1
Stopper: 1
Lug screw: 1
Hexagonal wrench: 1
Unpacking 5
In order to install the product and make the initial settings, you will need the following things in addition to the packaged items.
Things to prepare in order to install and use the printer
Important!
Make sure your computer meets the following requirements.
• OS: Windows 10, Windows 8/8.1, Windows 7
Note
Items marked with an asterisk (*) are accessories or supplies.
Be sure to use a power cable of the specified type.
Using any other power cable could result in electric shock or fire.
Computer: 1 Power cable: 3Ethernet cable: 1 Media: 1
Dedicated maintenance
cleaner (1,000 ml): 1
*
**
500 ml
Ink bag: 7
*
500 ml
Cleaner bag: 7
*
WARNING
6 Unpacking
Install this product in a place that:
•islevel
• has no vibration
• has low humidity and little dust
• has small variation in temperature and humidity
• has no drafts (including those from heating or air conditioning equipment) blowing onto it
• has low levels of electromagnetic radiation and noise
Installation location
Minimum installation space
Ensuring a suitable place for installation
Keep the work area well-ventilated.
The fumes from ink could adversely impact your health.
If you experience headache, fatigue or dizziness, immediately get to fresh air. If nausea persists, seek medical
advice.
4,698 mm
650 mm
width x depth
height
Size of printer body
: 2,698 mm x 818 mm
: 1,302 mm
1,000mm
2,818 mm
1,000 mm
1,000 mm
1,000 mm
Size of
printer body
Rear
Front
CAUTION
Unpacking 7
Install the product in an environment that satisfies the conditions in the table below.
Installation environment conditions
Power supply
specifications
Printer Voltage: AC 100 V to 240 V ±10%
Frequency: 50/60 Hz ±1 Hz
Capacity: No less than 3 A
Heater ×2 Voltage: AC 100 V to 120 V ±10% / AC 200 V to 240 V ±10%
Frequency: 50/60 Hz ±1 Hz
Capacity
• Heater 1: No less than 10 A (AC 100V to 120V)
• Heater 1: No less than 10 A (AC 200V to 240V)
• Heater 2: No less than 10 A (AC 100V to 120V)
• Heater 2: No less than 0 A (AC 200V to 240V)
Environmental
conditions
Operating environment Temperature 20 to 28 °C, Humidity 40 to 60%
No condensation
Recommended Printing
Environment
Temperature 22 to 28 °C, Humidity 40 to 60%
No condensation
Environment for storage • Storage without ink charging: up to 6 months
Temperature -20 to +60 °C, Humidity 20 to 80%
• Storage with ink charging: up to 30 days *1*2
Temperature 5 to 30 °C, Humidity 20 to 80%
*1Perform the Daily Maintenance instructed in the Operation
manual.
*2Always leave the printer in sleep mode and check the
remaining ink level once a week.
Agitate ink in the cartridge once a week as instructed.
8 Assembling
Assembling
Follow the procedure below to assemble the stand.
Assemble the printer
Four or more people are required to assemble this printer.
Procedure for assembling the stand
[1] Assemble the right stand.
[2] Attach the right leg part to the right base part so that four screw holes
in the base part are at the front.
[3] Tighten two hexagon socket head cap screws using a hexagonal wrench (supplied accessory).
[4] Assemble the left stand in the same way as in Step 2, 3.
[5] Fasten the connector bar to the right stand using two hexagon socket
head cap screws.
• Attach the connector bar with the groove facing the rear as shown
left.
Assembling
CAUTION
Leg (right)
Base
Hexagon socket head cap
screws
Screw holes
Front
Screw holes
Front
Leg (left)
Base
Hexagon socket head cap
screws
Stand (right)
Connector bar
Hexagon socket
head cap screws the groove surface
Front
Assembling 9
Follow the procedure below to attach the stand to the printer.
[6] Fasten the connector bar to the left stand in the same way as in Step 5.
[7] Attach the waste fluid tank holder to the right stand using four screws.
[8] Shake the stand to make sure that each part is firmly attached.
Procedure for attaching the stand
[1] Turn the four adjusters as shown below to prevent the stand from
moving.
[2] Insert the two transfer stays into the right and left transfer brackets, lift
the printer with four or more people and place it on the stand.
[3] Remove the two transfer stays and fasten the printer to the stand
using eight butterfly screws.
• 1: Transfer stays
•2:Stand
•3:Butterflyscrews
Stand (left)
Connector bar
Hexagon socket
head cap screws
Front
Stand (right)
Screws
Waste uid tank holder
Stand
Adjusters Adjusters
Stand
Transfer stay Transfer stay Transfer bracket
2
3
3
3
2
3
3
3
1
1
10 Assembling
Follow the procedure below to attach the waste fluid tank.
Procedure for attaching the waste fluid tank
[1] Place the waste fluid tank in the waste fluid tank holder.
[2] Attach the waste fluid tube to the tank.
• Attach the waste fluid tube to the tank.
• Pull out the absorbent material tray.
Important!
Make sure the inner tube is fully inserted into the waste fluid tank.
If not, waste ink may be spilled from the tank.
Insert the waste fluid sensor cable into the connector on the bottom
of the printer.
[3] Confirm that the waste fluid valve is closed.
Waste fluid tank
Waste fluid
tube
Absorbent
material tray
Waste fluid sensor
connector
Waste fluid sensor cable
Waste fluid valve
Inhaltsverzeichnis
Andere Muton Drucker Handbücher
Muton
Muton XPJ-1682WR Bedienungsanleitung
Muton
Muton XPJ-461UF Benutzerhandbuch
Muton
Muton XPJ-1682D Bedienungsanleitung
Muton
Muton VJ-1626UH Bedienungsanleitung
Muton
Muton XPJ-1642WR Benutzerhandbuch
Muton
Muton ValuejetVJ-1604 Bedienungsanleitung
Muton
Muton VJ-1608 Hybrid Bedienungsanleitung
Muton
Muton XPJ-1641SR Bedienungsanleitung
Muton
Muton XPJ-1642WR Bedienungsanleitung
