Muton XPJ-461UF Benutzerhandbuch
Site Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Leveling Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Printer Initial Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Test printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Installing MUTOH Status Monitor . . . . . . . . . . . . . . 43
Sleep Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Viewing Operation Manual . . . . . . . . . . . . . . . . . . . . 46
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
• Unauthorized copying or duplication of the whole or part of the contents of this Guide is prohibited.
• Every care has been taken in writing the contents of this Guide, but please contact MUTOH or the dealer you purchased the
product from if you find any unclear, erroneous or otherwise unsatisfactory content in the Guide.
• Please be aware that MUTOH will not be liable in any way for failures or accidents that result from handling or operating the
printer according to any procedures other than those set forth in this Guide.
• Company names and product names that appear in this Guide are registered trademarks of the respective companies.
Unpacking and Initial Setup
Startup Guide
XPJ-461UF
2 Site Preparation
1 Site Preparation
Choose the location which satisfies the requirements below.
• The table must be level.
• Avoid vibration from the neighboring devices.
• Low humidity and free from dust.
• Less chance of temperature and humidity changes.
• Avoid direct sunlight.
•Avoidwater.
• Avoid direct air onto the printer.
• Low levels of electromagnetic waves.
The following space is required for installation.
Installation Location Requirements
Minimum Space Requirements
Note
The above minimum installation space does not include working space. Use this information when you want to install this printer as close
to the wall as possible.
Make sure to secure sufficient working space to safely use the printer.
Important!
When placing the printer on the work table, the right side of the printer should not be more than 300 mm away from the right-
hand edge of the work table. If it has more space, the drain tube may not reach to the container when emptying the waste ink tank.
Site Preparation
1,388 mm
1,872 mm
450 mm
150 mm
50 mm
450 mm Width × Depth
Height
Printer Size
: 1,188 mm × 972 mm
: 597 mm
Front
Rear
Width × Depth
Load capacity
: 850 mm × 900 mm minimum
: 110kg minimum
Recommended Work Table Size
Site Preparation 3
The installation site must meet the power specification and environmental requirements below.
•Printer:
Input voltage: AC 100V to 240V±10%
Input frequency: 50 / 60Hz ±1Hz
Input load current: 4 A (AC 100V - 120V), 2 A (AC 200V - 240V)
• Operating condition:
Temperature: 20°C to 32°C
Humidity: 40% to 60%, non condensing
• Printing Condition:
Temperature: 22°C to 30°C
Humidity: 40% to 60%, non condensing
• Change rate
Temperature: No more than 2 °C per 1 hour
Humidity: No more than 5% per 1 hour
• Printer Storage Condition:
Without ink filled: Up to 6 months (Temperature: -20°C to 60°C, Humidity: 20% to 80%, non condensing)
With ink filled: Up to 30 days*1*2 (Temperature: 5°C to 30°C, Humidity: 20% to 80%, non condensing)
*1Follow the procedure "Daily Maintenance" in the operation manual to perform daily maintenance.
*2Always leave the printer in sleep mode and check the remaining ink level once a week.
Agitate ink in the cartridge once a week as instructed.
• Choose the work table and floor that can safely support the weight of this product.
The total weight of printer is 95 kg.
If the work table and floor do not have sufficient load capacity, it can lead to injury from a fall.
• Keep the work area well ventilated while operating.
Ink odor may cause health problem such as headache, dizziness, or dull. If you experience these symptoms,
stop printer operation and move to fresh air. Seek medical attention if vomit persists.
• Install the product away from the direct sunlight.
Exposure to direct sunlight may cause premature ink curing leading to damage to the product.
• The equipment is not suitable for use in locations where children are likely to be present.
Power Specification
Environmental Requirements
CAUTION
4 Site Preparation
• Ink Storage Condition:
Black / Cyan / Magenta / Yellow / White / Varnish (220 ml each)
- UH21 ink:
Temperature: -10°C to 50°C (The storage period between 40 ℃and 50 ℃should be up to one month)
Humidity: 5% to 85%, non condensing
- US11 ink:
Temperature: 5°C to 35°C
Humidity: non condensing
Cleaning bag (220 ml)(both UH21 and US11 inks)
Temperature: -10°C to 50°C (The storage period between 40 ℃and 50 ℃should be up to one month)
Humidity: 5% to 85%, non condensing
Unpacking 5
1 Unpacking
Before unpacking, read the instructions below and prepare the necessary items.
• Minimum 4 people are required for unpacking, assembling and installation.
• The items listed below are required for installation and initial setup.
Unpacking Preparation
Use the designated power cord.
Failure to do so may result in electric shock or fire.
Important!
Your computer must meet the following minimum requirements:
• OS: Windows 10 (32bit/64bit), Windows 8/8.1 (32bit/64bit), Windows 7 (32bit/64bit)
• CPU: Intel (R) Core (TM) i5 / i7
• Memory: 8GB minimum
• Network: 100BASE-TX Ethernet port and 100BASE-TX Ethernet cable (Category 5 or later)
Note
Items marked with an asterisk (*) above are accessories or supplies.
Unpacking
Computer: 1 Power cord: 1
*
Ethernet cable: 1 Phillips-head
screwdriver: 1
□Media: 1 □Dedicated maintenance
cleaner (500 ml): 1
*
□Cleaning cartridge: 6
*
□Ink cartridge: 6
*
□Low tack tape: 1 □Paper/ Cloth*
*Paper/Cloth:
Itisusedtocovertheworktableor
floorwhenemptyingthewasteink
tank.Pleaseprepareonethatyoucan
discard.
WARNING
6 Unpacking
Unpack the product.
Unpacking the printer
• Minimum four people are required for unpacking and moving this product.
• When taking out the product from the packing box, remove the plastic sheet wrapped around the
product, then take out the product. This will prevent slip and damage to the product.
• Keep the product level while moving it.
[1] Open the packing box and take out the items listed below.
When lifting this product, always grab the handles under the printer.
Holding rear side or sides of the printer or front panel can result in damage to the printer.
CAUTION
Printer body
Accessory box
CAUTION
Unpacking 7
[2] Check if the followings are included.
Note
Items marked with an asterisk (*) above are in the accessory box.
□Waste ink tank
holder: 1
*
□Waste ink tank
cover: 1
*
□Screw M3×6: 13
*
□Waste ink tank: 1
*
□Cleaning stick: 50
**
□Tray: 1
*
□Dropper (5 ml): 2
*
□Plastic cup (100 ml): 1
□Polyethylene gloves: 100
*
□Rubber gloves: 100
*
□Protective goggles: 1
**
□Scraper : 2
□Level: 1
**
□Double open end
spanner: 1 □Hexagon wrench: 1
**
□Cleaning wiper: 3
□Notification sheet:
Japanese / English
*
□Paper Towel
(Lint-free cloth): 5
*
□Daily maintenance sheet:
Japanese / English
*
□Notes for printing
on object:
Japanese / English
*
□Media height guide : 1
□Instruction sheet
for dedicated ink:
Japanese / English
*
□Printer: 1 □Software CD: 1
*
□Startup Guide:
Japanese / English
(this document)
*
□Draintubevalveclamp : 1
**
□Table : 1 □Screwssecuringthetable : 2
8 Unpacking
Installing 9
2 Installing
Follow the steps below to install the printer.
Moving to the installation site
• Minimum four people are required for unpacking and moving this product.
• When taking out the product from the packing box, remove the plastic sheet wrapped around the
product, then take out the product. This will prevent slip and damage to the product.
• Keep the product level while moving it.
[1] Use the grab handles under the printer and lift the printer onto the installation location. A minimum of four people are
required for the installation.
[2] Remove the packing tapes from the covers on the printer.
[3] Hold the handle on the front cover to gently open it.
[4] Remove the packing materials shown on the left.
• Remove the packing material from the UV-LED lamp.
• Remove the packing material from the carriage.
Installing
CAUTION
10 Installing
[5] Remove the screw, and remove the head fixing plate.
• Slide the head fixing plate leftward to take it out.
Important!
Do not scratch any of the components around the UV-LED lamp with the
fixing plate. This could affect print quality.
[6] Remove the protective material under the FFC cable
[7] Use the hexagon wrench to remove eight screws, then remove two
table fixing plates.
[8] Hold the position shown on the left and gently close the cover.
Hold the handle of the front cover and gently open or close the cover.
If excessive force is applied to the cover, it will shorten its life or will damage the printer.
Important!
Keep the UV-LED lamp fixing plate, head fixing plate, table fixing plates and screws for next use.
× 1
× 8
CAUTION
Inhaltsverzeichnis
Andere Muton Drucker Handbücher
Muton
Muton XPJ-1682D Bedienungsanleitung
Muton
Muton ValueJet VJ-1627MH Benutzerhandbuch
Muton
Muton XPJ-1642WR Benutzerhandbuch
Muton
Muton ValuejetVJ-1604 Bedienungsanleitung
Muton
Muton VJ-1626UH Bedienungsanleitung
Muton
Muton XPJ-1642WR Bedienungsanleitung
Muton
Muton VJ-1608 Hybrid Bedienungsanleitung
Muton
Muton XPJ-1641SR Bedienungsanleitung
Muton
Muton XPJ-1682WR Bedienungsanleitung
